Effect of hydraulic pressure on hardness, density, tool wear and surface roughness in the fabrication of alumina based cutting tool

QR Code

Effect of hydraulic pressure on hardness, density, tool wear and surface roughness in the fabrication of alumina based cutting tool

Cutting tools can be considered major industrial necessities as it applied mostly to machine components. Development of self-fabricated cutting tool can facilitate lower machining cost as long as the cutting tool can perform effectively. This paper presents the effect of hydraulic pressure on...

Full description

Bibliographic Details
Main Authors:	M. M., Faiz, M., Hairizal, A. B., Hadzley, M. F., Naim, T., Norfauzi, U. A. A., Umar, A. A., Aziz, S., Noorazizi
Format:	Article
Language:	English
Published:	UNIVERSITI TEKNIKAL MELAKA 2018
Subjects:	TA213-215 Engineering machinery, tools, and implements
Online Access:	http://eprints.uthm.edu.my/7211/ http://eprints.uthm.edu.my/7211/1/J14194_605818b1a33ebf1d76b6bb0274522699.pdf

Similar Items

Effect of cutting parameters on surface roughness in dry drilling of AISI D2 tool steel by using Taguchi Method
by: M.H. Osman1, M.H. Osman1, et al.
Published: (2018)

Analysis of surface integrity and formation of material side flow in dry and wet machining of aluminum alloy
by: A. B., Hadzley, et al.
Published: (2018)

Q-switched fiber laser employing a passive polarization-maintaining thulium-doped fiber as a saturable absorber
by: Al-Alimi, A.W., et al.
Published: (2022)

Merekabentuk dan menilai peralatan serbaguna untuk ujikaji keseimbangan daya, roda tenaga dan peluncuran
by: Mohd Khathri, Akasyah
Published: (2004)

A comparative study on image compression method using stand-alone DWT techniques and hybrid of DWT with huffman coding technique for WSN application
by: Hussin, Mumtaz Anwar, et al.
Published: (2002)

Physical Properties of New Formulation of Hybrid Nanofluid-based Minimum Quantity Lubrication (MQL) from Modified Jatropha Oil as Metalworking Fluid
by: Sabri, Ainaa Mardhiah, et al.
Published: (2023)

The optimization study on the tool wear of carbide cutting tool during milling Carbon Fibre Reinforced (CFRP) using Response Surface Methodology (RSM)
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2018)

Interactive craft activities – elevating special needs education learning tools with “Craft Interactive Teaching Approach"
by: Maaruf, Siti Zuraida, et al.
Published: (2021)

Content comparative investigation on tool wear during end milling of AISI H13 steel with different tool path strategies
by: Adesta, Erry Yulian Triblas, et al.
Published: (2017)

Study on machinability effect of surface roughness in milling kenaf fiber reinforced plastic composite (unidirectional) using response surface methodology
by: Harun, Azmi, et al.
Published: (2016)

Micro-electro discharge machining of nonconductive zirconia ceramic: investigation of MRR and recast layer hardness
by: Banu, Asfana, et al.
Published: (2014)

Effect of sintering temperature on density, hardness and tool wear for alumina-zirconia cutting tool
by: A. B., Hadzley, et al.
Published: (2019)

Step-NC code generator for drilling operation using GEN-M
by: Zamri Tan, Nurul Zakiah
Published: (2012)

Comparison of dry and cryogenic machining on chip formation and coefficient of friction in turning AISI 4340 alloy steel
by: A. Raof, Natasha, et al.
Published: (2014)

Optimization of milling carbon fiber reinforced plastic using RSM
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2017)

Optimization of milling carbon fibre reinforced plastic under chilled air machining
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2017)

Material characterization of a doped triangular silicon nanowire using raman spectroscopy
by: Za'bah, Nor Farahidah, et al.
Published: (2018)

Efficient dressing of the wheel in ELID grinding by controllable voltage with force feed back
by: Saleh, Tanveer, et al.
Published: (2010)

Optical switches for large core diameter optical fibers (POF & PCF)
by: Bhuiyan, Moinul, et al.
Published: (2004)

Disturbance decoupled fault reconstruction using sliding mode observers
by: Kok, Yew Ng, et al.
Published: (2008)

Manufacturing management: from basic machining to quality product
by: Adesta, Erry Yulian Triblas
Published: (2011)

Tetragonal and monoclinic phase transformation of ZTA-MgO ceramic cutting tool by machining process
by: Mohd Ali, Afifah, et al.
Published: (2017)

Influence of sintering temperature on density, hardness, shrinkage and microstructure of alumina-zirconia cutting tool
by: A. A., Anis, et al.
Published: (2021)

Optimization of Glutathione (GSH) from selected Malaysian local fruit by ultrasonic method
by: Arif, Afraha Baiti, et al.
Published: (2010)

Isolation of Reduced Glutathione (GSH) from local fruits by mechanical methods
by: Jamal, Parveen, et al.
Published: (2010)

Effect of homogenization in breaking protein-carotenoid complexes for releasing active compounds
by: Jamal, Parveen, et al.
Published: (2011)

Optimization of Glutathione (GSH)production from selected Malaysian local fruits by ultrasonic method
by: Jamal, Parveen, et al.
Published: (2011)

Friction and wear analysis of ceramic cutting tool made from Alumina-Zirconia-Chromia
by: Azhar, Anis Afuza, et al.
Published: (2020)

Machinability study on milling kenaf fiber reinforced plastic composite materials using the design of experiments
by: Harun, Azmi, et al.
Published: (2018)

The application of rapid prototyping technology and FMEA quality tool in the development of automotive component
by: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Published: (2009)

The study on the aspect ratio of Atomic Force Microscope (AFM) measurements for Triangular Silicon Nanowire
by: Za'bah, Nor Farahidah, et al.
Published: (2013)

State of the art report of waste tyre in civil engineering application / Lenny A. Rahman
by: A. Rahman, Lenny
Published: (2007)

Study on the plasticiser type for biobased microcrystalline cellulose filled polylactic acid composite
by: Pang, Ming Meng, et al.
Published: (2018)

The effect of varying cutting speeds on tool wear during conventional and Ultrasonic Assisted Drilling (UAD) of Carbon Fibre Composite (CFC) and titanium alloy stacks
by: Dahnel, Aishah Najiah, et al.
Published: (2016)

Artificial intelligence model to predict surface roughness of Ti-15-3 alloy in EDM process
by: Khan, Md. Ashikur Rahman, et al.
Published: (2011)

Fabrication and machining performance of powder compacted alumina based cutting tool
by: Abu Bakar, Hadzley, et al.
Published: (2018)

Effect of pressure on density, porosity and flexural strength during cold isostatic press of alumina-ysz chromia cutting too
by: Norfauzi, T., et al.
Published: (2021)

Design of a plastic injection mold (8 cavities) / Muhammad Fadzli Abdul Rahman and Md Zulkhairi Ismail
by: Abdul Rahman, Muhammad Fadzli, et al.
Published: (2001)

Machining and Tool Wear Mechanisms during Machining Titanium Alloys
by: Islam, Mohammad Nazrul, et al.
Published: (2013)

Tool wear analysis in end milling of advanced ceramics with TiAlN and TiN coated carbide inserts
by: Moola, Mohan, et al.
Published: (2012)