An introduction to electrical discharge machining (EDM)

QR Code

An introduction to electrical discharge machining (EDM)

Abstract. The fundamental features of electrical discharge machining (EDM) were discussed in this chapter. The machining principle and its outcomes were highlighted in this chapter. The input variable of EDM presented here are electrical and non-electrical ones. The output of EDM process are given i...

Full description

Bibliographic Details
Main Authors:	Khan, Ahsan Ali, Mohammed, Baba Ndaliman
Format:	Book Chapter
Language:	English
Published:	International Islamic University Malaysia 2011
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/25557/ http://irep.iium.edu.my/25557/2/Chapter_13.pdf

Similar Items

Surface modification of titanium alloy through electrical discharge machining (EDM)
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Surface Modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy
by: Mohammed , Baba Ndaliman, et al.
Published: (2013)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of electrical discharge machining process parameters on surface micro-hardness of titanium alloy
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Influence of TaC Powder Additive on electrical discharge machining of stainless Steel
by: Mohd Zain, Zakaria, et al.
Published: (2011)

Wear ratio and work surface finish during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Improving micro-hardness of stainless steel through powder-mixed electrical discharge machining
by: Mohd Zain, Zakaria, et al.
Published: (2014)

Improving machining performance using alumina powder-added dielectric during electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Developments in EDM process variables
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface alloying of Ti-6Al-4V using Cu-TaC composite electrode during electrical discharge machining
by: Mohammed Baba, Ndaliman, et al.
Published: (2011)

Development of Powder Metallurgy (PM) compacted Cu-TaC electrodes for EDM
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2011)

Influence of work and tool materials on parameters of electrical discharge machining(EDM)
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Formation of nitrides and carbides on titanium alloy surface through EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2012)

Performance of PM compacted Cu-TaC electrodes during EDM
by: Mohammed, Baba Ndaliman, et al.
Published: (2011)

Role of heat transfer on process characteristics during electrical discharge machining
by: Khan, Ahsan Ali
Published: (2011)

Influence of thermal conductivity cf electrodes on EDM process parameters
by: Khan, Ahsan Ali, et al.
Published: (2012)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd Zain, Zakaria, et al.
Published: (2012)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd. Zain, Zakaria, et al.
Published: (2012)

Influence of electrode profiles on electrical discharge machining of titanium
by: Zain, Zakaria Mohd, et al.
Published: (2011)

Determination of influential factors on EDMed surface properties using Plackett-Burman design
by: Ndaliman, Mohammed Baba, et al.
Published: (2012)

Determination of influential factors on edmed surface properties using plackett-burman design
by: Ndaliman, Mohammed Baba, et al.
Published: (2012)

Effect of electrical parameters on performance of Cu-TiC mixed ceramic compact electrode in EDM process
by: Khan, Ahsan Ali, et al.
Published: (2013)

Investigation of the influence of the properties of the work and tool materials on performance level of Electrical Discharge Machining (EDM) process
by: A.K.M., N. Amin, et al.
Published: (1997)

Analyzing the influence of electrical parameters on EDM process of Ti6Al4V alloy using Adaptive Neuro-fuzzy Inference System (ANFIS)
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2015)

Influence of process parameters on electrical discharge machined job surface integrity
by: Iqbal, A.K.M. Asif, et al.
Published: (2010)

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Mohammed Baba, Ndaliman, et al.
Published: (2013)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Temperature distribution in copper electrode during electrical discharge machining process
by: Abdulkareem, Suleiman, et al.
Published: (2017)

Surface modification by EDM using Co-Cr sintered powder metallurgy electrode
by: Khan, Ahsan Ali, et al.
Published: (2012)

Surface modification by EDM using CO-CR sintered powder metallurgy electrod
by: Khan, Ahsan Ali, et al.
Published: (2012)

Analysis of microlayer defects of a functionally graded titanium alloy by electrical discharge machining
by: Abdulkareem, Sulaiman, et al.
Published: (2018)

Reducing electrode wear ratio using cryogenic cooling during electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2009)

Surface quality produced in EDM with tungsten carbide and copper compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2015)

Modeling of EDM Process parameters for Machining Stainless Steel using Copper Electrodes
by: Khan, Ahsan Ali, et al.
Published: (2008)

The Effect of EDM with external magnetic field on surface roughness of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2013)

Relationship between machining variables and process characteristics during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2011)