Search Results - The Blow Parade~
-
1
Design and development of blow mould using machining optimization parameters
Published 2008“…In this work, the objectives were to find the optimized parameters and find out the most dominant variables (cutting speed, federate, axial depth and radial depth).The optimized value has been used to develop a blow mould. …”
Get full text
Get full text
-
2
Investigation of the effects of machining parameters and air blowing on surface topography in high speed end milling of silicon
Published 2012“…Then, the influence of each machining parameter on surface roughness was investigated. From the analyses it was concluded that all three machining parameters and air blowing had significant influence on the surface topography and integrity of silicon.…”
Get full text
Get full text
-
3
-
4
Development of New Genetic Algorithm Software for Blow Mould Process
Published 2008“…In this work, the objectives were to optimized parameters with newly develop software and compare with statistical software. …”
Get full text
Get full text
-
5
-
6
Digital Image Correlation As Deformation Measurement Tool In Plastic Film Blowing Process_
Published 2021“…The progression in deformation and the structural changes as a function of blow up ratio (BUR) and take up ratio (TUR) were studied. …”
Get full text
Get full text
-
7
Numerical solution of bio-nano-convection transport from a horizontal plate with blowing and multiple slip effects
Published 2019“…Our analysis reveals that a higher blowing parameter enhances micro-organism propulsion, flow velocity and nano-particle concentration, and increases the associated boundary layer thicknesses. …”
Get full text
Get full text
Get full text
-
8
-
9
-
10
Optimization of surface roughness in micro-high speed end milling of soda lime glass using uncoated tungsten carbide tool with compressed air blowing
Published 2014“…Also, in this study, a special air delivery nozzle is used to blow away the resultant chips and keep the machined surface clean. …”
Get full text
Get full text
Get full text
-
11
Numerical investigation of Von Karman swirling bioconvective nanofluid transport from a rotating disk in a porous medium with Stefan blowing and anisotropic slip effects
Published 2021“…It is found that that the effects of suction provide a better enhancement of the heat, mass and microorganisms transfer in comparison to blowing. Moreover, physical quantities decrease with higher slip parameters irrespective of the existence of blowing. …”
Get full text
Get full text
-
12
-
13
-
14
Effects of stefan blowing and slip conditions on unsteady MHD casson nanofluid flow over an unsteady shrinking sheet: Dual solutions
Published 2020“…The numerical results reveal that dual solutions exist in some ranges of different physical parameters such as unsteadiness and suction/injection parameters. …”
Get full text
-
15
Techniques And Parameters Investigations On Crosslinked Rubber Foam Formations.
Published 2005“…Heat Tranfer and Heat and Chill techniques were applied to determine suitable methods for crosslinked rubber foam formation. Various parameters such as expansion temperature and blowing agent concentration were also investigated. …”
Get full text
Get full text
-
16
-
17
Experimental and simulation study on the effect of geometrical and flow parameters for combined-hole film cooling
Published 2016“…As the conclusion, a combination of the different geometrical parameters with various flow parameters produced a pattern of results. …”
Get full text
Get full text
Get full text
Get full text
-
18
Heat transfer enhancement through different heat sink/impinging air jet parameters an experimental approach
Published 2023“…The height of the impinging air jet duct, the mode of air flow on the heat sink, air blowing mode and as well as the suction blow mode "pull" and the air jet duct geometry are three important influence parameters on the phenomenon. …”
Get full text
Get full text
-
19
-
20
Parametric optimizing green sand-casting process parameters using hybrid Taguchi grey relational analyses and principal component analyses
Published 2023“…Moisture content, Permeability, Loss of Ignition, Pouring Time & Pouring Temperature selected as input parameters while types of defects (Shrinkage, Blow holes, Cracks, Porosity) as responses for proposed study. …”
Get full text
Get full text