Air Fuel Mixing Modeling For
Direct And Transfer Port Injection In
Two Stroke Engine

QR Code

Air Fuel Mixing Modeling For Direct And Transfer Port Injection In Two Stroke Engine

Two-stroke engines are commonly found in small transportation units in many South Asian countries. Due to high fuel losses during the scavenging process, the amount of pollution emitted by these two-stroke vehicles is significant. In this study, the details of a gaseous fuel direct injection system...

Full description

Bibliographic Details
Main Author:	Tan, Yee Hern
Format:	Thesis
Language:	English
Published:	2013
Subjects:	TJ1-1570 Mechanical engineering and machinery
Online Access:	http://eprints.usm.my/43979/ http://eprints.usm.my/43979/1/Tan%20Yee%20Hern24.pdf

Similar Items

Design And Performance Analysis Of A Small Two-Stroke Direct Injection Diesel Engine.
by: Loh, Jian Haur
Published: (2011)

Influence of Engine Speed and Injection Timings on In-Cylinder Heat Transfer for Port Injection Hydrogen Fueled Engine
by: M. M., Rahman, et al.
Published: (2010)

Heat Transfer Characteristics in Exhaust Port for Hydrogen Fueled Port Injection Engine A Transient Approach
by: M. M., Noor, et al.
Published: (2011)

Heat transfer of intake port for hydrogen fueled port injection engine: A steady state approach
by: M. M., Rahman, et al.
Published: (2011)

Port Injection Of Biomass Producer Gas From Downdraft Gasifier In A Diesel Engine
by: Hassan, Suhaimi
Published: (2011)

Study Of Air Fuel Ratio On Engine Performance Of Direct Injection Hydrogen Fueled Engine
by: M. M., Rahman, et al.
Published: (2008)

Effect of Air Fuel Ratio on Engine Performance of Single Cylinder Port Injection Hydrogen Fueled Engine: A Numerical Study
by: M. M., Rahman, et al.
Published: (2009)

Heat transfer analysis inside exhaust port for a hydrogen fueled port injection engine
by: Rahman, Md. Mustafizur, et al.
Published: (2012)

Trends of Air Fuel Ratio on Engine Performance of Four Cylinder Direct Injection Hydrogen Fueled Engine
by: M. M., Rahman, et al.
Published: (2010)

Time-averaged Heat Transfer Correlation for Direct Injection Hydrogen Fueled Engine
by: Khalaf I., Hamada, et al.
Published: (2012)

One-dimensional simulation of two stroke hydrogen direct injection linear generator free-piston engine
by: Muhammad Alliff, Rahim
Published: (2010)

Characterization Of The Time-Averaged Overall Heat Transfer In A Direct-Injection Hydrogen-Fueled Engine
by: M. M., Rahman, et al.
Published: (2012)

Modeling and Engine Performance of Direct Injection Hydrogen Fueled Engine
by: M. M., Rahman, et al.
Published: (2009)

Effect Of Gasohol Blends On A Four Cylinder, Port Fuel Injection Engine Performance
by: Amirruddin, Abdul Kadir
Published: (2009)

3-Cylinder gasoline direct injection as opposed to 4-cylinder multi-port fuel injection for lower fuel consumption and NOX emission
by: Mohiuddin, A. K. M., et al.
Published: (2011)

Numerical Investigations on the Port Flow Field of a Two-Stroke Poppet Valve Engine
by: Mohd Razali, Hanipah, et al.
Published: (2016)

Parametric Study Of Instantaneous Heat Transfer Based on Multidimensional Model in Direct-Injection Hydrogen-Fueled Engine
by: Hamada, Khalaf I., et al.
Published: (2013)

Transient in-cylinder gas flow characteristics of single cylinder port injection hydrogen fueled engine
by: Rahman, MM, et al.
Published: (2010)

The impact of air pressure on performance, combustion behavior, and emissions of an air-assisted port fuel injection HCCI engine
by: Dzulkafli, Mohd Firdaus, et al.
Published: (2025)

Direct Injection of Hydrogen, Oxygen, and Water in a Novel Two Stroke Engine.
by: Aris, Ishak, et al.
Published: (2011)

Effect of Air-fuel Ratio on the Combustion Characteristics of Syngas (H2:CO) in Direct-injection Spark-ignition Engine
by: Hogas, F. Y., et al.
Published: (2014)

Effect of Mixture Strength and Injection Timing on Combustion Characteristics of a Direct Injection Hydrogen-Fueled Engine
by: Hamada, Khalaf I., et al.
Published: (2013)

Development of a direct fuel injector for a two-stroke gasoline engine
by: Mohd Ali, Mas Fawzi
Published: (2007)

Intake and exhaust ports flow investigation of 4-stroke SI engine
by: Mohammad Amin, Mohamed
Published: (2010)

Development of a Complete Single Jet Common Rail Injection System Gas Dynamic Model for Hydrogen Fueled Engine with Port Injection Feeding System
by: Kamil, Mohammed, et al.
Published: (2016)

Investigation of Emissions Characteristics of Secondary Butyl Alcohol-Gasoline Blends in a Port Fuel Injection Spark Ignition Engine
by: I. M., Yusri, et al.
Published: (2017)

Perodua Myvi engine fuel consumption map and fuel economy vehicle simulation on the drive cycles based on Malaysian roads
by: Ramdan, Muhammad Iftishah
Published: (2017)

Effect of Fuel Injection Timing of Hydrogen Rich Syngas Augmented With Methane in Direct-Injection Spark-Ignition Engine
by: Hagos, F. Y., et al.
Published: (2017)

Fuel rail for direct injection gaseous engine.
by: Taha, Zahari, et al.
Published: (2006)

Water injection system design for six stroke engine
by: Muhamad Nurzami, Ab Sota
Published: (2012)

Engine Performance, Exhaust Emission And Combustion Analysis Of A 4-Stroke Spark Ignited Engine Using Dual Fuel Injection
by: D., Ramasamy, et al.
Published: (2017)

Development Of Variable Valve Timing Mechanism For Compressed Air Engine
by: Ahmad, Fathul Hazrimy
Published: (2019)

Design and development of piston-controlled intake port for 4-stroke engine
by: Amran, Kaharudin
Published: (2008)

The influence of rice bran oil blended and intake air temperature on combustion behaviours and knocking of single cylinder four stroke direct injection compression ignition engine
by: Norhafana, Mohamed
Published: (2024)

Combustion Characteristics Of Blends Of Kerosene And Cooking Oil At Various Fuel-Air Equivalence Ratio Simulation Approach
by: Kadir, Mohammad ‘Asri
Published: (2021)

Optimization Of Injection Moulding Process For Hdpe Moulded Gear
by: Kassim, Mohd Syahir Mohd
Published: (2015)

Method for controlling multiple-injection of gaseous fuel in a direct injection engine.
by: Sahari, Barkawi
Published: (2005)

Heat transfer and fuel transport in the intake port of a spark ignition engine
by: Colechin, Michael John Farrelly
Published: (1996)

Simulation of direct injection, mixing and combustion of CNG fuel in a single - cylinder engine with different injector orientations using CFD
by: Mohd Azlan Fahmi, Muhammad Azmi, et al.
Published: (2022)

Transient in-cylinder gas flow characteristics of single cylinder port injection hydrogen fueled engine
by: Rahman, Md. Mustafizur, et al.
Published: (2010)