Investigation of the anti-wear characteristics of palm oil methyl ester using a four-ball tribometer test

QR Code

Investigation of the anti-wear characteristics of palm oil methyl ester using a four-ball tribometer test

The aim of this study was to assess the anti-wear characteristics of palm oil methyl ester (POME) in elastohydrodynamic lubrication of EN31 steel ball bearings. A conventional four-ball wear testing machine with different loads was used at 1500 rev miny1 and a test duration of 1 min at ambient room...

Full description

Bibliographic Details
Main Authors:	Maleque, Md. Abdul, Masjuki, H.H.
Format:	Article
Language:	English
Published:	Elsevier BV 1997
Subjects:	T175 Industrial research. Research and development TN600 Metallurgy
Online Access:	http://irep.iium.edu.my/29638/ http://irep.iium.edu.my/29638/1/P4_1997.pdf

Similar Items

Bio-fuel-contaminated lubricant and hardening effects on the friction and wear of AISI 1045 steel
by: Maleque, Md. Abdul, et al.
Published: (1998)

Synergistic effect on flexural properties of kenaf-glass hybrid composite
by: Afdzaluddin, Atiqah, et al.
Published: (2013)

Wear behavior of aluminium modified cast iron in comparison with conventional gray cast iron
by: Maleque, Md. Abdul, et al.
Published: (2018)

The effect of palm oil diesel fuel contaminated lubricant on sliding wear of cast irons against mild steel
by: Masjuki, H.H., et al.
Published: (1996)

Effect of SiC particle size on hardness and wear behavior of TIG melted hard surface layer AISI Duplex-2205 Steel
by: Paijan, Lailatul Harina, et al.
Published: (2019)

Effect of SiC particle size on hardness and wear behavior of TIG melted hard surface layer AISI Duplex-2205 steel
by: Paijan, Lailatul Harina, et al.
Published: (2020)

Aluminium-copper-SiCp composite materials corrosion in biodiesel
by: Maleque, Md. Abdul
Published: (2012)

Effect of copper on tensile strength improvement of Al-Cu-SiCp new composite
by: Maleque, Md. Abdul, et al.
Published: (2014)

Wear behavior of modified surface layer produced by TIG melting of preplaced Ti powder in nitrogen environment
by: Mridha, Shahjahan, et al.
Published: (2011)

TIG Torch melting as surface engineering technology
by: Azwan, Muhammad, et al.
Published: (2020)

Enhancing tool life of hot isostatically pressed silicon nitride inserts in machining inconel 718 with different susceptors through hybrid microwave post sintering
by: Ariff, Tasnim Firdaus, et al.
Published: (2018)

Physical property of multi walled carbon nanotube reinforced aluminium nano composite
by: Maleque, Md. Abdul
Published: (2013)

The tribological behaviour of Fe-C-Al cast iron – effect of temperature
by: Maleque, Md. Abdul, et al.
Published: (2013)

Modelling aspect of corrosive wear under biodiesel
by: Adebisi, Adetayo A., et al.
Published: (2011)

Evaluation of sustainable micro-alloyed HSLA steel for pipeline application
by: Musa, M. H. A., et al.
Published: (2020)

Effect of ball milling parameters on the synthesization of carbon nanotube aluminium nano composite
by: Abdullah, Umma, et al.
Published: (2013)

Engineered hexagonal boron nitride utilizing environmental friendly co-deposition technique
by: Maleque, Md. Abdul, et al.
Published: (2014)

Characterization of carbon nanotube aluminium nano composite- effect of ball milling time on particle size
by: Abdullah, Umma, et al.
Published: (2013)

Experimental study of flank wear in high speed turning of stainless steel AISI 304
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2013)

Grain refinement in ferritic stainless steel welds: The journey so far
by: Amuda, M.O.H., et al.
Published: (2010)

Effect of energy input on microstructure and hardness of TIG Welded AISI 430-Ferritic stainless steel
by: Amuda, M.O.H., et al.
Published: (2011)

Development of thermoplastic natural rubber (TPNR) as a new binder in metal injection moulding
by: Omar, Mohd Afian, et al.
Published: (2016)

Low temperature fluidized bed nitriding of austenitic stainless steel
by: Haruman, E., et al.
Published: (2006)

Wear surface characteristics study of tribo-materials under palm oil methyl ester added lubricant
by: Maleque, Md. Abdul, et al.
Published: (2002)

Wear, performance and emissions of a two-stroke engine running on palm oil methyl ester blended lubricant
by: Masjuki, H.H., et al.
Published: (1996)

The effect of intercritical heat treatment on the mechanical properties of AISI 3115 steel
by: Maleque, Md. Abdul, et al.
Published: (2004)

Utilization of palm oil biomass for treatment of low grade Malaysian iron ore
by: Hadi Puwanto, purwanto
Published: (2014)

Enhancement magnetic properties of Malaysian iron ore by biomass treatment
by: Purwanto, Hadi
Published: (2014)

The effects of various TPNR binder compositions on feedstock preparation for MIM process
by: Hassan, Norita, et al.
Published: (2015)

Development of carbon-infiltrated bio-char from oil palm empty fruit bunch
by: Rozhan, Alya Naili, et al.
Published: (2015)

Fabrication and compressive properties of low to medium porosity closed-cell porous aluminum using PMMA space holder technique
by: Jamal, Nur Ayuni, et al.
Published: (2016)

Effect of charcoal derived from oil palm empty fruit bunch on the sinter characteristics of low grade iron ore
by: Hadi, Purwanto, et al.
Published: (2018)

Hardness and fracture toughness analysis of ZTA–SWCNT ceramic cutting inserts
by: Hamidon, Nor Ezzati, et al.
Published: (2019)

Analysis on physical and microstructural properties of ZTA-SWNT ceramic cutting tool
by: Abdul Molok, Salma, et al.
Published: (2019)

Utilization of low-grade iron ore in ammonia decomposition
by: Othman, Nur Ezzah Faezah, et al.
Published: (2016)

A novel scheme for weld microstructure control using cryogenic cooling
by: Muhammed Olawale Hakeem, Amuda, et al.
Published: (2011)

Parametric study of carbide precipitation in 16% chromium ferritic stainless steel (FSS) welds
by: Amuda, Muhammed Olawale Hakeem, et al.
Published: (2011)

Biotar ironmaking using wooden biomass and nanoporous iron ore
by: Hata, Yuichi, et al.
Published: (2009)

Phase formation during reduction of iron sand with soda ash flux addition
by: , Pramusanto, et al.
Published: (2011)

Reduction of iron ore/empty fruit bunch char briquette composite
by: Yunus, Nurul Azhani, et al.
Published: (2013)