Adhesion of chip seal using different type of pre- coating material

QR Code

Adhesion of chip seal using different type of pre- coating material

Chip seal is the common surface treatment that is used in Malaysia recently. A chip seal (also called a “seal coat” or “surface dressing”) is essentially a single layer of asphalt binder that is covered by embedded aggregate with its primary purpose being to seal the fine cracks in the underlying pa...

Full description

Bibliographic Details
Main Author:	Samsudin, Marlina
Format:	Thesis
Language:	English
Published:	2012
Subjects:	TA Engineering (General). Civil engineering (General)
Online Access:	http://eprints.utm.my/49/ http://eprints.utm.my/49/1/MarlinaSamsudinMFKA2012.pdf

Similar Items

Skid resistance performance enhancement using different macrotexture parameters in chip seal
by: Then, Kang Jin
Published: (2017)

Investigation on the different types of materials of joining for automotive panel
by: Mohamad Suhaimi, Samsudin
Published: (2007)

Biological Adhesion
by: Brubaker, C. E., et al.
Published: (2016)

Effectiveness of tyre chips as alternative material in vertical gabion wall to mitigate slope failure
by: Amir Zu Shafiq, Ab Hafiz
Published: (2018)

Effectiveness of tyre chips as alternative material in inclined gabion wall to mitigate slope failure
by: Muhamad Wafiy, Idzani
Published: (2018)

Investigation of saw wood chips with different percentages in sand brick ratio 1:3
by: Nur Syamimi, Azli
Published: (2015)

Mechanical Properties Of Concrete With Different Types Of Glass Waste As Cement Replacement Material
by: Bakar, Amir Syazwan Abu
Published: (2022)

On sealing effects and oxygen dependence of non-recoverable intensity drops in short-chain-conjugated polymers
by: White, J
Published: (2002)

Relationship between surface finish and chips
by: Abdul Gani, Haji Abd. Rahman.
Published: (2002)

Effectiveness of tyre chips as alternative material in gabion wall to ensure slope stability
by: Mohammad Amirul Syukri, Md Zin
Published: (2018)

Analysis the effect of different type valve use at different pressure in piping system
by: Muzakkir, Shukri
Published: (2010)

An efficient approach for vision inspection of IC chips
by: Kok Wah, Liew
Published: (2012)

Influence of Al2O3 nanoreinforcement on the adhesion and thermomechanical properties for epoxy adhesive
by: Nur Zalikha, Khalil, et al.
Published: (2019)

The effectiveness of tires chips in gabion wall for slope protection
by: Hafiz Ashrawi, Baharun
Published: (2019)

Adhesion of bacterial on metal surfaces : effect of surface roughness
by: Noratiqah, Chik
Published: (2015)

Alkalinity of cement mortar containing different types of supplementary cementitious materials under accelerated curing conditions / Sumra Yousuf
by: Sumra , Yousuf
Published: (2021)

Changes of surface dressing texture as related to time and chipping size
by: Yaacob, Haryati, et al.
Published: (2008)

The vero cells growth in different type of microcarriers
by: Ahmad Nor, Yusilawati, et al.
Published: (2011)

Organic soil stabilization by different types of admixtures
by: Noor Suraya, Romali.
Published: (2006)

Assessment On The Performance Of Asphalt Mixtures Prepared With Adhesion Promoters
by: Nge, Jia Sheng
Published: (2019)

Chemical pre-treatment on palm oil clinker as partial cement replacement material in mortar
by: Nor Syahirah, Mahmudin
Published: (2019)

Effect of different sodium chloride (NaCl) concentration on corrosion of coated steel
by: Mohd Firdaus, Ibrahim
Published: (2013)

Types of damage in pin-loaded aluminum plate and other material
by: Mohammad Afifi, Mohammad
Published: (2009)

Design and implementation of an intelligent fuzzy VLSI chip for traffic control application
by: Islam, , Shabiu, et al.
Published: (2006)

Adhesive wear and frictional performance of bamboo fibres reinforced epoxy composite
by: Nirmal, Umar, et al.
Published: (2012)

Investigation on the Synthesis and Conductivity Mechanism of Graphene Based Isotropic Conductive Adhesives
by: Ang, Richard Giap Leng
Published: (2016)

Self-Healing Behaviour of Pre-Cracked Pofa-Concretes in Different Curing Conditions
by: Khairul Anuar, Shahid, et al.
Published: (2014)

Investigation on the different types method of joining for automotive panel
by: Mohd Khairi, Ali
Published: (2007)

Seismic behaviour of tunnels with different soil types and depths
by: Ku Sulaiman, Ku Safirah
Published: (2010)

Effect of rake angle and feed rate on tool wear and surface topography for different chip size in machining carbon steels
by: Mohd Fawzi, Zamri, et al.
Published: (2022)

Development and performance of particleboard from various types of organic waste and adhesives : A review
by: Mohd Nazif, Baharuddin, et al.
Published: (2023)

Investigation of minimum chip thickness in micro end milling of PMMA: process development
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Solder Joint Reliability Of Flip Chip BGA Package
by: Lee, Kor Oon
Published: (2004)

Flexural behavior of concrete beams reinforced with different types of fibers
by: Hind, M. Kh., et al.
Published: (2016)

Hydrochloric acid based pre-treatment on paper mill sludge ash as an alternative source material for geopolymer
by: Nabilah, Mamat, et al.
Published: (2018)

Coating material of air sealing in coal mine: Clay composite slurry (CCS)
by: Zhou, F., et al.
Published: (2013)

Treatment Of Palm Oil Mill Effluent Odour Using Biofilter From Compost And Wood Chips Media
by: Nagalinggam, Tanagaraj
Published: (2017)

Analysis of squat shear wall with different dimensions and position of opening under different type of static loads
by: Ang, Yip Hong
Published: (2015)

The application of adhesive bonding for different types of material for car body parts
by: Muhammad Shahir, Nazir
Published: (2013)

Effectiveness Of Activated Carbon From Bamboo Chips For Industrial Wastewater Treatment
by: Muhammad Fathurrahman, Mohammad Shukor
Published: (2022)