Numerical investigation of the flow inside primary zone of tubular combustor model

QR Code

Numerical investigation of the flow inside primary zone of tubular combustor model

In this study, a numerical simulation of non-reacting flow inside a gas turbine combustor model was performed. The main target of this investigation is to get physical insight of the main vortex, responsible for the efficient mixing of fuel and air. Such models are necessary for developing and optim...

Full description

Bibliographic Details
Main Authors:	Eldrainy, Yehia A., Mohd. Jaafar, Mohammad Nazri, Mat Lazim, Tholudin
Format:	Article
Language:	English
Published:	Faculty of Mechanical Engineering 2008
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://eprints.utm.my/8737/ http://eprints.utm.my/8737/1/YAEldrainy2008-Numerical_Investigation_Of_The_Flow_Inside.pdf

Similar Items

Prediction of the flow inside a micro gas turbine combustor
by: Eldrainy, Yehia A., et al.
Published: (2008)

Combustion characteristic inside micro channel combustor
by: Mohd Rosdzimin Abdul Rahman,, et al.
Published: (2021)

3-D numerical study of the effect of fin discontinuity on heat transfer augmentation in pipes having internal longitudinal fins for turbulent compressible flow
by: Saqr, Khalid M., et al.
Published: (2008)

Combustion characteristics study of biomass in a fluidized bed combustor
by: Abdullah, Haryati, et al.
Published: (2005)

Continuous flow hydrogenations using novel catalytic static mixers inside a tubular reactor
by: Avril, A., et al.
Published: (2017)

Combustor aerodynamic using radial swirler
by: Mohd Jaafar, Mohammad Nazri, et al.
Published: (2011)

The flow of an inhomogeneous fluid inside a sphere
by: Abenov, M.M., et al.
Published: (2022)

Effect of inlet section on pulse combustor performance
by: Abdul Wahid, Mazlan, et al.
Published: (2008)

Thermal Analysis Of Solid Waste Gasifier-combustor.
by: Idroas, M.Y., et al.
Published: (2004)

Development of high efficiency combustor system for industrial furnace
by: Puteri Norfazreen, Razali
Published: (2012)

Preliminary structural design and analysis of a microturbine combustor
by: Ahmad, Mohd. Fauzy
Published: (2008)

Air Distributor Designs for Fluidized Bed Combustors: A Review
by: Ahmmad Shukrie, Md Yudin, et al.
Published: (2016)

Thermoelectric Power System From A Liquid-Fueled Combustor
by: Razali, Muhammad Safuan
Published: (2018)

Development Of A Meso-Scale Combustor For Liquid Fuel Combustion
by: Hamzah, Muhammad Al Amien
Published: (2018)

Design and fabrication of micro swiss-roll combustor mold by micro EDM milling
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Reduction of NOx emissions from gas turbine combustor with fuel staging
by: Mohammad Nazri Mohd.la'afar,
Published: (2002)

Premixed Flameless Combustion Of Producer Gas In A Cyclone Combustor
by: Chanphavong, Lemthong
Published: (2019)

Computational Fluid Dynamic Simulation (CFD) and Experimental Study on Wing-external Store Aerodynamic Interference of subsonic Fighter Aircraf
by: Mat Lazim, Tholudin, et al.
Published: (2004)

Numerical investigation of flow boiling in double-layer microchannel heat sink
by: Ahmed, Shugata, et al.
Published: (2014)

Experimental research on helicopter tail shake phenomenon
by: Ishak, Iskandar Shah, et al.
Published: (2008)

Wind tunnel tests on a generic eurocopter 350Z helicopter
by: Ishak, Iskandar Shah, et al.
Published: (2008)

Development And Performance Characteristics Of A Swirl Combustor Operating On VCO-Blended Fuels
by: Yusri, Muhammed Aqel
Published: (2018)

Analysis of non-dimensional numbers of fluid flowing inside tubes of flat plate solar collector
by: Farhana, K., et al.
Published: (2021)

Steady State Vortex Structure of Lid Driven Flow Inside Shallow Semi Ellipse Cavity
by: M. S., Idris, et al.
Published: (2012)

Combustion Characteristics Of A Swirl Combustor Operating On Kerosene Vegetable Cooking Oil (Vco) Fuel Blends
by: Sulaiman, Mohammad Shah Affandi
Published: (2019)

Flow pattern analysis for oscillatory flow inside resonator tube for thermoacoustic refrigerator using PIV measurement
by: Siti Norsyahira, Mohd Zahari, et al.
Published: (2022)

Numerical analysis of steel tubular member response to ship bow impacts
by: Travanca, J., et al.
Published: (2014)

Characterization and Development of Fluidizing Velocity Profile of Sand Particles in Fluidized Bed Combustor (FBC)
by: Ahmmad Shukrie, Md Yudin, et al.
Published: (2014)

The modification of the perforated plate in the fluidized-bed combustor to analyze heat convection rate and temperature
by: Erdiwansyah, ., et al.
Published: (2021)

Numerical Investigation of In-Cylinder Flow Characteristics of Hydrogen-Fuelled Internal Combustion Engine
by: Hamada, Khalaf I., et al.
Published: (2016)

Numerical investigation of flow field of a non-circular cylinder
by: Mohd Sajali, Muhammad Fahmi, et al.
Published: (2019)

Numerical analysis of in-cylinder flow
by: Afiq, Hamdan
Published: (2008)

A practical numerical approach for the determination of flow contribution of multi-zones wellbores
by: Tarom, N., et al.
Published: (2017)

Combustion efficiency in a fluidized-bed combustor with a modified perforated plate for air distribution
by: Erdiwansyah, ., et al.
Published: (2021)

The effect of fuel feed rate on temperature profiles of a cascading hearth with secondary swirl combustor
by: Wan Mohamed, Wan Ahmad Najmi, et al.
Published: (2002)

Numerical Investigations on the Port Flow Field of a Two-Stroke Poppet Valve Engine
by: Mohd Razali, Hanipah, et al.
Published: (2016)

Combustion modeling of municipal waste combustor
by: Hussain, Ahmad, et al.
Published: (2005)

EXPERIMENTAL INVESTIGATION OF THERMOACOUSTIC INSTABILITIES FOR A MODEL COMBUSTOR WITH VARYING FUEL COMPONENTS
by: Zhang, Xihong, et al.
Published: (2011)

Filament winding technique, experiment and simulation analysis on tubular structure
by: Ma, Quanjin, et al.
Published: (2018)

Design and finite element analysis of solid expandable tubular
by: Aluyah, Sipi
Published: (2006)