Measurement and analysis of thrust force and torque in friction drilling of difficult-to-machine materials

QR Code

Measurement and analysis of thrust force and torque in friction drilling of difficult-to-machine materials

Thrust force and torque applying in friction drilling contain some important information related to sufficient heat generation which can improve product quality and reduce tool wear. This concern becomes more challengeable when friction drilling is applied on difficult-to-machine materials. In the p...

Full description

Bibliographic Details
Main Authors:	Dehghan, Shayan, Ismail, Mohd Idris Shah, Ariffin, Mohd Khairol Anuar, Baharudin, B. T. Hang Tuah
Format:	Article
Language:	English
Published:	Springer 2019
Online Access:	http://psasir.upm.edu.my/id/eprint/81301/ http://psasir.upm.edu.my/id/eprint/81301/1/FRICTION.pdf

Similar Items

Friction drilling of difficult-to-machine materials: workpiece microstructural alterations and tool wear
by: Dehghan, Shayan, et al.
Published: (2019)

Friction drilling of difficult-to-machine materials: workpiece microstrutural alterations and tool wear
by: Dehghan, Shayan, et al.
Published: (2019)

Experimental and numerical investigation on friction drilling of difficult-to-machine materials
by: Dehghan, Shayan
Published: (2019)

Experimental investigation on friction drilling of titanium alloy
by: Dehghan, Shayan, et al.
Published: (2018)

Experimental Investigation on Friction Drilling of Stainless Steel AISI 304
by: Dehghan, Shayan, et al.
Published: (2019)

A novel approach to friction drilling process: experimental and numerical study on friction drill joining of dissimilar materials AISI304/AL6061
by: Dehghan, Shayan, et al.
Published: (2022)

Effect Of Twist Drill Geometry And Drilling Parameters On Thrust Force In Single-Shot Drilling Of Stack-Up Material
by: Chim, Yi Shen
Published: (2017)

Challenges in machining composite materials: impact of machining parameters on cutting force
by: Mohamad, Nurhaniza, et al.
Published: (2023)

Evaluation of thrust force in drilling of woven kenaf fiber reinforced epoxy composite laminates
by: Mokhtar, Suhaily, et al.
Published: (2017)

Evaluation of tool wear and machining performance by analyzing vibration signal in friction drilling
by: Abdul Mutalib, Mohd Zurrayen, et al.
Published: (2020)

Characterization of tool wear in friction drilling
by: Ismail, Mohd Idris Shah, et al.
Published: (2018)

Experimental investigation of forming forces in frictional stir incremental forming of aluminum alloy AA6061-T6
by: Baharudin, B. T. Hang Tuah, et al.
Published: (2017)

Thrust Force for Drone Propeller with Normal and Serrated Trailing Edge
by: Mohd Zaki Bahrom, Mohd Zaki Bahrom, et al.

Thrust Force for Drone Propeller with Normal and Serrated Trailing Edge
by: Bahrom, Mohd Zaki, et al.
Published: (2023)

Thrust Force for Drone Propeller with Normal and Serrated Trailing Edge
by: Bahrom, Mohd Zaki, et al.
Published: (2023)

Thrust Force for Drone Propeller with Normal and Serrated Trailing Edge
by: Bahrom, Mohd Zaki, et al.
Published: (2023)

Thrust Force for Drone Propeller with Normal and Serrated Trailing Edge
by: Bahrom, Mohd Zaki, et al.
Published: (2023)

Recent developments of kenaf fiber rein-forced thermoset composites: a review
by: Sreenivasan, S., et al.
Published: (2012)

Advanced machining towards improved machinability of difficult-to-cut materials
Published: (2011)

New torque and flux controllers for direct torque control of induction machines
by: Toh, C.L, et al.
Published: (2003)

Constant frequency torque and flux controllers for direct torque control of induction machines
by: Nik Idris, Nik Rumzi, et al.
Published: (2003)

Modeling Of A New Torque Controller For Direct Torque Control Of Induction Machines
by: Idris, Nik Rumzi, et al.
Published: (2000)

A reduced torque ripple controller for direct torque control of induction machines
by: Nik Idris, Nik Rumzi, et al.
Published: (2002)

Effect of chip load and spindle speed on cutting force of Hastelloy X
by: Mohd Nor, Nor Aznan, et al.
Published: (2020)

A new torque and flux controller for direct torque control of induction machines
by: Nik Idris, Nik Rumzi, et al.
Published: (2006)

A new torque and flux controllers for direct torque control of induction machines
by: Nik Idris, Nik Rumzi, et al.
Published: (2005)

Constant frequency torque and flux controllers for direct torque control of induction machines
by: Idris, N. R. N., et al.
Published: (2003)

An improved direct torque control of induction machines
by: Idris, N.R.N, et al.
Published: (2001)

Difficult in Dubai
by: Singh, Ajitpal
Published: (2012)

Multi-objective optimization in friction drilling of AISI1045 steel using grey relational analysis
by: Abdul Mutalib, Mohd Zurrayen, et al.
Published: (2020)

Determining optimum electro discharge machining parameters for drilling of a small hole by utilizing Taguchi method
by: Mohd Ariffin, Mohd Khairol Anuar, et al.
Published: (2014)

A review of using the force/torque sensor in robotics application
by: Mohd Zaini, Muhammad Zharif, et al.
Published: (2020)

CFD analysis of effect of flow and geometry parameters on thrust force created by flow from nozzle
by: Pathan, Khizer Ahmed, et al.
Published: (2017)

The difficult rheumatology diagnosis
by: Devaraj, Navin Kumar
Published: (2018)

High Thrust Density Transverse Flux Linear Motor: Thrust Analysis and Driving Method.
by: Misron, Norhisam, et al.
Published: (2011)

Clavicular osteotomy approach for difficult shoulder surgery
by: Khalid, Kamarul Ariffin, et al.
Published: (2008)

Performance study of organic based minimum quantity lubrication on machining difficult-to-cut material
by: Jamaludin, Ahmad Shahir, et al.
Published: (2019)

Development of force and temperature controlled friction stir welding machine (FSW) for dissimilar metal joining application
by: Ishak, M.
Published: (2018)

Development Of Multi-Component Loads, Torque And Temperature Measurement Device For Friction Stir Welding Process
by: Khairuddin, Jauhari Tahir.
Published: (2013)

Control of automatic drilling machine by PLC
by: Rahman , Md Mozasser, et al.
Published: (2011)