Friction and wear analysis of ceramic cutting tool made from
Alumina-Zirconia-Chromia

QR Code

Friction and wear analysis of ceramic cutting tool made from Alumina-Zirconia-Chromia

This research focused on the friction and wear analysis of ceramic cutting tool made from Al2O3, ZrO2 and Cr2O3. 80 wt% of Al2O3 and 20 wt% of ZrO2 compacts were prepared by ball milling process with Cr2O3 addition at the variation of 0.2, 0.4, 0.6 and 0.8 wt%. Each sample was pressed by C...

Full description

Bibliographic Details
Main Authors:	Azhar, Anis Afuza, Abu Bakar, Mohd Hadzley, Tamin, Norfauzi, Azlan, Umar Al-Amani, Hassan, Muhammad Hafiz
Format:	Article
Language:	English
Published:	Malaysian Tribology Society (MYTRIBOS) 2020
Subjects:	TP200-248 Chemicals: Manufacture, use, etc.
Online Access:	http://eprints.uthm.edu.my/7207/ http://eprints.uthm.edu.my/7207/1/J14190_e7285e4a03e74315242b5ecb57e7ef07.pdf

Similar Items

Influence of sintering temperature on density, hardness, shrinkage and microstructure of alumina-zirconia cutting tool
by: A. A., Anis, et al.
Published: (2021)

Analysis of particles size distribution on the agglomeration and shrinkage of alumina-zirconia compacts
by: A. A., Afuza, et al.
Published: (2020)

Effect of sintering temperature on density, hardness and tool wear for alumina-zirconia cutting tool
by: A. B., Hadzley, et al.
Published: (2019)

Effect of pressure on density, porosity and flexural strength during cold isostatic press of alumina-ysz chromia cutting too
by: Norfauzi, T., et al.
Published: (2021)

Fabrication and machining performance of powder compacted alumina based cutting tool
by: Abu Bakar, Hadzley, et al.
Published: (2018)

Effect of hydraulic pressure on hardness, density, tool wear and surface roughness in the fabrication of alumina based cutting tool
by: M. M., Faiz, et al.
Published: (2018)

The development of ceramic insert of alumina toughened by zirconia and copper
by: Nurfatini, Zolkafli
Published: (2017)

The development of Zirconia and Copper toughened Alumina ceramic insert
by: Nur Amalina, Sabuan, et al.
Published: (2018)

Wear Resistance Performance Of Zirconia Toughened Alumina (ZTA) Cutting Tool Added With MgO and CeO2
by: Ali, Afifah Mohd.
Published: (2016)

The relationship of cutting chip type, length and thickness to wear of Zirconia Toughened Alumina Added with Magnesium Oxide (ZTA-MgO) cutting tool
by: Mohd Ali, Afifah, et al.
Published: (2018)

Wear of zirconia-dispersed alumina at ambient temperature, 140C and 250C
by: Carter, Geoffrey, et al.
Published: (2006)

Chlorine-induced high temperature corrosion of HVAF-sprayed Ni-based alumina and chromia forming coatings
by: Sadeghimeresht, Esmaeil, et al.
Published: (2018)

Study on tool wear and tool life during milling JFRP using uncoated carbide cutting tool
by: Rashid, Mohammed Abdur N., et al.
Published: (2018)

Influence of cutting parameters on chatter and tool wear during end milling of stainless steel conducted on VMC
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Comparison of zirconia toughened alumina fracture toughness obtained from Vickers indentation by applying various equations
by: Roslan, Alida, et al.
Published: (2019)

Wear analysis of Silicon Nitride (Si3N4) cutting tool in dry machining of T6061 Aluminium Alloy
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2013)

A comparative study on flank wear of ceramic and Tungsten carbide inserts during high speed machining of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2018)

Material removal rate of zirconia in electro discharge micromachining
by: Asfana, Banu, et al.
Published: (2015)

Developement of ceramic cutting insert of alumina (Al2O3) and zirconia / zirconium oxide (ZrO2) for turning tool steel
by: Shamsudin, Zuraidy
Published: (2007)

Effect of dispersants on microstructures of nano alpha alumina developed from aluminium dross waste
by: Sofian, Anis Sofia, et al.
Published: (2015)

Wear behaviour of surface alloyed duplex stainless steel containing SiC ceramic particles
by: Paijan, Lailatul Harina, et al.
Published: (2017)

Investigation of the influence of chatter on tool wear
by: Amin, A. K. M. Nurul, et al.
Published: (1987)

Effects of TiO2 addition on the phase, mechanical properties, and microstructure of zirconia-toughened alumina ceramic composite
by: Manshor, Hanisah, et al.
Published: (2014)

Performance properties optimization of triaxial ceramic-palm oil fuel ash by employing Taguchi design and flower pollination algorithm
by: Zainudin, Azlan
Published: (2018)

Role of MgO nanoparticles on zirconia-toughened alumina-5 wt-% CeO2 ceramics mechanical properties
by: Rejab, Nik Akmar, et al.
Published: (2016)

Friction stir welding of dissimilar metal
by: Sahidi, Sujanuriah
Published: (2013)

Fabrication and machining performance of ceramic cutting tool based on the Al2O3-ZrO2-Cr2O3 compositions
by: T., Norfauzi, et al.
Published: (2019)

Wear And Friction On Gimbal Sealant
by: Ibrahim, Illuni Islamiah
Published: (2018)

Utilizing laser cutting method in men’s custom-made casual wear / Mohd Ariff Habit
by: Habit, Mohd Ariff
Published: (2015)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
by: Shaha, Sugrib Kumar, et al.
Published: (2011)

Improving machining performance using alumina powder-added dielectric during electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Effect of titania and magnesia on the physical properties of zirconia toughened alumina
by: Manshor, Hanisah, et al.
Published: (2016)

Neutron Diffraction of Zirconia-Dispersed Alumina with increasing stress and temperature
by: Carter, Geoffrey, et al.
Published: (2008)

An Electrochemical Method to Assess the Chromium Volatility of Chromia-Forming Metallic Interconnect for SOFCs
by: Jiang, San Ping, et al.
Published: (2006)

Reducing electrode wear ratio using cryogenic cooling during electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2009)

Investigation of the mechanism of chatter formation during metal cutting process
by: Amin, A. K. M. Nurul
Published: (1983)

Wear and frictional performance of polymeric composites aged in various solutions
by: Yousif, B.F., et al.
Published: (2011)

High wear Resistant Ceramic Cutting inserts With Enhanced Toughness For High-Speed Machining
by: Ahmad, Zainal Arifin, et al.
Published: (2016)

The effects of sliding parameters on dry wear characteristics of Ti-6Al-4V alloy
by: Mohammed , Baba Ndaliman, et al.
Published: (2015)