Fabrication of micro filter by electro discharge machining

by -, Abdus Sabur, Mohammad , Yeakub Ali
Published 2011

Investigation of corner radius using micro wire electro discharge machine

by Sabur, Abdus, Mohammad , Yeakub Ali
Published 2011

Fe-C-Si ternary composite coating on CP-titanium and its tribological properties

by Md Abdul, Maleque, Saffina, W., Ahmad, A.S, Mohammad Yeakub, Ali
Published 2017

Influence of process parameters on surface integrity during EDM of mild steel

by Khan, Ahsan Ali, Adesta, Erry Yulian Triblas, Mohammad , Yeakub Ali
Published 2010

Effect of process parameters on abrasive contamination during water abrasive jet machining of mild steel

by Mohd Ali, Afifah, Khan, Ahsan Ali, Mohammad , Yeakub Ali
Published 2011

Effect of micro end milling tool diameter on minimum chip thickness

by Mohammad , Yeakub Ali, Mansor, Noor Adila, Mass Duki, Siti Hamizah
Published 2011

Micro wire electrical discharge machining of tungsten carbide: methodology and procedure

by Mohammad , Yeakub Ali, Elabtah , Ahmad Chaaban, Alrefaie, Musab Jamal
Published 2011

Micro wire electrical discharge machining of tungsten carbide: analysis of surface roughness

by Mohammad , Yeakub Ali, Elabtah , Ahmad Chaaban, Alrefaie, Musab Jamal
Published 2011

Micro wire electrical discharge machining of tungsten carbide: analysis of material removal rate

by Mohammad , Yeakub Ali, Elabtah , Ahmad Chaaban, Alrefaie, Musab Jamal
Published 2011

Micro electro discharge machining of micro pillar array: analysis of surface finish

by Mohammad , Yeakub Ali, -, Wan Emira Azaty, -, Nor Suriza
Published 2011

Micro electro discharge machining of micropillar array: analysis of material removal rate

by Mohammad , Yeakub Ali, -, Wan Emira Azaty, -, Nor Suriza
Published 2011

Vibration issue in micro end milling

by Mohammad , Yeakub Ali, -, Muhammad Lutfi, -, Mohamad Ismail Fahmi
Published 2011

Machining of ceramic materials: a review

by Sabur, Abdus, M.A., Maleque, Mohammad , Yeakub Ali
Published 2011

Micro/meso milling of aluminium alloy 1100: analysis and modelling of minimum chip thickness

by Mohammad , Yeakub Ali, Mansor, Noor Adila, Mass Duki, Siti Hamizah
Published 2011

Investigation of chip formation and minimum chip thickness in micro/meso milling: Methodology and design of experiment

by Mohammad , Yeakub Ali, Mass Duki, Siti Hamizah, Mansor, Noor Adila
Published 2011

Investigation of minimum chip thickness in micro end milling of PMMA: process development

by Mohammad , Yeakub Ali, -, Asfana Banu, -, Adibah, -, Nur Atikah
Published 2011

Influence of machining parameters on surface roughness during EDM of mild steel

by Khan, Ahsan Ali, Adesta, Erry Yulian Triblas, Mohammad , Yeakub Ali
Published 2011

Formation of micro-cracks and recast layer during EDM of mild steel using copper electrodes

by Khan, Ahsan Ali, Adesta, Erry Yulian Triblas, Mohammad , Yeakub Ali
Published 2011

Developments in EDM process variables

by Khan, Ahsan Ali, Mohammed, Baba Ndaliman, Mohammad , Yeakub Ali
Published 2011

Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy

by Mohammed , Baba Ndaliman, Khan, Ahsan Ali, Mohammad , Yeakub Ali
Published 2013