Study on the variability of printed documents produced by laserjet
Printers (hp laserjet p3005 printers)

QR Code

Study on the variability of printed documents produced by laserjet Printers (hp laserjet p3005 printers)

This study looks at the variability of prints produced by LaserJet printers. Five HP LaserJet P3005 printers were used to print out a letter consisting of a mixed of letters and numbers at different fonts. Seven duplicates were printed from each printer and compared using a stereomicroscope. Prin...

Full description

Bibliographic Details
Main Author:	Kamaluddin, Mohammad Rahim
Format:	Monograph
Language:	English
Published:	Pusat Pengajian Sains Perubatan, Universiti Sains Malaysia 2011
Subjects:	R Medicine
Online Access:	http://eprints.usm.my/53451/ http://eprints.usm.my/53451/1/MOHAMMAD%20RAHIM%20BIN%20KAMALUDDIN-24%20pages.pdf

Similar Items

Development Of A Portable 3D Printer For Medical Modelling
by: Sin, Chia Ling
Published: (2020)

Nava - Printers in Milan
by: Simionato, Andy, et al.
Published: (2013)

Design and fabrication of printer table
by: Hadianatun Saadiah, Jasni
Published: (2013)

Patient-specific 3D printed models of renal tumours using home-made 3D printer in comparison with commerical 3D printer
by: Liu, D., et al.
Published: (2018)

Design and fabrication of laboratory printer table
by: Noorhidayad, Mohd Noh
Published: (2012)

Proposal:Step by Step Procedures of Scanning Document Directly to Email (Printer Ricoh 907ex)
by: Johari, Mohd Helmi, et al.
Published: (2015)

The Effect of Printing Parameters on Scaffold Structure Using Low-cost 3D Printer
by: Sukindar, Nor Aiman, et al.
Published: (2020)

Utilizing rapid prototyping 3D printer for fabricating flexographic PDMS printing plate
by: Maksud, M. I., et al.
Published: (2016)

A study of printing plate mould development by using 3d printers for micro-flexographic printing process
by: Hassan, S., et al.
Published: (2020)

Henna@Printer / Nurul Atikah Badrol Hisham
by: Badrol Hisham, Nurul Atikah
Published: (2020)

Development of low cost 3D printer
by: Nor Azirah, Arifin
Published: (2017)

An exploration of printing challenges and strategies among Malaysia commercial printers / Noor Azly Mohammed Ali
by: Mohammed Ali, Noor Azly
Published: (2018)

Contribution factors to the success of book printers in surviving book printing industry / Shalida Mohd Rosnan
by: Mohd Rosnan, Shalida
Published: (2016)

An exploration of printing challenges and strategies among Malaysia commercial printers / Noor Azly Mohammed Ali
by: Mohammed Ali, Noor Azly
Published: (2018)

Printing and curing silver conductive ink tracks from modified on-shelf inkjet printer on fabric
by: Khirotdin, Rd Khairilhijra', et al.
Published: (2017)

Assessment of polyaromatic hydrocarbon emissions from laser printers
by: Mullins, Benjamin, et al.
Published: (2013)

Investigation of the effect of print parameter on dimensional accuracy for fused deposition modelling (FDM) 3D printer
by: Nurul Najaa, Sharizal, et al.
Published: (2022)

Study of using three dimensional printer for EDM electrode fabrication
by: Hassan, Noor Haslyena
Published: (2011)

Slicer method comparison using open-source 3D printer
by: Mohd Ariffin, M K A, et al.
Published: (2018)

A printer indexing system for color calibration with applications in dietary assessment
by: Fang, S., et al.
Published: (2015)

Development of stack component for thermoacoustic refrigerator using 3d printer
by: Nor Atiqah, Zolpakar, et al.
Published: (2021)

Waste-to-wealth : From printer toner waste into valuable magnetic materials
by: Nurul Hidayah, Ghazali, et al.
Published: (2021)

Development Of A Small Scale Corexy Type 3D Printer
by: Yeoh, Xing Yuan
Published: (2021)

Hardware improvement of FDM 3D printer: issue of bed leveling failures
by: Arief, Rudi Kurniawan, et al.
Published: (2019)

Environmental impacts of selective laser melting: do printer, powder, or power dominate?
by: Faludi, Jeremy, et al.
Published: (2016)

Analysis and design of control system for desktop size concrete 3D printer
by: Iqbal, A. R., et al.
Published: (2022)

Important criteria for preparation of 3D printer filaments from polymer biocomposites
by: Shamsuri, Ahmad Adlie
Published: (2019)

Development of Alumina Based Feedstock For Fused Deposition Modelling 3D Printer
by: Tan, Roe Djer
Published: (2020)

Development of two-fingered underactuated robot gripper using 3D printer
by: Sadun, Amirul Syafiq, et al.
Published: (2019)

Control Of 3d Printer Using Drone With Autopilot And Raspberry Pi Microcontroller
by: Sam, Jun Kok
Published: (2019)

Design and develop an active mixer extruder for ink based 3D printer
by: Cheah, Choon Kit
Published: (2022)

Continuous data collection of under extrusion in FDM 3D printers for deep-learning dataset
by: Liwauddin, Muhammad Lut, et al.
Published: (2022)

Detection of latent fingermarks on thermal printer paper by dry contact with 1,2-indanedione
by: Patton, Emma, et al.
Published: (2010)

Structural and Magnetic Characteristics Evaluation of Iron Oxide Extracted from Printer Toner Wastes
by: Rodziah, Nazlan, et al.
Published: (2022)

Development of printer nozzle for extruding synthetic biomaterials using fused deposition modeling process
by: Sukindar, Nor Aiman
Published: (2018)

Analysis on temperature setting for extruding polylactic acid using open-source 3D printer
by: Sukindar, Nor Aiman, et al.
Published: (2017)

Analysis of mechanical properties of polylactic acid using a new 3D printer nozzle
by: Sukindar, Nor Aiman, et al.
Published: (2018)

New framework for improving production efficiency by integrating degree of contribution and cost driver for thermal printer
by: Nor Suhadah, Razali, et al.
Published: (2025)

Analysis of mechanical properties of polylactic acid using a new 3D printer nozzle
by: Mohd Ariffin, Mohd Khairol Anuar, et al.
Published: (2018)

Thermal parameter affects on the part built using 3D printer Projet SD 3000
by: Ahmad, M. Syahrir, et al.
Published: (2012)