Nanotechnology education at undergraduate level: Malaysian
scenario

QR Code

Nanotechnology education at undergraduate level: Malaysian scenario

This paper shall firstly presents the nanotechnology research, investment, education, etc. in the developed countries such as North America, European Union, Japan, etc. Then, the present activities and future action plan for Malaysian nanotechnology were compared. This was done as Malaysia is a f...

Full description

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, Ismail, Ahmad Faris
Format:	Proceeding Paper
Language:	English
Published:	2008
Subjects:	T Technology (General) TJ Mechanical engineering and machinery TS Manufactures
Online Access:	http://irep.iium.edu.my/27386/ http://irep.iium.edu.my/27386/1/074_STSS_2008_871-879.pdf

Similar Items

Microengineering education in IIUM: challenges and successes
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Micro Electro Discharge Milling for Microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Focused ion beam micromachining of mems
by: Ali, Mohammad Yeakub
Published: (2008)

Micro-drilling of metallic materials for microsystems technology
by: Ali, Mohammad Yeakub
Published: (2008)

Geometrical integrity of microholes produced by micro-EDM
by: Ali, Mohammad Yeakub
Published: (2008)

Nanopillar Array for Cell Culture Dish
by: Ali, Mohammad Yeakub
Published: (2011)

Micro-manufacturing technology: the huge opportunity of thinking small
by: Ali, Mohammad Yeakub
Published: (2011)

Powder mixed micro electro discharge machining (PMμEDM)
by: Ali, Mohammad Yeakub
Published: (2011)

Noble tool based micromilling for nanometric surface finish
by: Ali, Mohammad Yeakub
Published: (2011)

Application of focused ion beam for machining of nanopillar sheet
by: Ali, Mohammad Yeakub
Published: (2011)

Development of micro end milling process for fabricating MEMS
by: Ali, Mohammad Yeakub
Published: (2009)

Enhancing Soil Health: Nanotechnologies for Effective Remediation and Sustainable Development
by: Kho, Brendan Lik Sen, et al.
Published: (2024)

An analytical approximation technique for the duffing oscillator based on the energy balance method
by: Hosen, Md. Alal, et al.
Published: (2017)

Surface roughness analysis of beryllium-copper alloy in micro end milling
by: Mehfuz, R., et al.
Published: (2007)

Design and fabrication of micro swiss-roll combustor mold by micro EDM milling
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Experimental study of conventional wire electrical discharge machining for microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Fabricating hot embossing micro tool using electrodischarge machining
by: Mohammad, Ammar Sami, et al.
Published: (2006)

Polymeric micro-fluidic channel by hot embossing
by: Mohammad, Amar Sami, et al.
Published: (2006)

Focused ion beam machining of cell culture dish
by: Ali, Mohammad Yeakub
Published: (2008)

Application of silicon carbide in abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2011)

High-order approximate solutions of strongly nonlinear cubic-quintic Duffing oscillator based on the harmonic balance method
by: Chowdhury, Md. Sazzad Hossien, et al.
Published: (2017)

An investigation on morphology of hard-brittle silicon surface by diamond grinding
by: Konneh, Mohamed, et al.
Published: (2006)

Sputtering of paraboloid microstructure using fib
by: Ali, Mohammad Yeakub, et al.
Published: (2006)

Rheological and thermal behaviour of high impact polystyrene nanocomposite
by: Al-Ghamdi, Ahmed S., et al.
Published: (2012)

Effect of Process Parameters on Abrasive Contamination During Water Abrasive Jet Machining of Mild Steel
by: Afifah, Ali, et al.
Published: (2010)

Comparative study of conventional and micro WEDM based on machining of meso/micro sized spur gear
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Investigation of microholes produced by focused ion beam micromachining
by: Mohd Fuad, Nurul Hajar, et al.
Published: (2011)

Fabrication of silicon nanopillar sheet for Cell Culture Dish
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Fabrication of Silicon Nanopillar Sheet for Cell Culture Dish
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Investigation of Microholes Produced by Focused Ion Beam Micromachining
by: Mohd. Fuad, Nurul Hajar, et al.
Published: (2010)

Fabrication of Micropillar Sheet for Cell Culture Dish
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Fabrication of Bio-MEMS Nanostructure by focused ion beam
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Micromilling of tungsten carbide using focused ion beam
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Simulation of micro-injection molding
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Knowledge-based approach for stretch blow molding
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Fabrication of micro cavities by micro electrical discharged machining
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Fabrication of three dimensional micro-components – A review
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Surface roughness of FIB sputtered silicon
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Fabrication of micropillar sheet for cell culture dish
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Mass-replication of micro-components
by: Ali, Mohammad Yeakub, et al.
Published: (2003)