Effect of drill point angle on surface integrity when drilling titanium alloy

QR Code

Effect of drill point angle on surface integrity when drilling titanium alloy

Surface integrity of machined component is of major importance for the reliability and safety requirements during in service especially for the aerospace applications. This paper presents an investigation on the effect of drill geometry on the surface integrity of drilled hole of Ti-6AL-4V during dr...

Full description

Bibliographic Details
Main Authors:	Murad, Muhamad Nasir, Sharif, S., Rahim, E. A., Riva, R.
Format:	Article
Language:	English
Published:	Trans Tech Publications 2014
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://eprints.uthm.edu.my/5489/ http://eprints.uthm.edu.my/5489/1/AJ%202018%20%28201%29.pdf

Similar Items

Performance evaluation of uncoated and coated carbide tools when drilling titanium alloy
by: Abd. Rahim, Erween
Published: (2005)

Performance evaluation of uncoated and coated carbide tools when drilling titanium alloy
by: Abd. Rahim, Erween
Published: (2005)

Effect of drill geometry of uncoated tool when drilling titanium alloy, Ti-6Al-4V
by: Rashiddy Wong, Freddawati
Published: (2008)

Performance of coated- and uncoated-carbide tools when drilling titanium alloy—Ti–6Al4V
by: Sharif, Safian, et al.
Published: (2007)

Investigation on Tool Life and Surface Integrity when Drilling Ti-6Al-4V and Ti-5Al-4V-Mo/Fe
by: Abd. Rahim, Erween, et al.
Published: (2006)

Experimental investigation on friction drilling of titanium alloy
by: Dehghan, Shayan, et al.
Published: (2018)

An analysis of surface integrity when drilling inconel 718 using palm oil and synthetic ester under, MQL condition
by: A. Rahim, Erween, et al.
Published: (2011)

Investigation of tool life and surface integrity when drilling Ti-6A1-4V and Ti-5A1-4V-Mo/Fe.
by: Abd. Rahim, Erween, et al.
Published: (2006)

Air-Drill With Accelerometer And Microphone For Composite Drilling Application
by: Wei Tong, Koh
Published: (2022)

Effect Of Twist Drill Geometry And Drilling Parameters On Thrust Force In Single-Shot Drilling Of Stack-Up Material
by: Chim, Yi Shen
Published: (2017)

Effect of cutting parameters on the hole diameter and surface roughness for dry drilling of aluminum alloy 6061
by: Ahamed, Ahmad Fauzi
Published: (2010)

Inspection Of Drill Bit Point Angle Using Image Processing Method
by: Ahmad Yusni, Amira Syuhadah
Published: (2018)

Tool failure modes and wear mechanism of coated carbide tools when drilling Ti-6AI-4V
by: Rahim, E. A., et al.
Published: (2007)

Evaluation of wear mechanisms of coated carbide tools when face milling titanium alloy
by: Jawaid, A., et al.
Published: (2000)

Optimization of drill bit geometries for minimum thermal damage in bone drilling
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2024)

A study of the effect of palm oil as MQL lubricant on high speed drilling of titanium alloys
by: Rahim, E. A., et al.
Published: (2011)

Chip Formation When Drilling AISI 316L Stainless Steel using Carbide Twist Drill
by: Sultan, A., et al.
Published: (2015)

Optimization of Electro Discharge Machining Parameters for Drilling Titanium in Small Holes Using Taguchi Method
by: Hazami, Che Hussain, et al.
Published: (2014)

Surgical drill bit design and thermomechanical damage in bone drilling: A review
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2021)

The Use Of Response Surface Methodology (RSM) To Optimize The Twist Drill Geometry In Single Shot Drilling Of Stacked Alumina-Carbon Composite Layer
by: Mohd Adnan, Muhammad Aimi
Published: (2018)

Drilling of bone: thermal osteonecrosis regions induced by drilling parameters
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2019)

Multi-objective optimization of surgical drill bit to minimize thermal damage in bone-drilling
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2019)

Geometrical integrity of microholes drilled by conventional and micro electrical discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Influence of machining parameters on temperature when drilling carbon fiber reinforced polymer (CFRP) using coated diamond drills
by: Konneh, Mohamed, et al.
Published: (2015)

Drilling of bone: Effect of drill bit geometries on thermal osteonecrosis risk regions
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2019)

Quality And Performance Analysis Of Drill Tools
by: Subramonian, Sivarao
Published: (2005)

Control of automatic drilling machine by PLC
by: Rahman , Md Mozasser, et al.
Published: (2011)

Wear Analysis On Different Customized Twist Drill Bit Designs In Drilling Cfrp Panel
by: Hashimi, Nur Hatin Raihana
Published: (2021)

Three dimensional finite element modeling, when drilling of Ti-6Al-4V
by: Abd Rahim, Erween, et al.
Published: (2017)

An experimental investigation on drilling of aluminum alloy (Al 7075) using high speed steel cutting tools
by: Abd Halim, Nor Farah Huda, et al.
Published: (2020)

Experimental analysis on drilling process of composite laminates
by: Sivasankaran, Praveena Nair
Published: (2008)

Effect of material thickness on Duration, hole characteristics, and drilling mechanism on micro-laser drilling
by: Haneef, Mohd Sabki
Published: (2023)

High aspect ratio micro-EDM drilling with nano surface finish
by: Ali , Mohammad Yeakub, et al.
Published: (2016)

Performance evaluation of uncoated carbide tool in high speed drilling of Ti6Al4V
by: Abd. Rahim, Erween, et al.
Published: (2008)

Sem Observations On Wear Mechanism Of Tin-Coated Hss Twist Drills When Drilling Mild Steel
by: Talib, R. J., et al.
Published: (2004)

Optimization Of Customized Tetra-Flute Drill Reamer For A Better Hole Quality In Single Shot Drilling Of Cfrp Composite Laminate
by: Choo, Then Xiang
Published: (2021)

Optimization drilling process of glass fiber reinforced plastics
by: Norhaida, Mohamad Noor
Published: (2008)

Experimental analysis on drilling process of CFRP composite laminates
by: Latifah, Md Yusoff
Published: (2008)

Surface integrity evaluation on titanium alloy after EDM machining using different graphite electrodes
by: Mat Jusoh, Mazlan
Published: (2010)

Micro-drilling of metallic materials for microsystems technology
by: Ali, Mohammad Yeakub
Published: (2008)