The optimisation of processing conditions and the effect of nanoclay towards snap fit samples.

QR Code

The optimisation of processing conditions and the effect of nanoclay towards snap fit samples.

This research is about the optimisation the injection moulding processing condition to control shrinkage and warpage for the snap fit product throughout the Taguchi method in practical injection moulding. At this try out, the selected processing conditions were barrel temperature, holding pressure,...

Full description

Bibliographic Details
Main Authors:	Othman, M.H., Ibrahim, M.H.I., Amin, A.M., Y,Hashim, M., Ng, C.H., Osman, S.A., Marwah, O.M.F., Shaari, M.F., Rafai, N.H., Johar, M.A.
Format:	Article
Language:	English
Published:	Academic Publications Ltd 2018
Subjects:	TP1080-1185 Polymers and polymer manufacture
Online Access:	http://eprints.uthm.edu.my/3589/ http://eprints.uthm.edu.my/3589/1/AJ%202019%20%28142%29.pdf

Similar Items

Multiple responses optimisation in injection moulding parameter for polypropylene-nanoclay-gigantochloa scortechinii via taguchi method
by: Khamis, S Z, et al.
Published: (2019)

Preparation of injection moulding processing for high density polyethylene via moldflow advisor 2015 simulation
by: Othman, M.H., et al.
Published: (2018)

Critical powder loading and the rheology of nanosized cemented carbide with titanium carbide as grain growth inhibitor for injection molding
by: Shahbudin, S.N.A., et al.
Published: (2018)

Optimization of polymer blend electrolytes with tuneable conductivity potentials
by: Nurhaziqah, A.M.S., et al.
Published: (2023)

Optimization of injection molding parameters for WC-TaC-6Co
by: Prathabrao, M., et al.
Published: (2019)

Investigation of clothes recycling as colouring agent for polypropylene-nanoclay nanocomposites
by: Othman, Mohd Hilmi, et al.
Published: (2018)

Surface properties of alginate/chitosan biofilm for wound healing application
by: Idris, M.I., et al.
Published: (2020)

The modelling of processing conditions for polypropylene-nanoclay integral hinges at high heat exposure
by: Othman, Mohd Hilmi
Published: (2015)

Parameter optimization of metal injection moulding: a review
by: Prathabrao, M, et al.
Published: (2018)

Dynamic mechanical analysis and morphology of petroleum-based and bio-epoxy foams with wood filler
by: Alzomor, A., et al.
Published: (2021)

Removal of bisphenol A from aqueous media using a highly selective adsorbent of hybridization cyclodextrin with magnetic molecularly imprinted polymer
by: Mamman, S., et al.
Published: (2021)

Properties of cup lump rubber modified asphalt binder
by: M. Azahar, N., et al.
Published: (2019)

Dynamic mechanical analysis of Dwimatrix Biopolymer from waste oil blended with thermoplastic; LDPE/HDPE
by: M. Rus, A .Z., et al.
Published: (2021)

Parameter optimization of debinding injection moulded Ti-6Al-4V mix with palm stearin and polyethylene
by: Jamaludin, M. I., et al.
Published: (2014)

Tensile property of melt mixing co-polypropylene with waste polymer at different composition ratios
by: Sufian, N. A., et al.
Published: (2018)

Mechanical properties of wood polymer composites (WPCs) after prolonged ultra-violet (UV) irradiation exposure
by: S., N. Afiqah, et al.
Published: (2018)

Investigation of mould design and process parameter optimisation of plastic injection moulding for thin wall part
by: Hussin, Azmee
Published: (2019)

Thermal degradation study of waste polymer matrix polypropylene and polyvinyl chloride as polymer matrix filled rice husk decking structure
by: S., N. Afiqah, et al.
Published: (2018)

Waste polymer blended with copolymer polypropylene to enhance mechanical properties using injection moulding
by: S., N. Afiqah, et al.
Published: (2018)

Simulation of lamination orientation for carbon fiber reinforced polymer as a wrapping structure on piping system
by: M. Letchumanan, Shaktivell
Published: (2021)

Impact resistance study on rigid polyurethane foam
by: M. F. F., Mohamad, et al.
Published: (2018)

Modelling of integral hinges via CadMould 3d-F injection moulding simulation
by: Othman, M.H., et al.
Published: (2018)

Isolation and identification of polystyrene degrading bacteria from zophobas morio’s gut
by: Kian, Meng Tan, et al.
Published: (2015)

Isolation and identification of polystyrene degrading bacteria from zophobas morio’s gut
by: Tan, Kian Meng, et al.
Published: (2021)

EBP 412-3 - SPECIALITY POLYMERS APRIL-MAY 06.
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2006)

EBP 412-3 POLIMER KHUSUS APRIL-MEI 06.
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2006)

EBP 201-3 SINTESIS POLIMER OKT 04.
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2004)

EBP 202-3 STRUKTUR POLIMER OKT 04.
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2004)

EBP 310-3 PEMPROSESAN PLASTIK OKT-NOV 06.
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2006)

EBP 324-3 DEGRADASI POLIMER & ALAM SEKITAR APRIL-MEI 06.
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2006)

EBP 307E-3 POLYMER RHEOLOGY APR-MEI 06.
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2006)

Komposit Poliester Diperkuat Hibrid Gentian Sabut Kelapa Dan Gentian Kaca [TP1180.P6 H239 2007 f rb].
by: Saaidi, Hanida
Published: (2007)

Preparation And Properties Of New Thermoplastic Elastomer Based On Ethylene Vinyl Acetate (EVA)/ Natural Rubber Blends [TP1180.T5 Y55 2007 f rb].
by: Yong, Mun Kong
Published: (2007)

EBP 103-3 POLYMER ORGANIK CHEMISTRY OCT-NOV 06.
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2006)

EBP 201-3 POLYMER SYNTHESIS OKT-NOV 06.
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2006)

EBP 202-3 POLYMER STRUCTURE OCT-NOV 06.
by: PPKBSM, Pusat Pengajian Kejuruteraan Bahan dan Sumber Mineral
Published: (2006)

Pencirian Dan Sifat-Sifat Komposit Polipropilena (Pp)/Etilena Propilena Diena Monomer (Epdm) Terisi Sludge Kertas [TP1180.P68 S171 2005 f rb] [Microfiche 8548].
by: Salmah, Salmah
Published: (2005)

Toughening Of Epoxy Resin With Modified Liquid Natural Rubbers And Acrylonitrile-Butadiene Liquid Rubbers [TP1180.E6 A136 2005 f rb].
by: Ben Saleh, Abdulali Bashir Ahmed
Published: (2005)

Development Of Multi-Component Degradable Plastics Through The Combination Of The Sago Starch And Polyethylene/Poly (E-Caprolactone) Blends [TP1180.B55 L732 2007 f rb].
by: Lim, Wei Lee
Published: (2007)

IPK 204 - BAHAN ELASTOMER SEPT 03.
by: PPTI, Pusat Pengajian Teknologi Industri
Published: (2003)