Analysis of corner radius in dry micro WEDM

QR Code

Analysis of corner radius in dry micro WEDM

Dry micro WEDM is a machining process where gas is used as the dielectric medium instead of liquid. This process favored for its environmental friendly nature and its ability in machining complex intricate shapes with great precision. Regardless of its high precision, the machining precision of cutt...

Full description

Bibliographic Details
Main Authors:	Chowdhury, Ahmed Ghalib Khan, Ali, Mohammad Yeakub, Banu, Asfana
Format:	Article
Language:	English English
Published:	International Journal of Mechanical Engineering and Robotics Research. 2018
Subjects:	T Technology (General) T175 Industrial research. Research and development TJ Mechanical engineering and machinery TS Manufactures
Online Access:	http://irep.iium.edu.my/66448/ http://irep.iium.edu.my/66448/1/ICMERR2018_MER02_Corner%20Radius.pdf http://irep.iium.edu.my/66448/7/ICMERR%202018%20Acceptance%20Notification-MER02.pdf

Similar Items

Precision control of kerf in metal cutting using dry micro WEDM: issues and challenges
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Influence of energy parameters of micro WEDM on kerf
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Micro electro discharge machining of nonconductive ceramic: the issue of spalling
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

A metrological inspection method using micro-CT for the analysis of drilled holes in CFRP and titanium stacks
by: Kourra, Nadia, et al.
Published: (2017)

Influence of the angle of cut of workpiece on taper and corner roundness during Wire Electrical Discharge Machining (WEDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Influence of Wire Electrical Discharge Machining (WEDM) process parameters on surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Drying kinetics of cocoa beans undergoing vacuum drying
by: Rahman, S M A, et al.
Published: (2012)

Drying of food products under inert atmosphere using heat pump
by: Hawlader, Mohammad Nurul Alam
Published: (2012)

Hardware implementation of ANFIS controller for gas-particle separations in wet scrubber system
by: Banzomo, Bashir Ahmed, et al.
Published: (2014)

Frameworks for a computational Isnad authentication and mechanism development
by: Ibrahim, Nuzulha Khilwani, et al.
Published: (2016)

Isnad Al-hadith computational authentication: An analysis hierarchically
by: Ibrahim, Nuzulha Khilwani, et al.
Published: (2016)

Estimation of surface pressure distribution on a delta wing with curved leading edges in hypersonic/supersonic flow
by: Crasta, Asha, et al.
Published: (2016)

Improved radiation characteristic of balanced antipodal vivaldi antenna in array configuration
by: Shaikh, Faraz Ahmed, et al.
Published: (2018)

Comparative study of conventional and micro WEDM based on machining of meso/micro sized spur gear
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Assessing organizations readiness toward business intelligence systems: a proposed hypothesized model
by: Anjariny, Ahmed H., et al.
Published: (2012)

Desalination with a solar-assisted heat pump, an economic optimization
by: Amin, Zakaria Mohd., et al.
Published: (2013)

Performance of Photovoltaic Systems with Solar Tracking in Singapore
by: Amin, Zakaria Mohd., et al.
Published: (2012)

Study of falling film evaporation process in a vapor compression desalination system
by: Bahar, Rubina, et al.
Published: (2012)

A review on solar assisted heat pump systems in Singapore
by: Amin , Zakaria Mohd., et al.
Published: (2013)

Desalination of seawater using solar, ambient energy and waste heat from air conditioning system
by: Hawlader, Mohammad Nurul Alam, et al.
Published: (2012)

Acceptability of the concept of shariah compliant procurement in the Malaysian construction industry
by: Che Haron, Faris, et al.
Published: (2019)

Design and fabrication of a simple cost effective spin coater for deposition of thin film
by: Ferdaus, Mohammad Meftahul, et al.
Published: (2014)

Development of a electrically inspired low emission microcontroller based hybrid vehicle
by: Ullah, Mohammad Habib, et al.
Published: (2012)

Non-acidic method for isolation of microcrystalline cellulose from oil palm empty fruit bunch fiber
by: Samat, Noorasikin, et al.
Published: (2018)

Design and material analysis of regenerative dispersion Magnetorheological (MR) damper
by: Abdul Aziz, Mohammad, et al.
Published: (2019)

Nonlinear modeling and simulation of waste energy harvesting system for hybrid engine: fuzzy logic approach
by: Rahman, Mohammed Ataur, et al.
Published: (2013)

A biomechanical analysis of lifting technique: a comparative study of back lift and leg lift in the manufacturing industry
by: Hartomo, Hartomo, et al.
Published: (2003)

The study on production performances of part transporter in flexible manufacturing system by using simulation method
by: Iqbal, Mohammad, et al.
Published: (2012)

Tool wear mechanisms during cutting of soda lime glass
by: Konneh, Mohamed, et al.
Published: (2018)

Machinability of soda lime glass in high speed end milling
by: Konneh, Mohamed, et al.
Published: (2017)

Processing and characterization of durian skin fibers composites: Mechanical properties
by: Manshhor, Mohd Romainor, et al.
Published: (2012)

Effect of maleic anhydride (MA) on thermal properties of polylactic acid (PLA) composites reinforced with durian skin fiber (DSF)
by: M.I, Ahmad Fitrie, et al.
Published: (2012)

Impregnation of cinnamon essential oil into plasticised polylactic acid biocomposite film for active food packaging
by: Anuar, Hazleen, et al.
Published: (2017)

Analysis of WEDM process parameters on surface roughness and kerf using Taguchi method
by: Banu, Asfana, et al.
Published: (2017)

Mechanical properties and failure modes of recycled polypropylene/microcrystalline cellulose composites
by: Zulkifli, Nur Izzati, et al.
Published: (2015)

PID tuned artificial immune system hover control for lab-scaled helicopter system
by: Toha, Siti Fauziah, et al.
Published: (2015)

A study of investigate and eliminate the crack-like flaws in bulk metal forming processes
by: Topa, Ameen, et al.
Published: (2015)

The prospects of panel style nano-battery technology for EV/HEV
by: Rahman, Mohammed Ataur, et al.
Published: (2016)

Low-cost microcontact printing for direct enzyme patterning on paper
by: Ahmad, Siti Khadijah, et al.
Published: (2015)

Microwave hybrid heating of materials using susceptors- a brief review
by: Yahaya, B., et al.
Published: (2014)