An experimental study for optimization of electrical discharge turning (EDT) process

QR Code

An experimental study for optimization of electrical discharge turning (EDT) process

The paper presents the application of the Taguchi robust design methods to optimize the precision and accuracy of the electrical discharge machining process (EDM) for machining of precise cylindrical forms on hard and difficult-to-machine materials. The present study has been carried out on the infl...

Full description

Bibliographic Details
Main Authors:	Matoorian, Pouria, Sulaiman, Shamsuddin, Megat Ahmad, Megat Mohamad Hamdan
Format:	Article
Language:	English English
Published:	2008
Online Access:	http://psasir.upm.edu.my/id/eprint/8277/ http://psasir.upm.edu.my/id/eprint/8277/1/An%20experimental%20study%20for%20optimization%20of%20electrical%20discharge%20turning.pdf

Similar Items

Turn bridge.
by: Salit, Mohd Sapuan, et al.
Published: (2009)

Experimental study of conventional wire electrical discharge machining for microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Experimental study of electrical discharge drilling of stainless steel UNS S30400
by: Hanash, Ebrahim, et al.
Published: (2018)

Intelligent approach for process modelling and optimization on electrical discharge machining of polycrystalline diamond
by: Pauline, Ong, et al.
Published: (2018)

Optimization Of A Cutting Process For Wire-Electric Discharge Machining At Welding Joint
by: F. R. M., Romlay, et al.
Published: (2007)

Experimental Investigation into Electrical Discharge Machining of Stainless Steel 304
by: M. M., Rahman, et al.
Published: (2011)

Machine Parameter Optimization For Wire-Electric Discharge Machining
by: F. R. M., Romlay, et al.
Published: (2008)

An experimental investigation on LM6 AL-SI alloy sand casting to study the correlation between metallurgical properties and solidification rate
by: Lim, Y. P., et al.
Published: (2005)

Optimization Of Material Removal Rate And Surface Roughness Using The Taguchi Method
by: Matoorian, Pooria
Published: (2008)

Optimization of cutting parameters on turning process based on surface roughness using response surface methodology
by: Yusuf, Muhammad, et al.
Published: (2012)

Dry electrical discharge machining: an environmental friendly machining process
by: Ali, Mohammad Yeakub
Published: (2018)

Effect of electrical discharge machining process parameter on surface topograhy
by: Lee, Wai Loon
Published: (2010)

Experimental investigation & optimisation of wire electrical discharge machining process parameters for Ni49Ti51 shape memory alloy
by: Goyal, Ashish, et al.
Published: (2021)

Heat transfer study in the low temperature thermal energy storage material (multi-component material) between tubes array during melting
by: Sulaiman, Suditama, et al.
Published: (2005)

Temperature distribution in copper electrode during electrical discharge machining process
by: Abdulkareem, Suleiman, et al.
Published: (2017)

Role of heat transfer on process characteristics during electrical discharge machining
by: Khan, Ahsan Ali
Published: (2011)

Influence of process parameters on electrical discharge machined job surface integrity
by: Iqbal, A.K.M. Asif, et al.
Published: (2010)

An experimental investigation of WC-Co tool life and tool wear in turning of titanium / Shamsiatun Shamsuddin
by: Shamsuddin, Shamsiatun
Published: (2016)

Optimization of turning parameters using ant colony optimization
by: Mohamad Nazri, Semoin
Published: (2008)

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Optimization of the electrical discharge machining performance on titanium alloy by using statistical method
by: Maizatul Asnida, Hassan
Published: (2013)

Effect of cutting parameters on tool-chip interface temperature in an orthogonal turning process
by: Sulaiman, Shamsuddin, et al.
Published: (2014)

Influence of cutting parameters on surface roughness for wet and dry turning process.
by: Mohd Ariffin, Mohd Khairol Anuar, et al.
Published: (2011)

An introduction to electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2011)

Wire electrical discharge machining for microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Implementation of Ant Colony Optimization Algorithm to Minimize Cost of Turning Process
by: M. F. F., Ab Rashid, et al.
Published: (2015)

Processing and characterisation of particulate reinforced aluminium silicon matrix composite
by: Hamouda, Abdel Magid Salem, et al.
Published: (2007)

Influence of Wire Electrical Discharge Machining (WEDM) process parameters on surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Investigation of process parameters for stable micro dry wire electrical discharge machining
by: Banu, Asfana, et al.
Published: (2019)

Optimization of electrical discharge machine parameter on mild steel by using response surface methodology
by: Mohd Amir Firdaus, Salleh
Published: (2010)

Surface Study in a Non-conventional (Electrical Discharge Machining) Process for Grade 6 Titanium Material
by: Md. Ashikur, Rahman Khan, et al.
Published: (2014)

Power Consumption Optimization in CNC Turning Process Using Multi Objective Genetic Algorithm
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2012)

The experimental study of partial discharge of Malaysian based palm oil
by: Aziz, Muhamad Fikri
Published: (2012)

Experimental characterization of filament wound glass/epoxy and carbon/epoxy composite materials
by: Hamed, Abdalla F., et al.
Published: (2008)

Influence of electrical discharge machining process parameters on surface micro-hardness of titanium alloy
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Parameters analysis in wire electrical discharge machine process of titanium alloys with dielectric alumina
by: Sapit, Azwan, et al.
Published: (2021)

Experimental investigation on aluminium composite surface machined by electrical discharge machining process using response surface methodology / R. Rajesh and M. Dev Anand
by: R. Rajesh, et al.
Published: (2013)

Wire Electrical Discharge Machining of Tungsten Carbide
by: Mas Ayu, Hassan
Published: (2008)

Electrical discharge machining (EDM): A review
by: Banu, Asfana, et al.
Published: (2016)

Surface formation and modification in electrical discharge machining
by: Ahmed, Shamraze
Published: (2022)