Important criteria for preparation of 3D printer filaments from polymer biocomposites

QR Code

Important criteria for preparation of 3D printer filaments from polymer biocomposites

Nowadays, there are many types of 3D printer filaments have been produced to fulfill the demand of small-scale fabrication industry. The use of polymer biocomposites as 3D printer filaments is one of the ways to reduce the depend-ence on the synthetic thermoplastics that are expensive and non-biodeg...

Full description

Bibliographic Details
Main Author:	Shamsuri, Ahmad Adlie
Format:	Article
Language:	English
Published:	ScienceVolks 2019
Online Access:	http://psasir.upm.edu.my/id/eprint/76428/ http://psasir.upm.edu.my/id/eprint/76428/1/76428.pdf

Similar Items

The Impact of organic salts on the tensile properties of polymer biocomposites
by: Shamsuri, Ahmad Adlie, et al.
Published: (2021)

The influence of ionic liquid pretreatment on the physicomechanical properties of polymer biocomposites: a mini-review
by: Shamsuri, Ahmad Adlie, et al.
Published: (2022)

Development of low cost 3D printer
by: Nor Azirah, Arifin
Published: (2017)

Patient-specific 3D printed models of renal tumours using home-made 3D printer in comparison with commerical 3D printer
by: Liu, D., et al.
Published: (2018)

Nanodiamonds in polymer hybrid composites
by: Shamsuri, Ahmad Adlie
Published: (2024)

An overview of fused filament fabrication technology and the advancement in PLA-biocomposites
by: Samykano, Mahendran, et al.
Published: (2024)

Development Of A Portable 3D Printer For Medical Modelling
by: Sin, Chia Ling
Published: (2020)

Mechanical properties of hybridized kenaf/chitosan fibres reinforced polyethylene biocomposites
by: Shamsuri, Ahmad Adlie, et al.
Published: (2017)

Is the polymer orientation can influence the mechanical properties of thermoplastic composites?
by: Shamsuri, Ahmad Adlie
Published: (2019)

Compatibilization potential of ionic liquid-based surfactants for polymer blends
by: Shamsuri, Ahmad Adlie
Published: (2018)

A review of natural fiber-based filaments for 3D Printing: filament fabrication and characterization
by: Ahmad, Mohd Nazri, et al.
Published: (2023)

Utilization of ionic liquids as compatibilizing agents for polymer blends-preparations and properties
by: Shamsuri, Ahmad Adlie, et al.
Published: (2023)

Preparations and properties of ionic liquid-assisted electrospun biodegradable polymer fibers
by: Shamsuri, Ahmad Adlie, et al.
Published: (2022)

Slicer method comparison using open-source 3D printer
by: Mohd Ariffin, M K A, et al.
Published: (2018)

Development of stack component for thermoacoustic refrigerator using 3d printer
by: Nor Atiqah, Zolpakar, et al.
Published: (2021)

Development Of A Small Scale Corexy Type 3D Printer
by: Yeoh, Xing Yuan
Published: (2021)

An initial investigation on microwaves reflection and transmission coefficients of oil palm empty fruit bunch biocomposites incorporated with nickel zinc ferrite
by: Shamsuri, Ahmad Adlie, et al.
Published: (2020)

Hardware improvement of FDM 3D printer: issue of bed leveling failures
by: Arief, Rudi Kurniawan, et al.
Published: (2019)

Development of two-fingered underactuated robot gripper using 3D printer
by: Sadun, Amirul Syafiq, et al.
Published: (2019)

Control Of 3d Printer Using Drone With Autopilot And Raspberry Pi Microcontroller
by: Sam, Jun Kok
Published: (2019)

Analysis and design of control system for desktop size concrete 3D printer
by: Iqbal, A. R., et al.
Published: (2022)

Development of Alumina Based Feedstock For Fused Deposition Modelling 3D Printer
by: Tan, Roe Djer
Published: (2020)

Design and develop an active mixer extruder for ink based 3D printer
by: Cheah, Choon Kit
Published: (2022)

The effect of imidazolium-based ionic liquids on the tensile properties of gellan gum/KCF biocomposite films - a prelude study
by: Shamsuri, Ahmad Adlie, et al.
Published: (2021)

Investigation of the Effect of nozzle temperature in fused deposition modelling on the mechanical properties and degradation behaviour of 3d-printed PLA/PCL/HA biocomposite filaments
by: Rifky, Ismail, et al.
Published: (2025)

The Effect of Printing Parameters on Scaffold Structure Using Low-cost 3D Printer
by: Sukindar, Nor Aiman, et al.
Published: (2020)

Utilizing rapid prototyping 3D printer for fabricating flexographic PDMS printing plate
by: Maksud, M. I., et al.
Published: (2016)

Thermal parameter affects on the part built using 3D printer Projet SD 3000
by: Ahmad, M. Syahrir, et al.
Published: (2012)

Nava - Printers in Milan
by: Simionato, Andy, et al.
Published: (2013)

Analysis on temperature setting for extruding polylactic acid using open-source 3D printer
by: Sukindar, Nor Aiman, et al.
Published: (2017)

Analysis of mechanical properties of polylactic acid using a new 3D printer nozzle
by: Sukindar, Nor Aiman, et al.
Published: (2018)

Analysis of mechanical properties of polylactic acid using a new 3D printer nozzle
by: Mohd Ariffin, Mohd Khairol Anuar, et al.
Published: (2018)

Continuous data collection of under extrusion in FDM 3D printers for deep-learning dataset
by: Liwauddin, Muhammad Lut, et al.
Published: (2022)

Materials behaviour analysis of 3D printed brass-PLA filament
by: Rajan, Dinesh Hasan, et al.
Published: (2024)

Development Of Soft And Flexible Filament For 3D Printing Of Anatomical Model
by: Ismail, Iman Firdaus
Published: (2022)

A prelude study on influence of hydrophobic ionic liquid on tensile and impact properties of HDPE/KCF biocomposites
by: Shamsuri, Ahmad Adlie, et al.
Published: (2021)

Effect of [C2mim][OTf] ionic liquid on tensile properties of HDPE/KCF biocomposites: a primary research
by: Shamsuri, Ahmad Adlie, et al.
Published: (2020)

Application of quaternary ammonium compounds as compatibilizers for polymer blends and polymer composites—a concise review
by: Shamsuri, Ahmad Adlie, et al.
Published: (2021)

Mechanical and thermal properties of Nylon-6/LNR/MMT nanocomposites prepared through emulsion dispersion technique
by: Shamsuri, Ahmad Adlie, et al.
Published: (2020)

Analysis on the impact process parameters on tensile strength using 3d printer repetier-host software
by: Sukindar, Nor Aiman, et al.
Published: (2017)