Effect of Loading Rate on Fracture Toughness Measurement of 7010 Aluminium Alloy and Mild Steel

QR Code

Effect of Loading Rate on Fracture Toughness Measurement of 7010 Aluminium Alloy and Mild Steel

The fracture toughness of structural material is a matter of vital interest in residual life and safety assessment work. Many structures in service today were erected in a time when safety requirements in terms of notch or fracture toughness were not specified. This means that often very little is k...

Full description

Bibliographic Details
Main Author:	Talib, Jamilah
Format:	Thesis
Language:	English English
Published:	2004
Online Access:	http://psasir.upm.edu.my/id/eprint/499/ http://psasir.upm.edu.my/id/eprint/499/2/549733_FK_2004_75.pdf

Similar Items

Effect of specimen size on fracture toughness of mild steel
by: Mohd Syafiq, Mohd Saufi
Published: (2012)

Modeling dynamic anisotropic behaviour and spall failure in commercial aluminium alloys AA7010
by: Mohd Nor, M. K., et al.
Published: (2018)

Effect of loading rates on fracture toughness of HDPE / Hassnol Ishraff Mohd Yusof
by: Mohd Yusof, Hassnol Ishraff
Published: (2002)

Performance of uncoated cutting tools when machining mild steel and aluminium alloy
by: Mohd Fahmi, Md Yusuf
Published: (2010)

Effect of strain rates on tensile properties and fracture toughness determination of extruded Mg-Al-Zn alloys
by: Abdul Latif, Noradila
Published: (2015)

Effect of microstructure on plain strain fracture toughness of carbon steel
by: Muhamad Hanif, Muhamad
Published: (2012)

Performance of coated carbide cutting tool while machining aluminium alloy and mild steel
by: Ismail, Ab.llah
Published: (2010)

Comparison studies of machinability for aluminium, mild steel and heat treated mild steel
by: Faiz Asyraf, Roslan
Published: (2008)

Effect of loading rates to the fracture toughness on carbon manganese steel ASTM 516 grade 70 / Abdullah Abd. Ghani and Mohd Fadhir Abd. Rahman
by: Abd. Ghani, Abdullah, et al.
Published: (1996)

Effect of loading rates on the fracture toughness of fiber metal laminate kenaf short fiber/epoxy/polyester / Eldridge George
by: George, Eldridge
Published: (2009)

Effects of absorbed hydrogen on fracture toughness of welded SA516 grade 70 steel
by: Maslan, Mohamad Haidir
Published: (2007)

Toughness investigation on ferrous-nonferrous weld metal joint (galvanized iron-aluminium alloy)
by: Muhammad Fakhrul, Hashim
Published: (2013)

Influence of varying depth of cut and feed rate to tool wear rate and surface roughness in aluminium, mild steel and P20 tool steel
by: Nadirah, Ismail
Published: (2012)

Development of microstructure and fracture toughness of AL-6063 alloy using equal channel angular extrusion
by: Nemati, Jamshid, et al.
Published: (2014)

Effect of anisotropy on fracture toughness of sandstone by SCB specimen
by: Funatsu, T., et al.
Published: (2012)

Effect of paper or silver nanowires-loaded paper interleaves on the electrical conductivity and interlaminar fracture toughness of composites
by: Guo, Miaocai, et al.
Published: (2018)

Effect of aluminium oxide and silicon carbide abrasive type on mild steel surface temperature
by: Mohd Hizam, Mohd Noor
Published: (2010)

Effect of silicon on strength and fracture surfaces of aluminium–silicon casting and heat treated alloys
by: Haque, Md. Mohafizul, et al.
Published: (2006)

Mechanical and fracture toughness behavior of TPNR nanocomposites
by: Ahmad, S. H., et al.
Published: (2007)

Synthesis of high fracture toughness of hydroxyapatite bioceramics
by: Tan, Chou Yong, et al.
Published: (2011)

Investigation of piezoelectric actuation effect on fracture toughness of isotropic materials
by: Hrairi, Meftah
Published: (2019)

Identification of kinematic hardening parameters for mild steel by cyclic loading
by: Muhammad Zakiran, Abd Aziz
Published: (2013)

Fracture toughness testing of geomaterials using semicircular specimen
by: Kuruppu, Mahinda
Published: (2018)

Fracture toughness of materials subjected to a temperature gradient
by: Shah, Qasim Hussain, et al.
Published: (1994)

The Influence of Fibre Aspect Ratio on the Fracture Toughness of SFRC
by: Noor Nabilah, Sarbini, et al.
Published: (2015)

Fracture toughness of kenaf mat reinforced polyester composite
by: Radif, Zainab Shakir, et al.
Published: (2011)

Fracture toughness of kenaf mat reinforced polyester matrix
by: Radif, Zainab Shaker, et al.
Published: (2009)

Effect of notching face on fracture toughness of green metal powder compacts
by: Alabi, A. A., et al.
Published: (2016)

High temperature fracture toughness and fatigue behavior of ti-zr-mo and w-re alloys for x-ray tube application
by: Harimon, Mohd Azhar
Published: (2017)

Dependence of the fracture toughness on the sintering time of dense hydroxyapatite bioceramics
by: Tolouei, Ranna, et al.
Published: (2011)

Mode 1 Fracture Toughness Of Natural Fibre Reinforced Composites
by: Nazri, Syaiful Nizam
Published: (2019)

Miniature Specimen Fracture Toughness Testing: A Concise Review
by: Azhar, Muhammad Asyraf
Published: (2022)

The influence of adiabatic heat and combined blast load and fire loading on the response of mild steel plates
by: Nurul Syafiqah, Abdul Razak, et al.
Published: (2023)

Strain-Rate Sensitivity of Boron Alloyed Steel
by: Salwani, Mohd Salleh, et al.
Published: (2015)

The effects of environmental factors on the corrosion rate of TGIC-free polyester coated mild steel
by: Choo, Ling Qian
Published: (2010)

Effect of Dimple Size onto Wear Rate of Mild Steel AISI 1060 Surface
by: Mohd Rahimi, Ramli, et al.
Published: (2021)

Effect of cylic stress range on crack growth of aluminium alloy under axial loading
by: Mohamad Shaffawi, Zainon
Published: (2010)

Study on drawing die radius to load and thinning pattern of aluminium alloy
by: Jamil, Nurul Izzati Mohamad
Published: (2019)

Improvement of adhesive toughness measurement
by: Meng, Qingshi, et al.
Published: (2011)

Wear characteristic of several commercial wrought aluminium alloys against tool steel
by: Mariyam Jameelah Ghazali,
Published: (2006)