Application of response surface methodology in describing the performance of coated carbide tools when turning AISI 1045 steel

QR Code

Application of response surface methodology in describing the performance of coated carbide tools when turning AISI 1045 steel

The performance of a multilayer tungsten carbide tool was described using response surface methodology (RSM) when turning AISI 1045 steel. Cutting tests were performed with constant depth of cut and under dry cutting conditions. The factors investigated were cutting speed, feed and the side cutting...

Full description

Bibliographic Details
Main Authors:	Noordin, M. Y., Venkatesh, V. C., Sharif, S., Elting, S., Abdullah, A.
Format:	Article
Published:	Elsevier B V 2004
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://eprints.utm.my/6521/

Similar Items

Application of response surface methodology in describing the performance of coated carbide tools when turning AISI 1045 steel
by: Noordin, Mohd Yusof, et al.
Published: (2004)

Application of response surface methodology in describing the performance of coated carbide tools when turning AISI 1045 steel
by: Nordin, M. Y., et al.
Published: (2004)

Study on surface integrity of AISI 1045 carbon steel when machined by carbide cutting tool under wet conditions
by: N. Fauzi, Tamin, et al.
Published: (2017)

Performance evaluation of coated carbide and coated cermet tools when turning hardened tool steel
by: Mohd. Yusof, Noordin
Published: (2003)

The influence of modified vegetable oils on tool failure mode and wear mechanisms when turning AISI 1045
by: Amiril Sahab, Abdul Sani, et al.
Published: (2019)

The influence of modified vegetable oils on tool failure mode and wear mechanisms when turning AISI 1045
by: Abdul Sani, Amiril Sahab, et al.
Published: (2019)

Finite element simulation of machining AISI 1045 steel using uncoated carbide tool
by: Mohmd Arifin, Nabila Afif
Published: (2012)

Finite element simulation of machining AISI 1045 steel using uncoated carbide tool
by: Mohmd Arifin, Nabila Afif
Published: (2012)

Dry turning of tempered martensitic stainless tool steel using coated cermet and coated carbide tools.
by: Noordin, M. Y., et al.
Published: (2007)

Performance evaluation of coated carbide cutting tools when turning hardened tool steel
by: Tang, Yu Cai
Published: (2006)

Hard Turning of Stainless Steel using Wiper Coated Carbide Tool
by: Noordin, M.Y., et al.
Published: (2007)

Machining parameters effect in dry turning of AISI 316L stainless steel using coated carbide tools
by: Nur, R., et al.
Published: (2017)

The Effect of Multiple Pass Cutting on Surface Integrity when Hard Turning of AISI D2 Cold Work Tool Steel
by: Kamely, M. A., et al.
Published: (2007)

Performance studies on cryogenic treated carbide cutting tool for turning of AISI304 steel
by: Patil, Nagraj, et al.
Published: (2018)

Feasibility of mild hard turning of stainless steel using coated carbide tool
by: Noordin, M., et al.
Published: (2012)

Tool Life of Coated Carbide Cutting Tool when Turning Hardened Stainless Steel under Minimum Quantity Lubricant Using Castor Oil
by: Elmunafi, M., et al.
Published: (2015)

Experimental study on hard turning of hardened tool steel with coated carbide cutting tools
by: K. Seveen, K. Muniswaran
Published: (2007)

A study on cryogenic supercritical carbon dioxide coolant delivery technique when machining of AISI 1045 steel
by: Abd Rahim, Erween, et al.
Published: (2018)

Effect of vegetable and mineral oil-in-water emulsion cutting fluids in turning AISI 4340 steel with coated carbide tools / Sunday Albert Lawal
by: Sunday, Albert Lawal
Published: (2013)

The use of TiAIN coated carbide tool when finish machining hardened stainless steel
by: Noordin, M. Y., et al.
Published: (2007)

Temperature at the tool-chip interface in cryogenic and dry turning of AISI 4340 using carbide tool
by: A. Raof, Natasha, et al.
Published: (2016)

Chip Formation When Drilling AISI 316L Stainless Steel using Carbide Twist Drill
by: Sultan, A., et al.
Published: (2015)

Machinability aspects in heat assisted machining of hardened steel AISI H13 using coated carbide tool
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Bio-fuel-contaminated lubricant and hardening effects on the friction and wear of AISI 1045 steel
by: Maleque, Md. Abdul, et al.
Published: (1998)

Evaluation of wear mechanisms of coated carbide tools when face milling titanium alloy
by: Jawaid, A., et al.
Published: (2000)

Preheating in end milling of AISI D2 hardened steel with coated carbide inserts
by: Lajis , M.A., et al.
Published: (2010)

Finite element modeling of the effect of tool rake angle on cutting force and tool temperature during high speed machining of AISI 1045 steel
by: Sulaiman, Shamsuddin, et al.
Published: (2014)

Multi-objective optimization in friction drilling of AISI1045 steel using grey relational analysis
by: Abdul Mutalib, Mohd Zurrayen, et al.
Published: (2020)

Performance evaluation of coated ceramic cutting tools with T-land edge preparation when turning hardened tool steel
by: Wan Abdul Rahaman, Wan Emri
Published: (2006)

Wear behavior of PVD and CVD coated carbide tools when face milling Inconel 718
by: Jawaid, A., et al.
Published: (2000)

Progressive Tool Flank Wear And Surface Roughness When Turning AISI 1017 Mild Steel Using Reduced Thickness Inserts In Finishing Cutting Conditions
by: S. A., Che Ghani, et al.
Published: (2017)

Effect of Cutting Parameters on Sustainable Machining Performance of Coated Carbide Tool in Dry Turning Process of Stainless Steel 316
by: Bagaber, Salem Abdullah, et al.
Published: (2017)

Effect of nozzle distance and cutting parameters on MQL machining of AISI 1045
by: Amiril Sahab, Abdul Sani, et al.
Published: (2019)

Performance evaluation of uncoated and coated carbide tools when drilling titanium alloy
by: Abd. Rahim, Erween
Published: (2005)

Performance evaluation of uncoated and coated carbide tools when drilling titanium alloy
by: Abd. Rahim, Erween
Published: (2005)

Optimization of surface roughness and tool wear on AISI 4140 using coated Ni-YSZ for CNC turning process
by: Alias, Mohd, et al.
Published: (2020)

Magnetic damping in turning of stainless steel aisi 304 for the reduction of machining vibration and tool wear
by: Amin, A. K. M. Nurul, et al.
Published: (2015)

Investigation on surface roughness of mild steel using coated carbide cutting tools
by: Mohamad Rais, Ramli
Published: (2009)

Performance of coated- and uncoated-carbide tools when drilling titanium alloy—Ti–6Al4V
by: Sharif, Safian, et al.
Published: (2007)

Modelling of tool life by response surface methodology in hard milling of Aisi D2 tool steel
by: Lajis, Mohd Amri, et al.
Published: (2007)