A Plastic Injection Molding Process Characterisation Using Experimental Technique: A Case Study

QR Code

A Plastic Injection Molding Process Characterisation Using Experimental Technique: A Case Study

This Paper Illustrates An Application Of Design Of Experimental (DOE) Approach In An Industrial Setting For Identifying The Critical Factors Affecting A Plastic Injection Molding Process Of A Certain Component For Aircond Assembly. A Critical To Quality (CTQ) Of Interest Is Reducing Process Defects,...

Full description

Bibliographic Details
Main Authors:	Mohamed Yusoff, Shaik Mohamed, Mohd. Rohani, Jafri, Wan Hamid, Wan Harun, Ramly, Edly
Format:	Article
Language:	English
Published:	Penerbit UTM Press 2004
Subjects:	Q Science (General)
Online Access:	http://eprints.utm.my/1913/ http://eprints.utm.my/1913/1/JTDIS41A01.pdf

Similar Items

The mold cost estimation calculator for plastic injection mold manufacturing
by: Kamalrudin, massila, et al.
Published: (2008)

Modeling plastics injection molding operation using simulation
by: Li Mei, Tan
Published: (2014)

Mold design for plastics injection molding process (two colors) and analysis of gates location
by: Ahmad Zulhelmi, Muhamad
Published: (2009)

The influence of injection molding parameter on properties of thermally conductive plastic
by: Azis, N. Hafizah, et al.
Published: (2017)

Experimental and numerical studies on superhigh strengthening sintered low alloy steels fabricated by metal injection molding)
by: Wan Sharuzi, Wan Harun
Published: (2013)

Optimization Of Injection Molding Parameters Fo Production Of Polypropylene Plastic Tray Using Taguchi Method
by: Wan, Kok Seong
Published: (2005)

A Statistical Experimental Study on Shrinkage of Injection-Molded Part
by: Rajalingam, Sokkalingam, et al.
Published: (2012)

Optimization of process parameters of injection moldings for plastic pallets manufacturing industry
by: Vivekanandan, Panneerselvam, et al.
Published: (2019)

Modeling and Optimization of Injection Molding Process Parameters for a Plastic Cell Phone Housing Component
by: Rajalingam, Sokkalingam, et al.
Published: (2013)

A Study on Injection Moulding and Injection Blow Molding Technology
by: Sokkalingam, Rajalingam
Published: (2009)

Fabrication of microcomponents by injection molding
by: Yuan , S., et al.
Published: (2004)

Simulation of micro-injection molding
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Effect of dimensional parameters on warpage of injection-molded plastic part using response surface methodology
by: Mohd Nasri, Md Salim
Published: (2009)

Design of a plastic injection mold (8 cavities) / Muhammad Fadzli Abdul Rahman and Md Zulkhairi Ismail
by: Abdul Rahman, Muhammad Fadzli, et al.
Published: (2001)

Optimization and numerical simulation analysis for molded thin-walled parts fabricated using wood-filled polypropylene composites via plastic injection molding
by: Md Deros, Mohd Azaman, et al.
Published: (2015)

Numerical Simulation And Experimental Investigations On The Effect Of Polypropylene Rheology In The Injection Molding Process
by: Rusdi, Mohd Syakirin
Published: (2014)

Metal injection molding of implant materials
Published: (2014)

Analysis of filling stage for injection molding
by: Muhammad Arshad, Zainol Abidin
Published: (2007)

Lean manufacturing implementation in a plastic molding industry
by: Mohd Yusuff, Rosnah, et al.
Published: (2012)

Investigation and analysis of finding the injection molding gate by using moldflow
by: Muhamad Fridy Nizam, Harun
Published: (2007)

3D printed mold insert infill analysis for injection molding application
by: Nur Syamimi, Mohd Salleh, et al.
Published: (2024)

Mold Filling Simulation For Injection Molding Of Natural Rubber Compound In Glove Fabrication
by: Maturidi, Nurul Ain Abu Mansor
Published: (2017)

Investigation on mechanical properties of ABS using rapid rpototyping technology and injection molding process
by: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Published: (2009)

Optimization parameters to reduce the warpage defect of plastic injection molding process for a thin-shell part using design of experiment
by: Radhwan, H., et al.
Published: (2019)

Multivariate quality control using an integrated artificial neural network scheme: a case study in plastic injection molding industry
by: Mohd Khairy, Afiz Azry
Published: (2013)

Development of inconel 718 parts produced by metal injection molding technique for aerospace application
by: Suleiman @ Ahmad, Muhammad Jabir
Published: (2019)

Optimization of injection molding and solvent debinding parameters of stainless steel powder (SS316L) based feedstock for metal injection molding
by: Muhammad Ilman Hakimi Chua,, et al.
Published: (2013)

Hot embossing and injection molding of three-dimensional microcomponents
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

A new material supply mechanism for plunger type injection molding
by: Mohamad Al Rassid, Mohamad Borhanudin
Published: (2012)

A new material supply mechanism for plunger type injection molding
by: Mohd Syahmi, Mohd Nong
Published: (2013)

A diagnosis framework for selecting operational improvement opportunities for Malaysian industries
by: Ramly, Edly Ferdin
Published: (2019)

Particle size and injection temperature effect on the injection molding of SS316l powder
by: Jamaludin, Khairur Rijal, et al.
Published: (2008)

Experimental investigation on flexure and impact properties of injection molded polypropylene-nylon 6-glass fiber polymer composites
by: Nuruzzaman, D. M., et al.
Published: (2018)

Numerical Simulation of Fibre Orientation in Simple Injection Molding Processes
by: Oumer, A.N., et al.
Published: (2009)

Control of defects in powder injection molded aluminum matrix composites
by: Ahmad, Faiz
Published: (2008)

Evaluation of sintered hydroxyapatite (HA) via powder injection molding
by: Nashrah Hani Jamadon,, et al.
Published: (2020)

Simulation on effect of preform diameter in injection stretch blow molding
by: Tan, Z Q, et al.
Published: (2018)

Thermoplastic natural rubber (TPNR) as a backbone polymer for metal injection molding
by: Norita Hassan,, et al.
Published: (2013)

Flowability and moldability of zirconia micro-part via micro-powder injection molding
by: Muhammad Mohamed Amin,, et al.
Published: (2024)

Orthogonal array technique for optimizing the sintering parameter of the metal injection molding (MIM) compact: best flexure strength
by: Jamaludin, Khairur Rijal, et al.
Published: (2009)