Fast And Accurate Receiver Jitter Tolerance Extrapolation Using The Q-Factor Linear Fitting Method
A performance bit rates of more than 6 Gb/s is deemed as a common standard in high-speed interconnect system in conjunction with the recent enhancement of high-speed serial interface (HSSI). In industry, receiver (Rx) jitter tolerance (JTOL) measurement required to characterize the high-speed interc...
| Main Author: | |
|---|---|
| Format: | Thesis |
| Language: | English |
| Published: |
2017
|
| Subjects: | |
| Online Access: | http://eprints.usm.my/37335/ http://eprints.usm.my/37335/1/ABDUL_RAIS_BIN_ABDUL_RAHIM_24_Pages.pdf |
| _version_ | 1848878164899528704 |
|---|---|
| author | Abdul Rahim, Abdul Rais |
| author_facet | Abdul Rahim, Abdul Rais |
| author_sort | Abdul Rahim, Abdul Rais |
| building | USM Institutional Repository |
| collection | Online Access |
| description | A performance bit rates of more than 6 Gb/s is deemed as a common standard in high-speed interconnect system in conjunction with the recent enhancement of high-speed serial interface (HSSI). In industry, receiver (Rx) jitter tolerance (JTOL) measurement required to characterize the high-speed interconnect. Time required for conventional methods to complete Rx JTOL measurement for low bit error rate (BER) values normally took a week’s time depending on the data rate. In addition, a large number of bits is required to be transmitted hence resulting measurement cost as inefficient. This research project implements a method known as Q-factor linear fitting method to reduce the measurement time of the Rx JTOL at low BER by using high BER data. The result shows that the measurement of Rx JTOL using Q-factor linear fitting method using BER 10-10 data achieved 11x speed-up in comparison to direct measurement of Rx JTOL. The proposed methods of combined different level of BER values and increase more data points of higher BER able to significantly improve the accuracy of the Rx JTOL measurement result. The proposed method is successfully established in the experiment where the results obtained indicated relative error of Rx JTOL using Q-factor linear fitting method of BER 10-10 data are reduced from 9.47% to 3.31% after combining with the BER 10-11 data and relative error for Rx JTOL extrapolation measurement using BER 10-10 data at low temperature (-25˚C) is reduced from 9.47% to 5.43% by increasing the measurement data point from 20 data points to 30 data points |
| first_indexed | 2025-11-15T17:26:59Z |
| format | Thesis |
| id | usm-37335 |
| institution | Universiti Sains Malaysia |
| institution_category | Local University |
| language | English |
| last_indexed | 2025-11-15T17:26:59Z |
| publishDate | 2017 |
| recordtype | eprints |
| repository_type | Digital Repository |
| spelling | usm-373352019-04-12T05:25:05Z http://eprints.usm.my/37335/ Fast And Accurate Receiver Jitter Tolerance Extrapolation Using The Q-Factor Linear Fitting Method Abdul Rahim, Abdul Rais TK1-9971 Electrical engineering. Electronics. Nuclear engineering A performance bit rates of more than 6 Gb/s is deemed as a common standard in high-speed interconnect system in conjunction with the recent enhancement of high-speed serial interface (HSSI). In industry, receiver (Rx) jitter tolerance (JTOL) measurement required to characterize the high-speed interconnect. Time required for conventional methods to complete Rx JTOL measurement for low bit error rate (BER) values normally took a week’s time depending on the data rate. In addition, a large number of bits is required to be transmitted hence resulting measurement cost as inefficient. This research project implements a method known as Q-factor linear fitting method to reduce the measurement time of the Rx JTOL at low BER by using high BER data. The result shows that the measurement of Rx JTOL using Q-factor linear fitting method using BER 10-10 data achieved 11x speed-up in comparison to direct measurement of Rx JTOL. The proposed methods of combined different level of BER values and increase more data points of higher BER able to significantly improve the accuracy of the Rx JTOL measurement result. The proposed method is successfully established in the experiment where the results obtained indicated relative error of Rx JTOL using Q-factor linear fitting method of BER 10-10 data are reduced from 9.47% to 3.31% after combining with the BER 10-11 data and relative error for Rx JTOL extrapolation measurement using BER 10-10 data at low temperature (-25˚C) is reduced from 9.47% to 5.43% by increasing the measurement data point from 20 data points to 30 data points 2017 Thesis NonPeerReviewed application/pdf en http://eprints.usm.my/37335/1/ABDUL_RAIS_BIN_ABDUL_RAHIM_24_Pages.pdf Abdul Rahim, Abdul Rais (2017) Fast And Accurate Receiver Jitter Tolerance Extrapolation Using The Q-Factor Linear Fitting Method. Masters thesis, Universiti Sains Malaysia. |
| spellingShingle | TK1-9971 Electrical engineering. Electronics. Nuclear engineering Abdul Rahim, Abdul Rais Fast And Accurate Receiver Jitter Tolerance Extrapolation Using The Q-Factor Linear Fitting Method |
| title | Fast And Accurate Receiver Jitter Tolerance Extrapolation Using The Q-Factor Linear Fitting Method |
| title_full | Fast And Accurate Receiver Jitter Tolerance Extrapolation Using The Q-Factor Linear Fitting Method |
| title_fullStr | Fast And Accurate Receiver Jitter Tolerance Extrapolation Using The Q-Factor Linear Fitting Method |
| title_full_unstemmed | Fast And Accurate Receiver Jitter Tolerance Extrapolation Using The Q-Factor Linear Fitting Method |
| title_short | Fast And Accurate Receiver Jitter Tolerance Extrapolation Using The Q-Factor Linear Fitting Method |
| title_sort | fast and accurate receiver jitter tolerance extrapolation using the q-factor linear fitting method |
| topic | TK1-9971 Electrical engineering. Electronics. Nuclear engineering |
| url | http://eprints.usm.my/37335/ http://eprints.usm.my/37335/1/ABDUL_RAIS_BIN_ABDUL_RAHIM_24_Pages.pdf |