Impact behaviour of composite plate with embedded piezoelectric sensor

QR Code

Impact behaviour of composite plate with embedded piezoelectric sensor

In engineering sciences, control and maintenance of the composite structures against environmental impacts is very important. Sensors are used for identifying impact location on the composite structures. Piezoelectric sensors are applied in two forms; bonded (on the composite) and embedded (in the c...

Full description

Bibliographic Details
Main Author:	Dezfouli, Mohammad Mehdi Salehi
Format:	Thesis
Language:	English
Published:	2011
Subjects:	Composite materials - Bonding Piezoelectric polymer biosensors
Online Access:	http://psasir.upm.edu.my/id/eprint/41777/ http://psasir.upm.edu.my/id/eprint/41777/1/FK%202011%204R.pdf

Similar Items

Design and simulation of piezoelectric micropump for a constant flow rate
by: A., Syed Abdul Bari
Published: (2016)

Behaviour of Composite I-Beams Under Crushing and Bending Modes
by: Ali, Farag Abdusslam
Published: (2004)

Structural and fluidic investigation of piezoelectric synthetic jet actuators for performance enhancements
by: Gungordu, Baris
Published: (2022)

Detection of delamination between steel bars and concrete using embedded piezoelectric actuators/sensors
by: Zhu, X., et al.
Published: (2013)

Harvesting energy from planetary gear using piezoelectric material
by: Hussein, Chilabi Haider Jaafar
Published: (2019)

Bond between textile reinforced mortar (TRM) and concrete substrate
by: Raoof, Saad Mahmood
Published: (2017)

Development of material selection expert system for polymer-based composite materials
by: Abd Manab, Mohd Fairuz
Published: (2011)

Flame retardancy study of recycled polymeric foam filled composite building material / Syed Anas Syed Mustafa, Rahmah Mohamed and Lily Soraya Amerudin
by: Syed Mustafa, Syed Anas, et al.
Published: (2015)

Mathematical dynamics of electromechanical piezoelectric energy harvesters
by: Lumentut, Mikail F.
Published: (2011)

Numerical analysis of frequency and electrical response in piezoelectric-covered components for energy harvesting
by: Lori, Erfan Shamsaddini
Published: (2020)

Dynamic modulus thermal analysis on polymer composite (high density polyethylene with natural rubber) / Sharadina Embong
by: Embong, Sharadina
Published: (2007)

The dielectric constant (ɛ') and loss tangent (δ) of magnetite (fe3o4) filled thermoplastic natural rubber composite / Farahanis Marudin
by: Marudin, Farahanis
Published: (2017)

Sintered-silver bonding of high-temperature piezoelectric ceramic sensors
by: Billore, Justine, et al.
Published: (2017)

Experimental and theoretical investigations of the impact localization of a passive smart composite plate fabricated using piezoelectric materials
by: Dezfouli, Mohammad Mehdi Salehi, et al.
Published: (2013)

Modelling analysis and optimisation of cantilever piezoelectric energy harvesters
by: Patel, Rupesh
Published: (2013)

Gelatin (binder) characterization of jackfruit seed starch for biodegradable plastic fabrication / Nur Hanisah Mohamad
by: Mohamad, Nur Hanisah
Published: (2017)

Fabrication and characterizations of additively manufactured PVDF-HFP composites for potential force sensing applications
by: Metwalli, Khaled Mohamed
Published: (2024)

A geometric parameter study of piezoelectric coverage on a rectangular cantilever energy harvester
by: Patel, R., et al.
Published: (2011)

Development of a dynamic model for piezoelectric raindrop energy harvesting
by: Wong, Voon-Kean
Published: (2018)

Effect of layer stacking sequence on residual compressive strength for hybrid composite plates
by: Randjbaran, Elias
Published: (2013)

Fabrication and characterization of jackfruit seed powder and polyvinyl alcohol blend as biodegradable plastic / Muhamad Faizal Haron
by: Haron, Muhamad Faizal
Published: (2017)

Analytical and Experimental Comparisons of Electromechanical Vibration Response of a Piezoelectric Bimorph Beam for Power Harvesting
by: Lumentut, Mikail, et al.
Published: (2013)

Development and characterization of flax/carbon/Kevlar reinforced bio-phenolic/epoxy blends hybrid composites for ballistic helmet
by: Ismail, Ahmad Safwan
Published: (2023)

Tow placement studies for liquid composite moulding
by: Turner, Matthew Richard
Published: (1998)

Low energy impact on the short kenaf fibre reinforced epoxy composites: effect to the residual strength and modulus / Syarifah Yunus … [et al.]
by: Yunus, Syarifah, et al.
Published: (2015)

Development of low cost, lossy and low dielectric constant OPEFB-HDPE composite material for microwave application
by: Balami, Sunday Dauda
Published: (2017)

Flexural strengthening of reinforced concrete beams using precast SIFCON thin plate
by: Abdul Aziz, Farah Nora Aznieta, et al.
Published: (2008)

Optimization of piezoelectric cantilever energy harvesters including non-linear effects
by: Patel, R., et al.
Published: (2014)

The Experimental Validation of an Electromechanical Dynamic Model of a Piezoelectric Bimorph Beam for Prediction of Power Generation
by: Lumentut, Mikail, et al.
Published: (2010)

Preparation And Characterization Of Calcium Copper Titanate Filled Epoxy Composites For Embedded Capacitor Applications
by: Dandan Satia, Mohd saidina
Published: (2015)

Impact performance and fracture toughness of PMC and PMC/FRP composite / Mohammad Helmi Jusoh @ Ibrahim
by: Jusoh @ Ibrahim, Mohammad Helmi
Published: (2004)

Preparation and characterization of Poly-3-hydroxybutrate/Poly(butylene-adipate-terephthalate) stearate-modified Zn3AI-layered double hydroxide nanocomposites
by: Pak , Yen Leng
Published: (2014)

Experimental modal analysis of composite plates with low velocity impact damage
by: Ling, Ellyna Chok Yee
Published: (2018)

Development of fibre optic bio-/chemical sensors for healthcare applications
by: Liu, LiangLiang
Published: (2019)

Full–scale validation and implementation guidelines of combined piezoelectric sensing and big data analytics for long-term pavement performance monitoring
by: Manosalvas-Paredes, Mario
Published: (2021)

Controllable synthesis of transition metal nitride materials and performance tuning in photocatalysis and piezoelectric catalysis
by: Cheng, Zhixing
Published: (2021)

Crushing behaviour of kenaf fibre-reinforced epoxy composite elliptical tubes
by: M Alkateb, Mohamed Mohamed
Published: (2018)

Development of PNA electrochemical biosensor based on screen-printed electrode-modified amine-functionalized graphene composite for Mycobacterium tuberculosis detection
by: Mat Zaid, Mohd Hazani
Published: (2017)

UNIVERSITI SAINS MALAYSIA Second Semester Examination 2012/2013 Academic Session June 2013 EBP 317/3- Advanced Polymer Composites [Komposit Polimer Termaju] Duration : 3 hours [Masa : 3 jam]
by: Bahan & Sumber Mineral, Pusat Pengajian Kejuruteraan
Published: (2013)

Low velocity impact analysis of pineapple leaf/kenaf fibre-reinforced vinyl ester hybrid composites for structural applications
by: Mazlan, Ali Ahmad
Published: (2021)