Stress analysis of overlapped crankshafts

QR Code

Stress analysis of overlapped crankshafts

The crankshaft is a complex component, and as such, the influence of its geometric parameters on stresses seen under service loads is not well understood. The objectives of this work are to investigate the effects of a wide range of geometric parameters on stresses in overlapped crankshafts, to find...

Full description

Bibliographic Details
Main Author:	Sime, Anthony P.
Format:	Thesis (University of Nottingham only)
Language:	English
Published:	1998
Subjects:	Cranks and crankshafts strains and stresses
Online Access:	https://eprints.nottingham.ac.uk/11566/

Similar Items

A modified oil lubrication system with flow control to reduce crankshaft bearing friction in a litre 4 cylinder diesel engine
by: Shayler, Paul J., et al.
Published: (2016)

Finite element analysis of stresses and creep in turbine casings
by: Parkes, D.A.C.
Published: (1973)

Stress analysis and the interaction between hole and straight crack in plane elasticity.
by: Yaghobifar, Mohammad
Published: (2011)

Direct Strain and Stress Measurement for Prestressed Steel.
by: Isaak, Suhaila
Published: (2000)

Stresses and deformations in flexible layered pavement systems subjected to dynamic loads
by: Brown, S.F.
Published: (1967)

Stress intensity factor for cracks problems in an elastic half plane using singular integral equations
by: Elfakhakhre, Nawara Rajab Fathullah
Published: (2018)

The behaviour of alumina reinforce metal matrix composite with nanosized particle addition / Jamaliah Md Said
by: Md Said, Jamaliah
Published: (2011)

Crushing behavior and failure modes of kenaf fibre-reinforced composite hexagonal tubes
by: Alkbir, Munir Faraj Almabrouk
Published: (2016)

The stress analysis of thin-walled screwed tubular joints
by: Broadbent, T.P.
Published: (1988)

Effect of specimen preparation method on the stress-strain behavior of sand in plane-strain compression tests
by: Wanatowski, Dariusz, et al.
Published: (2008)

Experimental determination of fatigue life for international rubber hardness degree 60 engine mount rubber
by: Hosseini, Maryam
Published: (2010)

The development of model techniques for prediction of creep strains applied to steam turbine casings
by: Bellamy, R.A.
Published: (1973)

Structural behaviour of thin-walled composited-filled beams / Fauzi, M.A. and Ghazali, E.
by: Fauzi, M.A., et al.
Published: (2014)

Job stress among humanitarian aid workers
by: Jachens, Liza.J.
Published: (2018)

Residual stress analysis and finite element modelling of repair-welded titanium sheets
by: Salerno, G., et al.
Published: (2017)

A sensitivity study of parameters affecting residual stress predictions in finite element modelling of the inertia friction welding process
by: Iracheta, Omar, et al.
Published: (2015)

Strains, deformations and buckling in very thin torispherical pressure vessel ends
by: Campbell, T.D.
Published: (1975)

Experimental studies and theoretical models for concrete columns confined with FRP composites: a review
by: Gora, Abdurra'uf Mukhtar, et al.
Published: (2018)

Valuing option on the maximum of two assets using improving modified Gauss-Seidel method
by: Koh, W., et al.
Published: (2014)

Modal analysis for engine crankshaft
by: Mohamad Saufi, Mohamad Zainury
Published: (2008)

Experimental investigation of the time- and rate-dependent behaviour of unsaturated clays
by: Bagheri, Meghdad
Published: (2018)

Finite element investigation of the incremental deformation of components
by: Sahari, Berkawi Bin
Published: (1984)

Modal analysis for small engine crankshaft
by: Santhana Julias, Henry
Published: (2010)

From binder to mixture: experimental programme on permanent deformation behaviour
by: Elnasri, Mahmoud Masoud Hamza
Published: (2015)

Work stress, smoking status and smoking intensity: an observational study of 46 190 employees
by: Kouvonen, Anne, et al.
Published: (2005)

Design and Stress Simulation of Crankshaft for Slider Crank-Drive Stirling Engine
by: Mohd Farid, Zainudin, et al.
Published: (2015)

Surface kinematics in the Alpine–Carpathian–Dinaric and Balkan region inferred from a new multi-network GPS combination solution
by: Caporali, A., et al.
Published: (2009)

Study on niosh model of job stress: Relationship between role demands, management styles, interpersonal relationship and stress at Pos Logistics Berhad / Nur Elia Nasuha Ahmad
by: Abdul Hadi, Nurul Ain Anisha
Published: (2019)

Airway and parenchymal strains during bronchoconstriction in the precision cut lung slice
by: Hiorns, Jonathan E., et al.
Published: (2016)

Work Stress in the Banking Industries of Australia and South Africa: Drivers of Stress and Legislative Responses to the Issue
by: Bunn, Anna, et al.
Published: (2013)

A Case Study of Stress Management Among UiTM Kedah Students / Maizatul Zulaikha Azizan...[et al.]
by: Azizan, Maizatul Zulaikha, et al.
Published: (2010)

Designing the human stress ontology: A formal framework to capture and represent knowledge about human stress
by: Khoozani, Ehsan, et al.
Published: (2010)

Accuracy in mechanistic pavement design consequent upon unbound material testing
by: Gillett, Simon D.
Published: (2002)

Constitutive modelling of polymers at high rates of strain
by: Owen, Grace Marie
Published: (2024)

Methods to detect and reduce driver stress: a review
by: Chung, Wan-Young, et al.
Published: (2019)

Minority stress in people who identify as transgender: testing the minority stress model
by: Stennett, Sabrina
Published: (2016)

Investigation on Modal Transient Response Analysis of Engine Crankshaft Structure
by: M. S. M., Sani, et al.
Published: (2009)

Reliability Analysis and Prediction of Time to Failure Distribution of an Automobile Crankshaft
by: Salvinder Singh, Karam Singh, et al.
Published: (2015)

Busting out stress: a case study of stress management in Citibank Berhad / Nur Amalina Muzaffar
by: Muzaffar, Nur Amalina
Published: (2012)

Estimation of Arabian rigid plate motion and strain rate accumulation within the Arabian plate using GPS measurements
by: Almuslmani, Bandar Saleh
Published: (2010)