PCD inserts in end milling of Aluminum Silicon Carbide (AlSiC)

Metal matrix composites (MMC) falls under the category of potential engineering materials applicable to the automotive and aerospace industries. This is become their excellent properties, such as the capability to resist elevated temperature, improved strength, higher stiffness, low density, impr...

Full description

Bibliographic Details
Main Authors:	M. K. , Nor Khairusshima, Amin, A. K. M. Nurul, Ismail, Ahmad Faris
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/23613/ http://irep.iium.edu.my/23613/ http://irep.iium.edu.my/23613/4/chp34.pdf

id	iium-23613
recordtype	eprints
spelling	iium-236132012-09-14T01:02:36Z http://irep.iium.edu.my/23613/ PCD inserts in end milling of Aluminum Silicon Carbide (AlSiC) M. K. , Nor Khairusshima Amin, A. K. M. Nurul Ismail, Ahmad Faris TJ Mechanical engineering and machinery Metal matrix composites (MMC) falls under the category of potential engineering materials applicable to the automotive and aerospace industries. This is become their excellent properties, such as the capability to resist elevated temperature, improved strength, higher stiffness, low density, improved wears and creep resistance and higher elastic modulus. Among these materials aluminum alloys reinforced with silicon carbide found most attentions [1]. AlSiC is preferred over ceramics materials because of their higher combination of properties such as high strength, ductility and high temperature resistance, compared to ceramics [2]. Li et al [3] found that aluminum alloys reinforced with silicon carbide particles are almost three times more efficient than the un-reinforced aluminum alloys in destroying tungsten projectiles at 1.2 km/sec. AlSiC has been considered for use in automobile brake discs and various components in internal combustion engines. Aluminum silicon carbide (AlSiC) is also being widely used in the electronic packaging industries. Though the properties of this new engineering material are quite attractive, the machinability of AlSiC is very poor. Poor machinability is associated with abrasive wear, which make it a class of difficult-tomachine advanced materials [4]. The hardness in the range the silicon carbide phase is comparable with that of tungsten carbide (WC), and is mainly responsible for the high abrasive wear of the tool. Consequently the cutting edge of the tool which in course due to abrasion wear results in the formation of poor surface finish during turning [5]. IIUM Press 2011 Book Chapter PeerReviewed application/pdf en http://irep.iium.edu.my/23613/4/chp34.pdf M. K. , Nor Khairusshima and Amin, A. K. M. Nurul and Ismail, Ahmad Faris (2011) PCD inserts in end milling of Aluminum Silicon Carbide (AlSiC). In: Advanced Machining Towards Improved Machinability of Difficult-to-Cut Materials. IIUM Press, Kuala Lumpur, Malaysia, pp. 253-257. ISBN 9789674181758 http://rms.research.iium.edu.my/bookstore/default.aspx
repository_type	Digital Repository
institution_category	Local University
institution	International Islamic University Malaysia
building	IIUM Repository
collection	Online Access
language	English
topic	TJ Mechanical engineering and machinery
spellingShingle	TJ Mechanical engineering and machinery M. K. , Nor Khairusshima Amin, A. K. M. Nurul Ismail, Ahmad Faris PCD inserts in end milling of Aluminum Silicon Carbide (AlSiC)
description	Metal matrix composites (MMC) falls under the category of potential engineering materials applicable to the automotive and aerospace industries. This is become their excellent properties, such as the capability to resist elevated temperature, improved strength, higher stiffness, low density, improved wears and creep resistance and higher elastic modulus. Among these materials aluminum alloys reinforced with silicon carbide found most attentions [1]. AlSiC is preferred over ceramics materials because of their higher combination of properties such as high strength, ductility and high temperature resistance, compared to ceramics [2]. Li et al [3] found that aluminum alloys reinforced with silicon carbide particles are almost three times more efficient than the un-reinforced aluminum alloys in destroying tungsten projectiles at 1.2 km/sec. AlSiC has been considered for use in automobile brake discs and various components in internal combustion engines. Aluminum silicon carbide (AlSiC) is also being widely used in the electronic packaging industries. Though the properties of this new engineering material are quite attractive, the machinability of AlSiC is very poor. Poor machinability is associated with abrasive wear, which make it a class of difficult-tomachine advanced materials [4]. The hardness in the range the silicon carbide phase is comparable with that of tungsten carbide (WC), and is mainly responsible for the high abrasive wear of the tool. Consequently the cutting edge of the tool which in course due to abrasion wear results in the formation of poor surface finish during turning [5].
format	Book Chapter
author	M. K. , Nor Khairusshima Amin, A. K. M. Nurul Ismail, Ahmad Faris
author_facet	M. K. , Nor Khairusshima Amin, A. K. M. Nurul Ismail, Ahmad Faris
author_sort	M. K. , Nor Khairusshima
title	PCD inserts in end milling of Aluminum Silicon Carbide (AlSiC)
title_short	PCD inserts in end milling of Aluminum Silicon Carbide (AlSiC)
title_full	PCD inserts in end milling of Aluminum Silicon Carbide (AlSiC)
title_fullStr	PCD inserts in end milling of Aluminum Silicon Carbide (AlSiC)
title_full_unstemmed	PCD inserts in end milling of Aluminum Silicon Carbide (AlSiC)
title_sort	pcd inserts in end milling of aluminum silicon carbide (alsic)
publisher	IIUM Press
publishDate	2011
url	http://irep.iium.edu.my/23613/ http://irep.iium.edu.my/23613/ http://irep.iium.edu.my/23613/4/chp34.pdf
first_indexed	2018-09-07T04:42:22Z
last_indexed	2018-09-07T04:42:22Z
_version_	1610922424823447552

PCD inserts in end milling of Aluminum Silicon Carbide (AlSiC)

Similar Items