An investigation on chemical bubble column using ultrasonic tomography for imaging of gas proﬁles

QR Code

An investigation on chemical bubble column using ultrasonic tomography for imaging of gas proﬁles

In this paper, we carried out a tomographic investigation of a chemical bubble column using ultrasonic sensor. The ultrasonic tomography sensing array was constructed to operate in transceiver-mode and was clamped on the exterior circumference of the column. The time-of-ﬂight and arrival-time analys...

Full description

Bibliographic Details
Main Authors:	Rahiman, M.H.F., Rahim, R.A., Rahim, H.A., Mohamad, E.J., Zakaria, Z., Muji, S.Z.M.
Format:	Article
Language:	English
Published:	Elsevier Science Ltd 2014
Subjects:	RC Internal medicine TA401-492 Materials of engineering and construction. Mechanics of materials
Online Access:	http://eprints.uthm.edu.my/4226/ http://eprints.uthm.edu.my/4226/1/AJ%202017%20%28127%29%20An%20investigation%20on%20chemical%20bubble%20column.pdf

Similar Items

Tomography systems and sensor applications velocity measurement of gas bubbles flow in vertical water column using ultrasonic sensor
by: Syed Yahya, Syed Redha, et al.
Published: (2018)

Modelling ultrasonic sensor for gas bubble proﬁles characterization of chemical column
by: Rahiman, M.H.F., et al.
Published: (2013)

Simulation and experimental study of the sensor emitting frequency for ultrasonic tomography system in conducting pipe
by: Goh, Chiew Loon, et al.
Published: (2017)

An investigation on chemical bubble column using ultrasonic tomography for imaging of gas profiles
by: Rahiman, Mohd Hafiz Fazalul, et al.
Published: (2014)

Forward problem solving for non-invasive electrical resistance tomography system
by: Abdul Wahab, Yasmin, et al.
Published: (2018)

Properties of a new insulation material glass bubble in geopolymer concrete
by: Shahedan, Noor Fifinatasha, et al.
Published: (2021)

Intensity profile measurement for carbon steel pipe using gamma-ray tomography
by: Y.S., Susiapan, et al.
Published: (2017)

Behavior of concrete-filled pvc tube columns under axial load
by: Abdulrazzaq Azeez, Alyaa
Published: (2018)

A study of the effect of palm oil as MQL lubricant on high speed drilling of titanium alloys
by: Rahim, E. A., et al.
Published: (2011)

Delamination in fiberglass pre-impregnated laminated composites from ultrasonic a-scan signal using artificial intelligence
by: Mahmod, Muhammad Faisal
Published: (2018)

Investigation on the plasticity accumulation of Ti-6Al-4V fretting wear by decoupling the eﬀects of wear and surface proﬁle in ﬁnite element modelling
by: Mohd Tobi, A.L., et al.
Published: (2017)

Influence of substrate annealing on inducing Ti3+ and oxygen vacancy in TiO2 thin films deposited via RF magnetron sputtering
by: Abdullah, S.A., et al.
Published: (2018)

Hydrophobicity properties of graphite and reduced graphene oxide of the polysulfone (PSf) mixed matrix membrane
by: Akhair, S. H. M., et al.
Published: (2018)

Preparation of Aniline Dimer-COOH modified M=magnetite (Fe3O4) nanoparticles by ultrasonic dispersion method
by: Taka, Zakiyyu Ibrahim, et al.
Published: (2018)

Experimental validation of a theoretical model for flexural modulus of elasticity of thin cement composite
by: Hossain, M.Z., et al.
Published: (2011)

The influence of density, compressive strength and thermal conductivity under variety percentage of glass bubble in geopolymer concrete
by: Shahedan, Noor Fifinatasha, et al.
Published: (2021)

Abrasive wear failure analysis of tungsten carbide hard facing on carbon steel blade
by: Mohd Tobi, A. L., et al.
Published: (2017)

Numerical investigation on reduced moment resistance and increased reinforcement spacing in reinforced concrete wall subjected to blast load
by: Seman, M. A., et al.
Published: (2022)

Thermal and activation energy of renewable polymer after UV irradiation
by: Mat Hassan, Nik Normunira, et al.
Published: (2016)

Solidification, microstructure and mechanical properties of Mg-2.8Nd-1.5Gd-0.5Zn-0.5Zr cast alloy with erbium addition
by: Ahmad, R., et al.
Published: (2018)

Event-driven applications for hard-field tomography software modelling of forward and inverse solutions
by: Goh, C.L., et al.
Published: (2017)

Effect Of Combination Ultrasonic And Ball Milling Techniques Of Fillers Dispersion On Mechanical And Pgysical Properties Of Natural Rubber Latex Films
by: Hamran, Noramirah
Published: (2018)

Microstructure analysis of tungsten carbide hardfacing on carbon steel blade
by: Nagentrau, M., et al.
Published: (2017)

Electrophoretic deposition of Ba0.5Sr0.5Co0.8Fe0.2O3−∞SDC carbonate composite coating on solid oxide fuel cell interconnect
by: Tan, K. H., et al.
Published: (2018)

A review on electrical capacitance tomography sensor development
by: Abd. Rahman, Noor Amizan, et al.
Published: (2015)

Effect of Water to Cement Ratio and Replacement Percentage of Recycled Concrete Aggregate on the Concrete Strength
by: Khalid, Faisal Sheikh, et al.
Published: (2020)

Image reconstruction of metal pipe in electrical resistance tomography
by: Ridzuan Aw, Suzanna, et al.
Published: (2017)

Mode i stress intensity factors of slanted cracks
by: Ismail, Al Emran, et al.
Published: (2017)

Effect of thermal ageing on the scratch resistance of natural-fibre-reinforced epoxy composites
by: Ugochukwu, Solomon, et al.
Published: (2021)

Properties and environmental impact from mosaic sludge industry incorporated into fired clay bricks
by: Abdul Rahim, Ahmad Shayuti
Published: (2016)

Oblique impact behavior of unidirectional natural fiber reinforced composites
by: Salim, Yusuf, et al.
Published: (2018)

Multi-walled carbon nanotubes grow under low pressure hydrogen, air, and argon ambient by arc discharge plasma
by: Roslan, Muhammad Sufi, et al.
Published: (2017)

Modelling ultrasonic sensor for gas bubble profiles characterization of chemical column
by: Rahiman, Mohd Hafiz Fazalul, et al.
Published: (2013)

Influence of deposition parameter to wear behaviour of tungsten carbide-nickel (WC-Ni) high velocity oxyfuel (HVOF) coating
by: Abdul Patar, Mohd Affifudin, et al.
Published: (2018)

Modulation of Sn concentration in ZnO nanorod array: intensification on the conductivity and humidity sensing properties
by: Ismail, A. S., et al.
Published: (2018)

Fabrication and machining performance of ceramic cutting tool based on the Al2O3-ZrO2-Cr2O3 compositions
by: T., Norfauzi, et al.
Published: (2019)

Effect of sintering temperature on density, hardness and tool wear for alumina-zirconia cutting tool
by: A. B., Hadzley, et al.
Published: (2019)

Fatigue performance of thermal spray coatings on carbon steel: a review
by: M. Halmi, M. A., et al.
Published: (2019)

Evolution of plasticity-based wear damage in gross sliding fretting of a Ti-6Al-4V non-conforming contact
by: Mohd Tobi, A.L., et al.
Published: (2017)

Failure mechanism of prepacked concrete
by: Abdul Awal, A. S. M.
Published: (1988)