Designing and evaluating of jig for holding cylindrical parts for mass production for drilling operation

QR Code

Designing and evaluating of jig for holding cylindrical parts for mass production for drilling operation

The project study is about a designing and evaluating of jig for holding cylindrical parts for mass production of drilling operation. Three design were draw and compared in terms of material and also the strength of the jigs to select the best design. This report begin with an introduction of jigs w...

Full description

Bibliographic Details
Main Author:	Fazlina, Mansor
Format:	Undergraduates Project Papers
Language:	English
Published:	2010
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://umpir.ump.edu.my/id/eprint/1399/ http://umpir.ump.edu.my/id/eprint/1399/1/Fazlina_Mansor_%28CD_5018%29.pdf

Similar Items

Design and fabrication of jig for butt welding
by: Mohd Rosyazwan Hanif, Ishak
Published: (2012)

Design and fabrication of MIG welding jigs
by: Wong, Fei Yong
Published: (2011)

Design and fabrication test jig for cervical bone
by: Perabu, Moorty
Published: (2009)

Analytical derivation of the incomplete cylindrical functions: real parts
by: Sulaeman, Erwin
Published: (2011)

Analytical derivation of the incomplete cylindrical functions: imaginary part
by: Sulaeman, Erwin
Published: (2011)

Design and development of drill bit sharpening jig for bench grinder
by: Ali Zulfakar, Khairudin
Published: (2016)

Evaluation of Design Efficiency using Boothroyd Dewhurst Method for PCB Drilling Machine Products
by: Aqmal Idham, Abdul Shukor, et al.
Published: (2018)

Design and development of digital PID controller to control speed of permanent magnet DC motor for pcb drilling operation
by: Muhammad Altaf, A Jalil
Published: (2007)

Study of delayed cracking behaviors of hydrogen-charged SUS304L deep drawn cylindrical cups under elevated blank holding forces / Mohd Shahir Hadzir
by: Mohd Shahir, Hadzir
Published: (2022)

Motor speed controller using fuzzy logic method for PCB drilling operation
by: Khairul Azmil, Adzmi
Published: (2008)

Thermoelastic solutions for flexure of anisotropic cylindrical shells
by: Syed Mohamed Ali, Jaffar
Published: (2014)

Experimental and simulation results of cylindrical shell buckling
by: Shah, Qasim Hussain, et al.
Published: (2011)

Alternate expansion series for the incomplete cylindrical function
by: Sulaeman, Erwin
Published: (2011)

Surgical drill bit design and thermomechanical damage in bone drilling: A review
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2021)

Cylindrical shell buckling under axial compression load
by: Shah, Qasim Hussain, et al.
Published: (2011)

Design and development of noise reduction device for hand drilling machine
by: Wan Hafizee , Wan Zulkiflee
Published: (2012)

Air-Drill With Accelerometer And Microphone For Composite Drilling Application
by: Wei Tong, Koh
Published: (2022)

Experimental setup of empty and water filled cylindrical shell buckling
by: Shah, Qasim Hussain, et al.
Published: (2011)

Experimental results of empty and water filled cylindrical shell buckling
by: Shah, Qasim Hussain, et al.
Published: (2011)

Simulation setup of empty and water filled cylindrical shell buckling
by: Shah, Qasim Hussain, et al.
Published: (2011)

Simulation results of empty and water filled cylindrical shell buckling
by: Shah, Qasim Hussain, et al.
Published: (2011)

A study of tool wear prediction of cylindrical grinding wheel
by: Mohd Nazmi, Mohd Nordin
Published: (2010)

Recognition of Cylindrical and Conical Features Using Edge Boundary Classification
by: Ismail, N., et al.
Published: (2005)

Wear Analysis On Different Customized Twist Drill Bit Designs In Drilling Cfrp Panel
by: Hashimi, Nur Hatin Raihana
Published: (2021)

Effect of drill point angle on surface integrity when drilling titanium alloy
by: Murad, Muhamad Nasir, et al.
Published: (2014)

Investigation of pouring temperature and holding time for semisolid metal feedstock production
by: Nur Azhani, Abdul Razak, et al.
Published: (2017)

Performance evaluation of uncoated and coated carbide tools when drilling titanium alloy
by: Abd. Rahim, Erween
Published: (2005)

Effect Of Twist Drill Geometry And Drilling Parameters On Thrust Force In Single-Shot Drilling Of Stack-Up Material
by: Chim, Yi Shen
Published: (2017)

Design, fabrication, and analysis of a precision drilling jig for waste reduction: a low-cost solution
by: Syed Mustafa Haider,, et al.
Published: (2024)

Simulation results of liquid slosh in a partially filled cylindrical tank
by: Hussain Shah, Qasim, et al.
Published: (2011)

Experimental study of liquid slosh dynamics in a half filled cylindrical tank
by: Hussain Shah, Qasim, et al.
Published: (2011)

Experimental results of liquid slosh in a cylindrical tank with different fill levels
by: Hussain Shah, Qasim, et al.
Published: (2011)

Numerical and experimental results of liquid slosh in a partially filled cylindrical tank
by: Hussain Shah, Qasim, et al.
Published: (2011)

Natural convection in semi-cylindrical cavity with heat flux boundary conditions into the system
by: Mohamed Ishak, Saiddi Ali Firdaus
Published: (2006)

Final Design Improvement Of Replica Trophy From Prototype To Mass Production
by: Tan, Sher Wen
Published: (2022)

Quality And Performance Analysis Of Drill Tools
by: Subramonian, Sivarao
Published: (2005)

Control of automatic drilling machine by PLC
by: Rahman , Md Mozasser, et al.
Published: (2011)

Optimization of drill bit geometries for minimum thermal damage in bone drilling
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2024)

Adsorption Characteristic of a Two Layer Hollow Cylindrical Silica Bed
by: Ismail, Mohd Azmi

Simulation model of 3D liquid slosh in a partially filled cylindrical tank
by: Hussain Shah, Qasim, et al.
Published: (2011)

Cannot write session to /tmp/vufind_sessions/sess_9r7gijljljt7k0ufk104uij28u