Optimization Of Material Removal Rate And Surface Roughness Using The Taguchi Method

QR Code

Optimization Of Material Removal Rate And Surface Roughness Using The Taguchi Method

A non-conventional hybrid machining method called electrical discharge turning (EDT) process is optimized in this research. The EDT process is a suitable method to produce small components with cylindrical geometries. This process is a type of hybrid electrical discharge machining (EDM), hence the m...

Full description

Bibliographic Details
Main Author:	Matoorian, Pooria
Format:	Thesis
Language:	English
Published:	2008
Subjects:	Electric discharges Taguchi methods (Quality control)
Online Access:	http://psasir.upm.edu.my/id/eprint/5349/ http://psasir.upm.edu.my/id/eprint/5349/1/FK_2008_7%20IR.pdf

Similar Items

Optimization of Lipase Catalysed Synthesis of Sugar Alcohol Esters Using Taguchi Method and Neural Network Analysis
by: Adnani, Seyedeh Atena
Published: (2011)

Application of Taguchi method in the optimization of biodiesel production from waste cooking oil using MoO3/SiO2 catalysts
by: Anwar, Nur Sharina
Published: (2012)

Dimensional Accuracy Achievable in Wire-cut Electrical Discharge Machining
by: Islam, Mohammad Nazrul, et al.
Published: (2011)

Characterization and optimization of electrospun TiO2/PVP nanofibers using Taguchi design of experiment method
by: Albetran, Hani Manssor Mohammed, et al.
Published: (2015)

Alignment parameter calibration for IMU using the Taguchi method for image deblurring
by: Chan, Kit Yan, et al.
Published: (2015)

Comparison of Dry and Flood Turning in Terms of Dimensional Accuracy and Surface Finish of Turned Parts
by: Rafai, Noor, et al.
Published: (2011)

Improving mechanical properties of recycled polypropylene-based composites using TAGuchi and ANOVA techniques
by: Zheng, Yitao, et al.
Published: (2017)

On-road sensor configuration design for traffic flow prediction using fuzzy neural networks and Taguchi method
by: Chan, Kit Yan, et al.
Published: (2013)

Selection of Significant On-Road Sensor Data for Short-Term Traffic Flow Forecasting Using the Taguchi Method
by: Chan, Kit, et al.
Published: (2012)

Effect of tool geometry on dimensional accuracy and surface finish of turned parts
by: Islam, Mohammad Nazrul, et al.
Published: (2013)

Sustainable Machining of Aerospace Material
by: Boswell, Brian, et al.
Published: (2013)

An Investigation of Surface Finish in Dry Turning
by: Islam, Mohammad Nazrul, et al.
Published: (2011)

Effect of Amount of Cutting Fluid on Surface Finish of Turned Parts
by: Islam, Mohammad Nazrul
Published: (2011)

Effect of cooling methods on dimensional accuracy and surface finish of a turned titanium part
by: Islam, Mohammad Nazrul, et al.
Published: (2013)

Application of Taguchi methods in the optimization of cutting parameters for surface roughness in turning
by: Mohamad Naim, Yusoff
Published: (2008)

Improved Multivariate Control Charts with Robust Methods
by: Shabbak, Ashkan
Published: (2011)

Optimization of Fly Ash Geopolymer Concrete Mixtures in a Seawater Environment
by: Olivia, Monita, et al.
Published: (2009)

Effect of Cutting Fluid Supply Strategies on Surface Finish of Turned Parts
by: Islam, Mohammad Nazrul, et al.
Published: (2011)

Micro wire electro discharge grinding: optimization of material removal rate and surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Surface roughness optimization of face milling operation using Taguchi design method
by: Mohd Azmi, Md Juni
Published: (2008)

Optimization of precision grinding parameters of silicon for surface roughness based on taguchi method
by: Abdur-Rasheed, Alao, et al.
Published: (2011)

Modelling of single spark interactions during electrical discharge coating
by: Algodi, Samer J., et al.
Published: (2018)

Introduction of Discharge Plan to Reduce Adverse Events Within 72 hours of discharge from the ICU
by: Williams, Teresa, et al.
Published: (2009)

Coupled electro-thermal transmission line modelling (TLM) method
by: Elkalsh, Ahmed
Published: (2017)

Effect of Additional Factors on Dimensional Accuracy and Surface Finish of Turned Parts
by: Islam, Mohammad Nazrul
Published: (2013)

Limits, stability and disturbance rejection analysis of voltage control loop strategies for grid forming converters in DC and AC microgrids with high penetration of constant power loads
by: Navarro-Rodríguez, Ángel, et al.
Published: (2017)

Electro-discharge machining of alumina: investigation of material removal rate and surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Process Improvement Through Six Sigma Methodology - Mv Machine Defective Reduction
by: Muid, Zalizan
Published: (2000)

Optimum Parameters for Machining Metal Matrix Composite
by: Boswell, Brian, et al.
Published: (2014)

Surface formation and modification in electrical discharge machining
by: Ahmed, Shamraze
Published: (2022)

Surface roughness and roundness optimization on turning process of Aluminium Alloy with Taguchi Method / Sudjatmiko … [et al.]
by: Sudjatmiko, djatmiko. mlg@gmail. com, et al.
Published: (2017)

Analysis of WEDM process parameters on surface roughness and kerf using Taguchi method
by: Banu, Asfana, et al.
Published: (2017)

Taguchi method approach on effect of lubrication condition on surface roughness in milling operation
by: Mohamad Syahmi, Shahrom
Published: (2012)

Effect of masked abrasive waterjet texturing on surface roughness using Taguchi method
by: Hafiz, Husin, et al.
Published: (2022)

Modelling of material removal rate in EDM of nonconductive ZrO2 ceramic by Taguchi method
by: Sabur, Abdus, et al.
Published: (2013)

Assessing the impact of the introduction of an electronic hospital discharge system on the completeness and timeliness of discharge communication: a before and after study
by: Mehta, Rajnikant, et al.
Published: (2017)

Analysis and optimum machining parameters on surface roughness and material removal rate for titanium alloy in milling machining with MQL
by: Siti Haryani, Tomadi, et al.
Published: (2023)

Surface roughness optimization using Taguchi method of high speed end milling for hardened steel D2
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2017)

Optimization of the surface roughness for titanium Ti6A14V in turning process using Taguchi method
by: Samin, R., et al.
Published: (2020)

Characterisation, modelling and tribological investigations of nano-structured TiC-based electrical discharge coatings
by: Algodi, Samer Jasim Mahmood
Published: (2018)