Optical tomography: the potential of mass flow rate in rice industry

Optical tomography: the potential of mass flow rate in rice industry

The capability of Optical Tomography (OT) to visualize pipe flow is undeniably beneficial and of utmost importance to solid gas industry. The other striking feature of OT is its ability to measure and analyze real-time mass flow rate (MFR), which enables online monitoring of material weight. This pa...

Full description

Bibliographic Details
Main Authors:	Mohd. Muji, Siti Zarina, Abdul Rahim, Ruzairi, Abdul Shaib, Mohd Fadzli, Mohd Fadzil, Naizatul Shima, Rahiman, Mohd Hafiz Fazalul, Zainal Abidin, Zuhairiah
Format:	Article
Published:	Elsevier 2015
Subjects:	TK7800-8360 Electronics
Online Access:	http://dx.doi.org/10.1016/j.snb.2015.02.078 http://dx.doi.org/10.1016/j.snb.2015.02.078 http://eprints.uthm.edu.my/6856/1/siti_zarina_mohd_muji_U.pdf

Similar Items

Aplikasi 12C menggunakan PIC 18F4520
by: Mohd Muji, Siti Zarina, et al.
Published: (2011)

MIMO antenna performances on microstrip antenna with EBG structure for WLAN applications
by: Othman, NurNasyilla, et al.
Published: (2014)

Design and modeling of linear back projection (LBP) algorithm for field programmable gate array (FPGA)
by: Podari, Norhidayati, et al.
Published: (2014)

Comparison between two different types of microcontroller in developing optical tomography controller unit
by: Abdul Shaib, Mohd Fadzli, et al.
Published: (2013)

Electrical & electronic engineering : theory and application series 2 : embedded system, mechatronic and image processing
by: Mohd. Muji, Siti Zarina, et al.
Published: (2015)

Design, modeling and implementation of antennas using electromagnetic bandgap material and defected ground planes
by: Zainal Abidin, Zuhairiah
Published: (2011)

Application of microwave in wood tomography
by: A. Jalil@Zainuddin, Mohd Hafiz
Published: (2005)

Electrical & electronic engineering: theory and applications
by: Mohd Muji , Siti Zarina, et al.
Published: (2016)

Development of plasmonic sensor for detection of toxic materials
by: Morsin, Marlia, et al.
Published: (2015)

Real-time visualising image of flame by laser based transmission tomography
by: Mohamad, Elmy Johana, et al.
Published: (2006)

Measurement and analysis of water/oil multiphase flow using electrical capacitance tomography sensor
by: Mohamad, E. J., et al.
Published: (2016)

Optical tomography experimental setup: a study on reflection effect
by: Mohd Muji, Siti Zarina, et al.
Published: (2011)

Optical tomography: a new filter technique for post processing image
by: Mohd Muji , Siti Zarina, et al.
Published: (2012)

Four element antenna array working at 2.4/5.2 GHz for wireless USB dongle applications
by: Zainal Abidin, Zuhairiah, et al.
Published: (2012)

Rectangular patch with partial ground wearable antenna for 2.4 GHz applications
by: Wan Marzudi, Wan Noor Najwa, et al.
Published: (2015)

The linearity of optical tomography: sensor model and experimental verification
by: Mohd. Muji , Siti Zarina, et al.
Published: (2011)

Development of one cycle current controller using raspberry pi for 3 phase active power filter for nonlinear load improvement
by: Mohamad Shari, Mohd Hafiz
Published: (2015)

Performance of star patch antenna on a paper substrate material
by: Wan Marzudi, Wan Noor Najwa, et al.
Published: (2015)

3D modelling of electrical capacitance and ultrasonic sensor integration using finite element method
by: Pusppanathan, Jaysuman, et al.
Published: (2015)

The application of wire mesh ground plane in open area test site for radiated emission measurement
by: Wibowo, Ignatius Agung, et al.
Published: (2011)

Influence of Rf power in copper sputtering plasma measured by optical emission spectroscopy
by: Kevin, L., et al.
Published: (2013)

An overview on the measurement uncertainty evaluation of electromagnetic compatibility test
by: Ayob, Mohd Erdi, et al.
Published: (2016)

An overview on the measurement uncertainty evaluation of electromagnetic compatibility test
by: Ayob, Mohd Erdi, et al.
Published: (2016)

An overview on the measurement uncertainty evaluation of electromagnetic compatibility test
by: Ayob, Mohd Erdi, et al.
Published: (2016)

Analysis of crude palm oil composition in a chemical process conveyor using electrical capacitance tomography
by: Mohamad, E. J., et al.
Published: (2016)

Optical tomography: transmitter and receiver circuit preparation
by: Mohd Muji , Siti Zarina, et al.
Published: (2011)

Optical tomography verification for single and mixed modalities
by: Mohd Muji, Siti Zarina, et al.
Published: (2017)

Statistical analysis and filter design for conducted emission noise
by: Zainal, Mohd Shamian
Published: (2003)

GSM-based notification system for electronic pigeon hole
by: Abd Wahab, Mohd Helmy, et al.
Published: (2010)

Multi-channel all-optical regeneration based on time-interleaving and higher-order four-wave mixing in fiber
by: Mohd Shah, Nor Shahida, et al.
Published: (2010)

Development of attendance system using biometric fingerprint identification
by: Katiran, Norshidah, et al.
Published: (2010)

Development of parallel and fan-shaped beam mixed-projection optical tomography
by: Mohd Muji , Siti Zarina, et al.

A study on optical sensors orientation for tomography system development
by: Abdul Shaib, Mohd Fadzli, et al.
Published: (2012)

10GB/S NRZ based on self-phase modulation in all optical 2R regeneration
by: Mat Yaacob, S.N.S., et al.
Published: (2015)

An Optical Tomography System Using a Digital Signal Processor
by: Rahim, Ruzairi Abdul, et al.
Published: (2008)

Mass flow rate in gravity flow rig using optical tomography
by: Mohd Muji, Siti Zarina, et al.
Published: (2015)

Prediction of radiated emissions from high speed PCB traces using travelling wave antenna model
by: Mohd Sayegh, Ahmed, et al.
Published: (2014)

Study on finite element analysis of fine solid lines by flexographic printing in printed antennas for RFID transponder
by: Maksud, M. I., et al.
Published: (2013)

An investigation into printing processes and feasibility study for WID tag antennas
by: Maksud, M. I., et al.
Published: (2013)

A study on printed multiple solid line by combining microcontact and flexographic printing process for microelectronic and biomedical applications
by: Maksud, M. I., et al.
Published: (2013)