Particle size and injection temperature effect on the injection molding of SS316l powder

QR Code

Particle size and injection temperature effect on the injection molding of SS316l powder

Particle size and injection temperature influence on the injection of SS316L powder has been investigated. The feedstocks used for the investigation being 64 vol. % and 65 vol. %. Results found that the success of the molding process depends on the feedstock rheological properties. Fine powder parti...

Full description

Bibliographic Details
Main Authors:	Jamaludin, Khairur Rijal, Muhamad, Norhamidi, Ab. Rahman, Mohd Nizam, M. Amin, Sri Yulis, Ismail, Muhammad Hussain, Ibrahim, Murtadhahadi
Format:	Article
Language:	English English
Published:	University Publication Centre, Universiti Teknologi Mara, Malaysia 2008
Subjects:	TS Manufactures TJ Mechanical engineering and machinery
Online Access:	http://eprints.utm.my/5820/ http://eprints.utm.my/5820/1/jurnal_UiTM_eprint_publish.pdf http://eprints.utm.my/5820/2/KhairurRijalJamaludin2005_ParticleSizeAndInjectionTemperature.pdf

Similar Items

Rheological properties of SS316l MIM feedstock prepared with different particle sizes and powder loadings
by: M. Amin, Sri Yulis, et al.
Published: (2009)

Particle size and injection temperature effect on the injection molding of SS316L powder / Khairur Rijal Jamaludin … [et al.]
Published: (2008)

An influence of a binder system to the rheological behavior of the SS16l metal injection molding (MIM) feedstock
by: Jamaludin, Khairur Rijal, et al.
Published: (2009)

Optimization of injection molding and solvent debinding parameters of stainless steel powder (SS316L) based feedstock for metal injection molding
by: Muhammad Ilman Hakimi Chua,, et al.
Published: (2013)

Rheological behavior of SS316l gas atomized powder in bimodal particle size distribution in a composite binder system
by: Jamaludin, Khairur Rijal, et al.
Published: (2008)

Rheological Investigation Of Stainless Steel Powder In Bimodal Particle Size Distribution
by: Jamaludin, Khairur Rijal, et al.
Published: (2006)

Debinding process of co-powder injection molded (2C-PIM) SS17-4PH and SS316L
by: Najlaa Nazihah Mas’ood,, et al.
Published: (2020)

Optimizing the injection parameter of water atomised SS316L powder with design of experiment method for best sintered density
by: Jamaludin, Khairur Rijal, et al.
Published: (2009)

Characterization of the feedstock properties of metal injection-molded WC-Co with palm stearin binder system
by: Sri Yulis M. Amin,, et al.
Published: (2014)

Injection molding parameter optimization using the Taguchi method for highest green strength for bimodal powder mixture with SS316L in PEG and PMMA
by: Jamaludina, K. R., et al.
Published: (2008)

Rheological characterization of water atomised stainless steel powder for micro metal injection molding
by: Ibrahim, Mohd. Halim Irwan, et al.
Published: (2009)

Rheological investigation of water atomized metal injection molding (MIM) feedstock for processibility prediction
by: Jamaludin, Khairur Rijal, et al.
Published: (2010)

Analisis taburan saiz partikel serbuk SS316L bagi kegunaan proses penyuntikan acuan logam
by: Jamaludin, Khairur Rijal, et al.
Published: (2008)

Flow behaviour to determine the defects of green part in metal injection molding
by: Mohamad Nor, Nor Hafiez, et al.
Published: (2009)

Effects of debinding and sintering atmosphere on properties and corrosion resistance of powder injection molded 316 L - stainless steel
by: Raza, Muhammad Rafi, et al.
Published: (2017)

Injection molding parameter optimization of titanium alloy powder mix with palm stearin and polyethylene for green defects using taguchi method
by: Mohamad Nor, Nor Hafiez, et al.
Published: (2009)

Moldability of nano size zirconia for powder injection molding process by using PEG and PMMA binders
by: Al Basir,, et al.
Published: (2020)

SS 316L/HA composite via powder injection moulding: Mechanical and physical properties
by: Johari, N. A., et al.
Published: (2019)

Injection Molding of Stainless Steel (SUS 316L) Powder Using a Thermoplastic Binder System
by: Ibrahim, Rosdi
Published: (2002)

Characterization of titanium alloy-hydroxyapatite composite through powder injection molding
by: Mohd Ikram Ramli,, et al.
Published: (2020)

Investigations on metal injection molding of 316L SS using Thermoplastic Natural Rubber (TPNR) binder as a new system
by: Hassan, Norita, et al.
Published: (2012)

Optimization processability of ss316l used natural hydroxyapatite from waste tilapia fish bones in metal injection molding
by: Mustafa, Najwa
Published: (2019)

Flowability and moldability of zirconia micro-part via micro-powder injection molding
by: Muhammad Mohamed Amin,, et al.
Published: (2024)

Orthogonal array technique for optimizing the sintering parameter of the metal injection molding (MIM) compact: best flexure strength
by: Jamaludin, Khairur Rijal, et al.
Published: (2009)

Critical powder loading and the rheology of nanosized cemented carbide with titanium carbide as grain growth inhibitor for injection molding
by: Shahbudin, S.N.A., et al.
Published: (2018)

Control of defects in powder injection molded aluminum matrix composites
by: Ahmad, Faiz
Published: (2008)

Evaluation of sintered hydroxyapatite (HA) via powder injection molding
by: Nashrah Hani Jamadon,, et al.
Published: (2020)

Kesan saiz dan bentuk partikel serbuk SS316l terhadap parameter pengacuanan suntikan logam menggunakan rekabentuk eksperimen
by: Jamaludin, Khairur Rijal
Published: (2009)

Feedstock characterisation of titanium alloy mix with palm stearin binder system for metal injection moulding
by: Mohamad Nor, Nor Hafiez, et al.
Published: (2009)

Effects of vanadium carbide on sintered WC-10%Co produced by micro-powder injection molding
by: Wong, Yee Ning, et al.
Published: (2015)

Physical Properties and Microstructure Study of 316L SS Fabricated by Metal Injection Moulding Process
by: Nur Aidah Nabihah, Dandang, et al.
Published: (2017)

Moldability and solvent debinding of hydroxyapatite micro-part processed through micro-powder injection molding
by: Al Basir,, et al.
Published: (2024)

Moldability characteristics of 3 mol% Yttria Stabilized Zirconia feedstock for micro-powder injection molding process
by: Hafizawati Zakaria,, et al.
Published: (2014)

Debinding process of ss316L metal injection moulding under argon atmosphere
by: Jol, P. Jose, et al.
Published: (2020)

Fabrication of microcomponents by injection molding
by: Yuan , S., et al.
Published: (2004)

Simulation of micro-injection molding
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Effect of space holders on fabrication of porous titanium alloy-hydroxyapatite composite through powder injection molding
by: Farrahshaida Mohd Salleh,, et al.
Published: (2017)

A Study on Injection Moulding and Injection Blow Molding Technology
by: Sokkalingam, Rajalingam
Published: (2009)

Characterization of metal injection molding (MIM) feedstock based on water soluble binder system
by: Muhamad Hussain Ismail,, et al.
Published: (2008)

Physical properties of sintered stainless steel 17-4PH micro-part processed by micro-powder injection molding
by: Abu Bakar Sulong,, et al.
Published: (2022)