Performance of cs-sleeve under direct tensile load: part 1: failure modes

QR Code

Performance of cs-sleeve under direct tensile load: part 1: failure modes

Tensile resistance of a sleeve connector used to connect between two structural components by confining grouted reinforcement bars relies on the bond interaction among reinforcement bars, sleeve and grout. Slippage of the reinforcement bars is customary cause of damage in end-to-end grout-filled...

Full description

Bibliographic Details
Main Authors:	Ling, Jen Hua, Abd. Rahman, Ahmad Baharuddin, Mirasa, Abdul Karim, Abd. Hamid, Zuhairi
Format:	Article
Language:	English
Published:	Faculty of Civil Engineering, Universiti Teknologi Malaysia 2008
Subjects:	TA Engineering (General). Civil engineering (General)
Online Access:	http://eprints.utm.my/8674/ http://eprints.utm.my/8674/1/AhmadBaharudin2008_PerfomanceofCSSleevePart_I_Failure_Modes.pdf

Similar Items

Performance of cs-sleeve under direct tensile load: part II: structural performance
by: Ling, Jeng Hua, et al.
Published: (2008)

Performance of Grouted Splice Sleeve Connector Under Tensile Load
by: Aizat, Alias, et al.
Published: (2013)

Investigation on the shear joints failure with tensile loading for aluminum pins
by: Mohd Firdaus, Mohd Zaid
Published: (2009)

Performance of grouted sleeve connectors in precast wall under four point load test
by: Siti Norzaliah , Mohd Hakimi
Published: (2014)

Laparoscopic sleeve gastrectomy in heart failure patients with left ventricular assist device
by: Punchai, Suriya, et al.
Published: (2019)

Design and development of rotating-sleeve refrigerant compressor
by: Taib, Mohd. Yusof
Published: (2005)

Design and development of rotating-sleeve refrigerant compressor
by: Musa, Md. Nor
Published: (2002)

Structural Performance of Grouted Sleeve Connectors with and without Transverse Reinforcement for Precast Concrete Structure
by: Aizat, Alias, et al.
Published: (2013)

Investigation of failure modes in unreinforced brick masonry walls subjected to different load combinations
by: Bakhteri, Jahangir, et al.
Published: (2003)

Potential Failure Mode In Pergau Spillway
by: Mohd Zaini, Mohamad Zulhisyam
Published: (2022)

Lamp emission and quartz sleeve modelling in slurry photocatalytic reactors
by: Boyjoo, Y, et al.
Published: (2014)

Reinventing with the 3 Cs
by: Abd Razak, Dzulkifli
Published: (2007)

Sleeve fracture of the patella in a child
by: Ahmad Hata, Rasit
Published: (2004)

Failure assessment : comparison of the failure mode between OPC mic and fiber mix concrete slab
by: Cheng, Kam Hao
Published: (2012)

Pile-Sleeve Strength Modelling in API RP2A WSD, LRFD and ISO 19902
by: Sambu Potty, Narayanan, et al.
Published: (2010)

A perceptual computing-based method to prioritize failure modes in failure mode and effect analysis and its application to edible bird nest farming
by: Kok, Chin Chai, et al.
Published: (2016)

Design And Development Of A Single Vane Rotating Sleeve Rotary Compressor For Refrigeration System
by: Mohd Yusof, Taib
Published: (2010)

Thermal investigation on HSPM with new alloy sleeve
by: Zhang, Xiaochen, et al.
Published: (2017)

Experimental evaluation of new pipe sleeve with weep holes for concrete leakage prevention
by: Wan Nazri, Wan Muhammad Hafizuddin
Published: (2018)

Thermomechanical investigations of PEKK-HAp-CS composites
by: Singh, Rupinder, et al.
Published: (2019)

Enhancing a Fuzzy Failure Mode and Effect Analysis methodology with an Analogical Reasoning Technique
by: Tze, Ling Jee, et al.
Published: (2011)

DIUBER (elastic sleeve pads) / Mohd Izwan Nasir
by: Nasir, Mohd Izwan
Published: (2018)

Modes of failure and microscopic failures of Betong bamboo strips loaded in shear, bending, tension and compression / Shahril Anuar Bahari
by: Bahari, Shahril Anuar
Published: (2005)

Structural Analysis Of Stretchable Electronics Joint Under Tensile And Vibration Loading
by: Mustaffa, Nadirah
Published: (2017)

Experimental investigations on novel double-sleeve tubebolt moment connection to concrete filled tubular column / Mahdi Zeinizadeh Jeddi
by: Mahdi Zeinizadeh, Jeddi
Published: (2017)

The influence of modified vegetable oils on tool failure mode and wear mechanisms when turning AISI 1045
by: Amiril Sahab, Abdul Sani, et al.
Published: (2019)

Adjustments to warfarin dosing after gastric bypass and sleeve gastrectomy
by: Nor Hanipah, Zubaidah, et al.
Published: (2018)

Failure Mode and Effects Analysis of Diesel Engine for Ship Navigation System Improvement
by: Faturachman, Danny, et al.
Published: (2013)

In Vitro Evaluation Of The Ferrule Effect And Post Material On Failure Load And Mode In Endodontically Treated Teeth
by: Abbas, Mahmood Alayham
Published: (2012)

Finite Element Simulation of Aluminium/GFRP Fibre Metal Laminate under Tensile Loading
by: M. N. M., Merzuki, et al.
Published: (2018)

Tensile Strength and Failure Characteristics of Common Roof Truss Joints
by: Abdul Rahman, Mahadzir
Published: (2002)

Evaluation of dominant mode of failure of soil nail system using analytical hierarchy process
by: Harahap, I.S.H., et al.
Published: (2010)

Predictors of weight loss 2 years after laparoscopic sleeve gastrectomy
by: Martin, D., et al.
Published: (2015)

Performance of wall panels with grouted sleeve connector under shear and bending
by: Nur Izni, Mohd Khir
Published: (2014)

A study of optimum coconut shell (CS) ratio in cement sand bricks
by: Noorhaya, Kasa
Published: (2015)

Composite failure mechanism of corrugated hybrid composite subjected to bending loading
by: Aminanda, Yulfian, et al.
Published: (2011)

Constraint Estimation Schemes For Semi-Elliptical Surface Cracks Under Tensile And Bending Loads
by: Latiff, Rizman Hariz Abdul
Published: (2017)

Analysis of the behaviour large headed stud in terms of shear resistance and failure mode using abaqus
by: Teh, Kai Yao
Published: (2016)

An Analytical Interval Fuzzy Inference System for Risk Evaluation and Prioritization in Failure Mode and Effect Analysis
by: Tay, Kai Meng
Published: (2015)

Mesoscale modelling of concrete tensile failure mechanism at high strain rates
by: Zhou, X., et al.
Published: (2008)