Hard turning of cold work tool steel using wipper ceramic tool

QR Code

Hard turning of cold work tool steel using wipper ceramic tool

While advanced cutting tools used in hard turning applications come with expensive unit price, coated ceramic offers cheaper alternative especially for mid range of hard turning. Wiper geometry featured in coated ceramic tools enabled an increase in productivity or an improved in surface finish desp...

Full description

Bibliographic Details
Main Authors:	Mohd. Yusof, Noordin, Mohd. Zainal, Affandi, Hendriko, Hendriko, Kurniawan, Denni
Format:	Article
Language:	English
Published:	Faculty of Mechanical Engineering, Universiti Teknologi Malaysia 2008
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://eprints.utm.my/8942/ http://eprints.utm.my/8942/1/NoordinMohdYusof2005_HardTurningOfColdWorkTool.pdf

Similar Items

Hard Turning of Stainless Steel using Wiper Coated Carbide Tool
by: Noordin, M.Y., et al.
Published: (2007)

Feasibility of mild hard turning of stainless steel using coated carbide tool
by: Noordin, M., et al.
Published: (2012)

The Effect of Multiple Pass Cutting on Surface Integrity when Hard Turning of AISI D2 Cold Work Tool Steel
by: Kamely, M. A., et al.
Published: (2007)

Experimental study on hard turning of hardened tool steel with coated carbide cutting tools
by: K. Seveen, K. Muniswaran
Published: (2007)

Performance evaluation of coated carbide and coated cermet tools when turning hardened tool steel
by: Mohd. Yusof, Noordin
Published: (2003)

Tool Life of Coated Carbide Cutting Tool when Turning Hardened Stainless Steel under Minimum Quantity Lubricant Using Castor Oil
by: Elmunafi, M., et al.
Published: (2015)

Performance evaluation of coated ceramic cutting tools with T-land edge preparation when turning hardened tool steel
by: Wan Abdul Rahaman, Wan Emri
Published: (2006)

Machining parameters effect in dry turning of AISI 316L stainless steel using coated carbide tools
by: Nur, R., et al.
Published: (2017)

Dry turning of tempered martensitic stainless tool steel using coated cermet and coated carbide tools.
by: Noordin, M. Y., et al.
Published: (2007)

Performance evaluation of coated carbide cutting tools when turning hardened tool steel
by: Tang, Yu Cai
Published: (2006)

Comparison between nitrogen- oil- mist and air-oil- mist condition when turning of hardened tool stainless steel
by: Handawi, M., et al.
Published: (2014)

Effect of cutting speed and feed in turning hardened stainless steel using coated carbide cutting tool under minimum quantity lubrication using castor oil
by: Elmunafi, M., et al.
Published: (2015)

Application of response surface methodology in describing the performance of coated carbide tools when turning AISI 1045 steel
by: Noordin, Mohd Yusof, et al.
Published: (2004)

Modelling of tool life by response surface methodology in hard milling of AISI D2 tool steel
by: Lajis, M. Amri, et al.
Published: (2011)

Development of tooling cost model in high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Application of response surface methodology in describing the performance of coated carbide tools when turning AISI 1045 steel
by: Noordin, M. Y., et al.
Published: (2004)

Performance studies on cryogenic treated carbide cutting tool for turning of AISI304 steel
by: Patil, Nagraj, et al.
Published: (2018)

Developement of ceramic cutting insert of alumina (Al2O3) and zirconia / zirconium oxide (ZrO2) for turning tool steel
by: Shamsudin, Zuraidy
Published: (2007)

Experimental investigations in high-speed hard turning of AISI 4340 steel using mixed ceramic
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Effect of substrate bias on friction coefficient, adhesion strength and hardness of tin-coated tool steel
by: Hamzah, Esah, et al.
Published: (2006)

Tool wear on parallel turning of carbon steel bar
by: Abdul Wahab, Abdul Aziz
Published: (2012)

Tool life modeling in high speed turning of AISI 4340 hardened steel with mixed ceramic tools by using face central cubic design
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2013)

Optimization of Tool Wear using Coupled RSM-GA Approach in Turning of Stainless Steel AISI 304 with Magnetic Damping of Tool Shank
by: Amin, A. K. M. Nurul, et al.
Published: (2015)

Magnetic damping in turning of stainless steel aisi 304 for the reduction of machining vibration and tool wear
by: Amin, A. K. M. Nurul, et al.
Published: (2015)

Effect of tool length on plain turning performance
by: Ibrahim, Norfaizem
Published: (2010)

The use of TiAIN coated carbide tool when finish machining hardened stainless steel
by: Noordin, M. Y., et al.
Published: (2007)

Development of tool life prediction model of TiAlN coated tools during the high speed hard milling of AISI H13 steel
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Application of response surface methodology in describing the performance of coated carbide tools when turning AISI 1045 steel
by: Nordin, M. Y., et al.
Published: (2004)

Modelling of tool life by response surface methodology in hard milling of Aisi D2 tool steel
by: Lajis, Mohd Amri, et al.
Published: (2007)

Effect of Cutting Parameters on Sustainable Machining Performance of Coated Carbide Tool in Dry Turning Process of Stainless Steel 316
by: Bagaber, Salem Abdullah, et al.
Published: (2017)

Morphological evolution during partial re-melting of AISI D2 cold-work tool steel
by: Mohammed, M.N., et al.
Published: (2014)

In-process detection of chipping in ceramic cutting tools during turning of difficult-to-cut material using vision-based approach
by: Lee, W. K., et al.
Published: (2016)

Effect of Machining Parameters on Tool Wear and Hole Quality of AISI 316L Stainless Steel in Conventional Drilling
by: Sultan, A., et al.
Published: (2015)

Tool life estimation model based on simulated flank wear during high speed hard turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2010)

Experimental Investigation of the Effect of Feed Rate and Negative Tool Rake Angle in High Speed Hard Turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2013)

Effect Of Tool Wear On Turned Surface Using Continous Wavelet Transform
by: Thenesh, Selvam
Published: (2017)

Prediction of surface roughness in hard milling of AISI D2 tool steel
by: Lajis, M. A., et al.
Published: (2007)

An experimental investigation of WC-Co tool life and tool wear in turning of titanium / Shamsiatun Shamsuddin
by: Shamsuddin, Shamsiatun
Published: (2016)

An experimental investigation of uncoated WC-Co tool life and wear in turning of stainless steel / Nur Affatin Zawawi
by: Zawawi, Nur Affatin
Published: (2016)

Power demand calculations in turning of aluminum alloy
by: Nur, R., et al.
Published: (2014)