Decomposition of Manufacturing Processes: A Review

by N. M. Zuki, N. M.
Published 2012

The development of a hybrid knowledge-based system for designing a low volume automotive manufacturing environment

by N. M. Zuki, N. M.
Published 2012

Development Concept of A Portable Quality-Confirmation Inspection Device for Automotive Body Parts

by Bastian Wibar, Momang, N. M. Zuki, N. M.
Published 2015

Design of CF for Automotive Body Parts Based on Artificial Intelligent

by Bastian Wibar, Momang, N. M. Zuki, N. M.
Published 2014

Production Layout Efficiency Improvement for Armoured Vehicle Assembly Line

by Ahmad Shah Hizam, Md. Yasir, N. M. Zuki, N. M.
Published 2017

Alternative structure of new knowledge-based ergonomics risk assessment system

by Fazilah, Abdul Aziz, Zakri, Ghazalli, N. M. Zuki,, N. M.
Published 2016

Productivity and Efficiency Improvement Using Witness Simulation and Ergonomic Study in Automotive Assembly Line

by Ahmad Shah Hizam, Md. Yasir, N. M. Zuki, N. M.
Published 2017

The study of extended single minute exchange of die (SMED) method in 1200 tonnage tandem press line for operation improvement

by A. Q., Basri, N. M. Zuki, N. M.
Published 2017

Assembly Line Efficiency Improvement by Using WITNESS Simulation Software

by Ahmad Shah Hizam, Md. Yasir, N. M. Zuki, N. M.
Published 2018

Experimental Investigation of Turbulent Heat Transfer by Counter and Co-Swirling Flow in a Flat Tube Fitted with Twin Twisted Tapes

by M. Kh., Abdolbaqi, Azmi, W. H., R., Mamat, N. M. Zuki, N. M., G., Najafi
Published 2016

Development of Turret Punch Cutting Tool Using Reverse Engineering Method

by M. M., Noor, R., Daud, K., Kadirgama, M. R. M., Rejab, N. M. Zuki, N. M.
Published 2008

Development of A High Pressure Compressed Natural Gas Mixer for A 1.5 Litre CNG-Diesel Dual Engine

by M. M., Noor, K., Kadirgama, D., Ramasamy, M. R. M., Rejab, N. M. Zuki, N. M.
Published 2008

Importance of the Pre-Requisite Subject

by K., Kadirgama, M. M., Noor, M. R. M., Rejab, N. M. Zuki, N. M.
Published 2008

Regenerative Chatter in End Milling on Mould Aluminum Alloys

by N. M. Zuki, N. M., M. M., Rahman, M. M., Noor, M., Hafizuddin
Published 2008

Strain Rate Effects of Polymeric Foam Cores Under Compressive Loading

by M. R. M., Rejab, N. M. Zuki, N. M., M. M., Noor
Published 2008

Prediction Of Cutting Force By Numerical Solution And Statistic Method In End-Milling Operation.

by K., Kadirgama, M. M., Noor, N. M. Zuki, N. M., M. R. M., Rejab
Published 2008

Planning and Design of a Knowledge Based System for Green Manufacturing Management

by Mohd Kamal, Mohd Nawawi, N. M. Zuki, N. M., Adam Shariff Adli, Aminuddin
Published 2013

Analytic Network Process Model for Sustainable Lean and Green Manufacturing Performance Indicator

by Adam Shariff Adli, Aminuddin, Mohd Kamal, Mohd Nawawi, N. M. Zuki, N. M.
Published 2014

Improvement of productivity in low volume production industry layout by using witness simulation software

by Jaffrey, V., N. M. Zuki, N. M., A. N. M., Rose
Published 2017

A Study of Postural Loading in Malaysian Mining Industry using Rapid Entire Body Assessment

by M. F. F., Ab Rashid, N. M. Zuki, N. M., A. N., Mohd Rose
Published 2017