Development of a testing facility for modelling cooling technique

QR Code

Development of a testing facility for modelling cooling technique

Development of a low speed testing facility, adopting blow tunnel configurations and specialised working section arrangements for general purposes flow and heat transfer investigations, is described. This article reports a preliminary design of the testing facility within the constraint of fabricati...

Full description

Bibliographic Details
Main Authors:	Jaafar, Abdul Aziz, Abu Talib, Abd Rahim, Abdul Rahim, I., Filipski, Mohammad Nizam, Salit, Mohd Sapuan
Format:	Conference or Workshop Item
Language:	English
Published:	Federation of Engineering Institutions of Islamic Countries 2006
Online Access:	http://psasir.upm.edu.my/id/eprint/39473/ http://psasir.upm.edu.my/id/eprint/39473/1/39473.pdf

Similar Items

Commissioning the UPM satellite simulator facility platform
by: Low, Yee Seng, et al.
Published: (2008)

Heat transfer performance of multiple holes impingement cooling technique
by: Mohd Zulkeple, Muhammad Fitri, et al.
Published: (2018)

Development of a Laboratory Model Retaining Wall Test Facility.
by: Chow , Shiao Huey, et al.
Published: (2008)

Effects of blowing ratio on the heat transfer coefficient distribution downstream of a single film cooling hole
by: Abu Talib, Abd Rahim, et al.
Published: (2006)

A new cooling technique for stingless bees hive
by: Luqman, Abdul Halim, et al.
Published: (2017)

Proposed research for optimization of the performance of cooling system in data center facilities
by: Romadhon, Rahmat, et al.
Published: (2008)

An examination of dynamic test facilities
by: Player, John, et al.
Published: (2008)

Development of diesel engines cooling system
by: Mohammad Naqib Amirul, Abdul Rashid
Published: (2012)

Development of fault detection and diagnosis for reactor cooling system by using artificial intelligent techniques
by: Abdul Rahman, R. Z., et al.
Published: (2023)

A clinical test for a newly developed direct brain cooling system for the injured brain and pattern of cortical brainwaves in cooling, non-cooling and dead brain
by: Yee, Ang Song
Published: (2020)

Satellite orbit estimation using earth magnetic field measurements
by: Filipski, Mohammad Nizam, et al.
Published: (2006)

Comparison on cooling efficiency of cooling pad materials for evaporative cooling system
by: Radhiyah, Abd Aziz, et al.
Published: (2018)

Development of an Experimental Facility for Measurement of Tangential Jet Flow in a Sudden Expansion Channel
by: Abd Rahim, Irfan
Published: (2006)

Comparison of Cooling Cost Effectiveness Between Unitary and Central Cooling System
by: Abd Aziz, Azizuddin
Published: (2005)

Development of TiO2 coated activated carbon foam as cooling pad for direct evaporative cooling system
by: Radhiyah, Abd Aziz, et al.
Published: (2018)

Numerical analysis of heat transfer in cooling of fish packages
by: Abbas, Kassim Ali, et al.
Published: (2006)

NOx emission reduction from gas burner system applying water cooling technique
by: Mohd. Jaafar, Mohammad Nazri, et al.
Published: (2000)

Evaluation of a spacecraft attitude and rate estimation algorithm
by: Abdullah, Mohammad Nizam Filipski, et al.
Published: (2010)

Cooling techniques for single photon avalanche diode
by: Samsuddin, Nurul Izzati, et al.
Published: (2011)

Recent progresses and challenges in cooling techniques of concentrated photovoltaic thermal system: A review with special treatment on phase change materials (PCMs) based cooling
by: Rosli, M. Arif Fikri, et al.
Published: (2022)

Development of a hovercraft prototype with an aluminium hull base
by: Abdul Kadir, Amirruddin, et al.
Published: (2011)

Performance characteristics monitoring of turboprop engine for the development of preliminary requirement of an engine testing facility
by: Mohd Yunos, Siti Nur Mariani
Published: (2011)

Design and development of an indoor testing facility for downwash and spray distribution evaluations of agricultural UAV
by: Ismail, Siti Amni, et al.
Published: (2020)

Temperature and heat flux measurement techniques for aeroengine fire test: a review
by: Mohammed, I., et al.
Published: (2016)

A preliminary study on new cooling techniques for stingless bees hive
by: Luqman, Abdul Halim, et al.
Published: (2020)

The study on the soil heat transfer characteristics for the development of a cost-saving underground air cooling system
by: Din, Abdul Talib, et al.
Published: (2011)

Cutting-edge cooling techniques for photovoltaic systems: A comprehensive review
by: Rajamony, Reji Kumar, et al.

Cutting-edge cooling techniques for photovoltaic systems: a comprehensive review
by: Rajamony, Reji Kumar, et al.
Published: (2025)

Numerical investigation of heat transfer enhancement via dimpled target surface configuration and jet arrangement in impingement cooling
by: Mohd Zulkeple, Muhammad Fitri, et al.
Published: (2024)

Comprehensive analysis of geometric hole designs and configurations in film cooling for gas turbine engines: a critical review
by: Abu Talib, Abd Rahim, et al.
Published: (2024)

Using the morphological chart technique for the design of polymeric-based composite automotive pedals
by: Salit, Mohd Sapuan
Published: (2006)

Potential of direct evaporative cooling system under metal plate attachment to wetted pad application
by: Mohd Syahray Izham, Muhazihat, et al.
Published: (2018)

Development of peltier cooling system for automotive
by: Mohamed, Amir Izzani, et al.
Published: (2017)

Development and Testing of a Modified Version of the Brief Pain Inventory for Use in Residential Aged Care Facilities
by: Auret, K., et al.
Published: (2008)

Cooling panel wall system with difference types of cooling mediums
by: Salleh, Norhafizah, et al.
Published: (2020)

Cooling panel wall system with difference types of cooling mediums
by: Salleh, Norhafizah, et al.
Published: (2020)

Environmental friendly cutting fluids and cooling techniques in machining: a review
by: Debnath, Sujan, et al.
Published: (2014)

Night Cooled Radiant Cooling Panel for Sustainable Building Cooling Mode in Malaysia
by: Baharun, Azhaili, et al.
Published: (2018)

Modelling of an interacting series process for rector cooling system using system identification method
by: Mohammad Abdul Aziz, Nur Aina, et al.
Published: (2022)

Comparing topical anaesthesia, local cooling and vibration technique as pain control during palatal local anaesthetic injection
by: Aziz, Nur Izzati, et al.
Published: (2019)