The influence of slag and PSAC on the wear resistance of composite aluminium

QR Code

The influence of slag and PSAC on the wear resistance of composite aluminium

This research involves the fabrication of aluminum composite by using Palm Shell Activated Carbon (PSAC) and Boiler Slag as reinforcements. The method used is powder metallurgy. For aluminum composite fabrication process, set compaction pressure of 200 MPa and sintering temperature was at 500°c and...

Full description

Bibliographic Details
Main Author:	Sulaiman, Zulkifli
Format:	Thesis
Language:	English English
Published:	2013
Subjects:	TA Engineering (General). Civil engineering (General) TA401-492 Materials of engineering and construction. Mechanics of materials
Online Access:	http://eprints.uthm.edu.my/6839/ http://eprints.uthm.edu.my/6839/1/24p%20ZULKIFLI%20SULAIMAN.pdf http://eprints.uthm.edu.my/6839/2/ZULKIFLI%20SULAIMAN%20WATERMARK.pdf

Similar Items

The influence of slag and PSAC on the wear resistance of composite aluminium
by: Sulaiman, Zulkifli
Published: (2013)

Effect Of Heat Treatment And Equal Channel Angular Pressing On The Microstructures, Hardness And Wear Resistance Of A356 Aluminium Alloy With Tib2
by: Syukron, Muhammad
Published: (2016)

Wear of aluminium matrix composite – effects of reinforcement combination
by: Maleque, Md. Abdul, et al.
Published: (2011)

Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
by: Mohd Harun, Dalila
Published: (2020)

Influence of deposition parameter to wear behaviour of tungsten carbide-nickel (WC-Ni) high velocity oxyfuel (HVOF) coating
by: Abdul Patar, Mohd Affifudin, et al.
Published: (2018)

Investigation on the plasticity accumulation of Ti-6Al-4V fretting wear by decoupling the eﬀects of wear and surface proﬁle in ﬁnite element modelling
by: Mohd Tobi, A.L., et al.
Published: (2017)

Cold compression in direct recycling of aluminium 6061
by: Chan, Boon Loong
Published: (2016)

Effect of thermal ageing on the scratch resistance of natural-fibre-reinforced epoxy composites
by: Ugochukwu, Solomon, et al.
Published: (2021)

Performance Evaluation Of Steel Slag As Natural Aggregates Replacement In Asphaltic Concrete [TA445.5. T314 2008 f rb].
by: Teoh, Cherh Yi
Published: (2008)

Abrasive wear failure analysis of tungsten carbide hard facing on carbon steel blade
by: Mohd Tobi, A. L., et al.
Published: (2017)

Effect of sintering temperature on density, hardness and tool wear for alumina-zirconia cutting tool
by: A. B., Hadzley, et al.
Published: (2019)

Aluminium recycling activity on construction site: Malaysia case study
by: Rakiman, Umol Syamsyul, et al.
Published: (2017)

To develop a new mineral carbonation process that have a high efficiency in CO2 absorption into industry slag using low energy mechanical milling
by: Selamat, Siti Norhana
Published: (2020)

Optimization of hot press forging parameters in direct recycling of aluminium chip (AA 6061)
by: Lajis, Mohd Amri, et al.
Published: (2014)

Utilization Of Electric Arc Furnace Steel Slag As Partial Replacement Of Raw Materials In Ceramic Tile
by: Teo, Pao Ter
Published: (2016)

The Effect Of Alloying Elements On Wear Behaviour Of Ni-Al [TA483. I98 2004 f rb] [Microfiche 7664].
by: Ishak, Mohamad Izha
Published: (2004)

Value creating activity from aluminium recycling on metal scrap collector site: Malaysia case study
by: Rakiman, Umol Syamsyul, et al.
Published: (2018)

Effect of operating temperature on direct recycling aluminium chips (AA6061) in hot press forging process
by: Yusuf, Nur Kamilah, et al.
Published: (2014)

Fatigue life and mechanical behaviour of aluminium alloy aa6061 chips prepared by hot extrusion process
by: Rady, Mohammed Hussien
Published: (2019)

Evolution of plasticity-based wear damage in gross sliding fretting of a Ti-6Al-4V non-conforming contact
by: Mohd Tobi, A.L., et al.
Published: (2017)

A new approach of direct recycling of aluminium alloy chips (AA6061) in hot press forging process
by: Yusuf, Nur Kamilah
Published: (2013)

Wear behavior and mechanical properties of al-based FGM
by: Mahli, Maximus Kohnizio
Published: (2021)

Relating fractographic analysis to yield strength of novel X7475 (Al–Zn–Mg–Cu) alloys produced by recycling aluminium beverage cans
by: Kazeem, Abubakar, et al.
Published: (2020)

A comparative study on wear and corrosion behaviour of tungsten carbide-nickel (Wc-Ni) and tungsten carbide-cobalt (Wc-Co) high velocity oxy-fuel (HVOF) for carbon steel blade
by: Ahmad, Noor Aqilah
Published: (2017)

Forward problem solving for non-invasive electrical resistance tomography system
by: Abdul Wahab, Yasmin, et al.
Published: (2018)

Pembangunan Konkrit Ringan Menggunakan Polisterena, Serbuk Aluminium Dan Kayu Dalam Kejuruteraan Awam [TA439. P747 2004 f rb] [Microfiche 7540].
by: Poh, Koon Poo
Published: (2004)

Impact resistance of foamed concrete slab and its modifications subjected to hemispherical impactor
by: Hadipramana, Josef
Published: (2015)

Processing routes for graphene composites
by: Roslan, Muhammad Sufi, et al.
Published: (2020)

Water absorption and salt attack resistance of coal ash brick made of different percentage of foam content
by: Ismail, Sushilawati
Published: (2014)

Numerical investigation on reduced moment resistance and increased reinforcement spacing in reinforced concrete wall subjected to blast load
by: Seman, M. A., et al.
Published: (2022)

A preliminary study of turning of composite
by: Hassan, Nurhafizzah
Published: (2008)

Graphite immobilisation in glass composite materials
by: Mayzan, Mohd Zul Hilmi
Published: (2015)

EBB337 Advanced Materials And Composites 2024
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2024)

Microstructure Analysis, Mechanical Properties And Corrosion Behaviour Of Cryorolled Aluminium 1100 Alloy With Different Heat Treatment
by: Zakaria, Siti Aminah
Published: (2018)

EBB 524-3 COMPOSITE MATERIALS MAY 05.
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2005)

EBB 524-3 - COMPOSITE MATERIALS NOV 2008
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2008)

Experimental study on ballistic resistance of sandwich panel protection structure with kenaf foam as a core material against small arm bullet
by: Zainol Abidin, Mohamad Hafiz, et al.
Published: (2013)

EBB 524-3 COMPOSITE MATERIALS OCT-NOV 07.
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2007)

EBB 524-3 COMPOSITE MATERIALS OCT-NOV 06.
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2006)

Oblique impact behavior of unidirectional natural fiber reinforced composites
by: Salim, Yusuf, et al.
Published: (2018)