Development of automatic magnetic particle system for automotive parts inspection

Development of automatic magnetic particle system for automotive parts inspection

Bibliographic Details
Main Authors:	Hrairi, Meftah, Rizal, Mohd Shah, Echrif, Salah B. M.
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TJ Mechanical engineering and machinery TL1 Motor vehicles
Online Access:	http://irep.iium.edu.my/19669/ http://irep.iium.edu.my/19669/ http://irep.iium.edu.my/19669/1/Chapter_25.pdf

Similar Items

Performance of an automatic magnetic particle inspection of automotive parts
by: Hrairi, Meftah, et al.
Published: (2011)

Enhancing magnetic particle testing of automotive parts
by: Hrairi, Meftah, et al.
Published: (2011)

Development of a system for automatic magnetic particle inspection of automotive components
by: Hrairi, Meftah, et al.
Published: (2009)

Towards automatic testing and defect recognition in magnetic particle inspection
by: Hrairi, Meftah, et al.
Published: (2010)

Ultrasonic techniques for detection of thinning defects in metal plates
by: Hrairi, Meftah, et al.
Published: (2010)

Automotive catalytic converters : current status and some future perspectives
by: Mohiuddin, A. K. M., et al.
Published: (2011)

Mixed-convection heat transfer from simulated air-cooled electronic devices: experimental and numerical study
by: Hrairi, Meftah, et al.
Published: (2010)

Advancing automotive agenda
by: Daing Nasir, Daing Ibrahim
Published: (2013)

ICMER discusses issues in mechanical and automotive engineering
by: UMP, PNC

Comparison between composites reinforced with natural and synthetic fibers : Part I
by: Nimir, Yassin Lutfi Mahmud
Published: (2011)

Comparison between composites reinforced with natural fibres and synthetic fibres Part II
by: Nimir, Yassin Lutfi Mahmud
Published: (2011)

Comparison of various types of powertrain used in automotive vehicles in terms of performance and emission
by: Mohiuddin, A. K. M., et al.
Published: (2011)

Investigation of spark ignition multipoint engine using water addition - Part II: performance and emission
by: Mohiuddin, A. K. M., et al.
Published: (2011)

Production of aluminum-silicon carbide composites using powder metallurgy at sintering temperatures above the aluminum melting point part II
by: Nimir, Yassin Lutfi Mahmud
Published: (2011)

Liquid sloshing
by: Hussain Shah, Qasim, et al.
Published: (2011)

Thermodynamic analysis of combustion of CAMPRO CFE engine – part I: simulation
by: Mohiuddin, A. K. M., et al.
Published: (2011)

Thermodynamic analysis of combustion of CAMPRO CFE engine – part II: combustion analysis
by: Mohiuddin, A. K. M., et al.
Published: (2011)

2nd generation IIUM buggy car – Part I: design
by: Mohiuddin, A. K. M.
Published: (2011)

2nd generation IIUM buggy car – part II: fabrication
by: Mohiuddin, A. K. M.
Published: (2011)

Improvement of greenhouse by reducing gas emissions using replacement policy
by: Al Ali, Yousif, et al.
Published: (2012)

Engine noise: An overview on current research trends
by: Hanouf, Zahir, et al.
Published: (2007)

Sonic Under Expanded Flow Control With Micro Jets
by: Syed, Syed Ashfaq, et al.
Published: (2013)

Reynolds averaged navier stokes (RANS) simulation
by: Hoda, Asif
Published: (2011)

Direct numerical simulation (DNS) and large eddy simulation (LES)
by: Hoda, Asif
Published: (2011)

Numerical simulation of complex turbulent flows
by: Hoda, Asif
Published: (2011)

3-Cylinder gasoline direct injection as opposed to 4-cylinder multi-port fuel injection for lower fuel consumption and NOX emission
by: Mohiuddin, A. K. M., et al.
Published: (2011)

Performance investigation of energy efficient hybrid engine towards green technology
by: Rahman, Mohammed Ataur
Published: (2011)

Film cooling of turbine blades
by: Hoda, Asif
Published: (2011)

A study of an aftermarket voltage stabilizer for its performance and emission on passengers vehicle
by: Mohiuddin, A. K. M., et al.
Published: (2011)

Design and fabrication of the testing model of the vehicle structure test system
by: Abdullah, Kassim Abdulrahman, et al.
Published: (2011)

Buckling and crush analysis of light weight structure
by: Abdullah, Kassim Abdulrahman, et al.
Published: (2011)

Analysis of lightweight structural tubes for crashworthy car body
by: Abdullah, Kassim Abdulrahman, et al.
Published: (2011)

Design and fabrication of the second generation IIUM buggy car
by: Abdullah, Kassim Abdulrahman
Published: (2012)

Effect of cross sectional shape on the energy absorbing characteristics of a tube under quasi-static loading
by: Syed Mohamed Ali, Jaffar, et al.
Published: (2013)

Finite element investigatigation of some aspects affecting the depth and wall thickness of a part formed by single point incremental forming process
by: Hrairi, Meftah, et al.
Published: (2011)

Process simulation and quality evaluation of incremental sheet forming
by: Echrif, Salah B. M., et al.
Published: (2011)

Research and progress in incremental sheet forming processes
by: Echrif, Salah B. M., et al.
Published: (2011)

Surface temperature distribution in a composite brake rotor
by: Adebisi, Adetayo A., et al.
Published: (2011)

Structural analysis of the frontal part of a local car model for crashworthiness
by: Abdullah, Kassim Abdulrahman, et al.
Published: (2013)

Automatic car identification system
by: Khalifa, Othman Omran, et al.
Published: (2012)