Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM

The main aim of this paper is to investigate the properties of TaC-Cu electrodes produced by Powder Metallurgy (PM) method. The design of Experiment (DOE) method was used to plan the investigation. Two different compositions of the powders (Cu-TaC with 30 and 55 % wt TaC) were used. The major pro...

Full description

Bibliographic Details
Main Authors:	Mohammed , Baba Ndaliman, Khan, Ahsan Ali
Format:	Conference or Workshop Item
Language:	English
Published:	IIUM 2011
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/1882/ http://irep.iium.edu.my/1882/ http://irep.iium.edu.my/1882/1/Full_paper.pdf

id	iium-1882
recordtype	eprints
spelling	iium-18822011-10-17T07:43:33Z http://irep.iium.edu.my/1882/ Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM Mohammed , Baba Ndaliman Khan, Ahsan Ali TS200 Metal manufactures. Metalworking The main aim of this paper is to investigate the properties of TaC-Cu electrodes produced by Powder Metallurgy (PM) method. The design of Experiment (DOE) method was used to plan the investigation. Two different compositions of the powders (Cu-TaC with 30 and 55 % wt TaC) were used. The major properties which determine suitability of electrodes for Electro Discharge Machining (EDM) are electrical conductivity,thermal conductivity and to some extent density. These properties were measured for the green compacted electrodes,analyzed and compared with their sintered counterparts. This is the initial stage to determine the suitability or otherwise of the compacted electrodes. The results showed that the compacted electrodes in green form can be suitable for EDM, since the electrical conductivities are very high (94.96 – 189.92�-1m-1). The thermal conductivity is good (29.70 – 33.20W/ m K). The density ranges between 6.13 and 9.80 g/cm3. The sintered electrodes were found to be unsuitable at the specified conditions, because they became non-conductive electrically after sintering. Current efforts are geared towards improving these properties for the sintered ones and also determining their optimum levels. IIUM 2011 Conference or Workshop Item PeerReviewed application/pdf en http://irep.iium.edu.my/1882/1/Full_paper.pdf Mohammed , Baba Ndaliman and Khan, Ahsan Ali (2011) Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM. In: International Conference on Mechanical, Automotive and Aerospace Engineering 2011 ICMAAE '11, 17-19 May 2011, Kuala Lumpur, Malaysia. http://www.iium.edu.my/icmaae/2011/
repository_type	Digital Repository
institution_category	Local University
institution	International Islamic University Malaysia
building	IIUM Repository
collection	Online Access
language	English
topic	TS200 Metal manufactures. Metalworking
spellingShingle	TS200 Metal manufactures. Metalworking Mohammed , Baba Ndaliman Khan, Ahsan Ali Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM
description	The main aim of this paper is to investigate the properties of TaC-Cu electrodes produced by Powder Metallurgy (PM) method. The design of Experiment (DOE) method was used to plan the investigation. Two different compositions of the powders (Cu-TaC with 30 and 55 % wt TaC) were used. The major properties which determine suitability of electrodes for Electro Discharge Machining (EDM) are electrical conductivity,thermal conductivity and to some extent density. These properties were measured for the green compacted electrodes,analyzed and compared with their sintered counterparts. This is the initial stage to determine the suitability or otherwise of the compacted electrodes. The results showed that the compacted electrodes in green form can be suitable for EDM, since the electrical conductivities are very high (94.96 – 189.92�-1m-1). The thermal conductivity is good (29.70 – 33.20W/ m K). The density ranges between 6.13 and 9.80 g/cm3. The sintered electrodes were found to be unsuitable at the specified conditions, because they became non-conductive electrically after sintering. Current efforts are geared towards improving these properties for the sintered ones and also determining their optimum levels.
format	Conference or Workshop Item
author	Mohammed , Baba Ndaliman Khan, Ahsan Ali
author_facet	Mohammed , Baba Ndaliman Khan, Ahsan Ali
author_sort	Mohammed , Baba Ndaliman
title	Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM
title_short	Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM
title_full	Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM
title_fullStr	Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM
title_full_unstemmed	Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM
title_sort	development of powder metallurgy (pm) compacted cu-tac electrode for edm
publisher	IIUM
publishDate	2011
url	http://irep.iium.edu.my/1882/ http://irep.iium.edu.my/1882/ http://irep.iium.edu.my/1882/1/Full_paper.pdf
first_indexed	2018-09-07T02:58:31Z
last_indexed	2018-09-07T02:58:31Z
_version_	1610915891018465280

Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM

Similar Items