Fe evaluation of thermal property of mould wall material for investment casting and the effect of layers on the hardness of the casting product

QR Code

Fe evaluation of thermal property of mould wall material for investment casting and the effect of layers on the hardness of the casting product

This thesis is aimed to investigate and establish a correlation between the mold wall thickness and the mechanical properties of the non-ferrous alloy in investment casting. Mold material of the fine stucco system is investigated. For the investigation proposes, four molds with different thicknesses...

Full description

Bibliographic Details
Main Author:	Phuan, Yoong Jiann
Format:	Monograph
Language:	English
Published:	Universiti Teknologi Malaysia 2004
Subjects:	TJ Mechanical engineering and machinery TS Manufactures
Online Access:	http://eprints.utm.my/2648/ http://eprints.utm.my/2648/1/75063.pdf

Similar Items

Mould design and mechanical analysis of the casted material
by: Mohd Azuan, Abu Shah
Published: (2010)

Investigation on quality of hydroxyapatite adhesion on investment casting mould
by: Lotfabadi, Amir Fereidouni
Published: (2008)

Design and Simulation on Cast metal Matrix Composite by Investment Casting
by: Taufik, Roni Sahroni, et al.
Published: (2011)

Design and Simulation on Investment Casting Mold for Metal Matrix Composite Material
by: Taufik, Roni Sahroni, et al.
Published: (2011)

The effect of stucco system in ceramic shell investment casting
by: Mohamad Badari, Siti Norbahiyah, et al.
Published: (2011)

Effect of casting temperature on dimensional accuracy in gravity casting
by: Mohd Shariman, Razali
Published: (2009)

Collapsibility of PMMA based material in direct investment casting
by: Shukri, Muhammad Shazwan, et al.
Published: (2018)

Mold design & surface analysis of casted material
by: Annafi, Mohd Khobori
Published: (2010)

Defect analysis on investment casting: a case study
by: Sabudin, Sulastri
Published: (2004)

Design and Simulation on Compressor Metal Matrix Composite by Investment Casting
by: Taufik, Roni Sahroni, et al.
Published: (2011)

Wear properties of Fe-C-Al cast iron and conventional cast iron - a comparative study
by: Maleque, Md. Abdul
Published: (2011)

Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
by: Shaha, Sugrib Kumar, et al.
Published: (2011)

A study on mold material and coating effect in sand casting process
by: Muhammad Fakhri, Zainuddin
Published: (2009)

Study on the microstructure and properties of Fe-C-Si and Fe-C-Al Cast irons
by: Shaha, Sugrib Kumar, et al.
Published: (2011)

Design Simulation of Filing Sequence and Solidification Time for Cast Metal Matrix Composite by Low Pressure Die Casting
by: Taufik, Roni Sahroni, et al.
Published: (2011)

Solidification analysis in permanent mould casting of aluminium alloy LM6 reinforced titanium carbide particulates metal matrix composites
by: Fatchurrohman, Nanang, et al.
Published: (2017)

Design and fabrication of drain cover by casting process
by: Muhamad Amin, Ab Rasak
Published: (2012)

Design and fabrication of hole cover by casting process
by: Muhammad Kamili, Zahidi
Published: (2011)

Rheocasting and Thixocasting: Semi-Solid Casting Technologies
by: S.THIRU,, CHITRAMBALAM
Published: (2010)

Effect of heating time on hardness properties of laser clad gray cast iron surface
by: B., Norhafzan, et al.
Published: (2017)

Solidification Analysis of Aluminium 11.8% Silicon Alloy Reinforced With Titanium Carbide Particulates Produced Using Vortex Mixing - Permanent Mould Casting
by: Fatchurrohman, Nanang, et al.
Published: (2016)

Effect of Lead Addition in LM6 Alloy Castings
by: S.THIRU,, CHITRAMBALAM
Published: (2010)

Investigation of brass microstructure and mechanical properties using metal casting
by: Nur Hamizah, Minhat
Published: (2010)

Effect of melting temperature on dimensional accuracy in sand casting product
by: Ahmad Faizal, Mohamad
Published: (2009)

Investigation on structure and properties of brass casting
by: Haque, Md. Mohafizul, et al.
Published: (2008)

Thermal analysis of two and three-gate sand casting mould
by: Lim, Alex Kheng Booi
Published: (2001)

The effects of vortex gate design on mechanical strength of thin section casting of LM 25 (Al---7Si-0.3Mg) aluminum casting alloy
by: Subhi, Zaid Ali
Published: (2012)

Study On Low-Cycle Fatigue Behavior Of Cast Hybrid Metal Matrix Composites
by: Iqbal, AKM Asif, et al.
Published: (2015)

Effect of mold designs on molten metal behaviour in high-pressure die casting
by: Ibrahim, M.D, et al.
Published: (2017)

Experimental Investigation of Thermal Fatigue Die Casting Dies by Using Response Surface Modelling
by: Hassan Abdulrssoul, Abdulhadi, et al.
Published: (2017)

The Effect of Direct Thermal Method, Temperature and Time on Microstructure of a Cast Aluminium Alloy
by: Asnul Hadi, Ahmad, et al.
Published: (2014)

Reinforcement of rice husk in ceramic shell mould system for investment casting process
by: Kamarudin, Noor Hasliza
Published: (2012)

Collapsibility behaviour of ABS P400 and PMMA used as sacrificial pattern in direct investment casting process
by: Shukri, Muhammad Shazwan
Published: (2017)

Investigation on microstructure and morphology of copper alloy castings
by: M., Nasuha, et al.
Published: (2021)

Analysis of various rapid prototyping techniques for investment casting
by: Marwah, Omar Mohd Faizan
Published: (2016)

Design and simulation on cast metal matrix composite by investment casting
by: Sahroni, Taufik Roni, et al.
Published: (2011)

Effect of thickness on the microstructure and morphology of copper alloy castings
by: M., Nasuha, et al.
Published: (2021)

Defect detection in high pressure die casting product using image processing technology
by: Wahab, Md Saidin
Published: (2003)

Study on Stress Evolution in SiC Particles During Crack Propagation in Cast Hybrid Metal Matrix
by: Iqbal, AKM Asif, et al.
Published: (2015)

Kurtosis quantification of different minimal quantity lubrication effects in machining cast iron with coated and uncoated tool
by: N., Jamil, et al.
Published: (2018)