Effect of machining process on surface microhardness of titanium carbide reinforced aluminium LM6 composite

QR Code

Effect of machining process on surface microhardness of titanium carbide reinforced aluminium LM6 composite

Due to the fact that material is being removed from the bulk material, all machining operations have some impact on the resulting surface integrity of the machined components. This paper presents an investigation on surface microhardness on machining of TiC reinforced aluminium LM6 alloy composite u...

Full description

Bibliographic Details
Main Authors:	Yusuf, Muhammad, Mohd Ariffin, Mohd Khairol Anuar, Ismail, Napsiah, Sulaiman, Shamsuddin
Format:	Article
Language:	English
Published:	Trans Tech Publications 2014
Online Access:	http://psasir.upm.edu.my/id/eprint/37267/ http://psasir.upm.edu.my/id/eprint/37267/1/Effect%20of%20machining%20process%20on%20surface%20microhardness%20of%20titanium%20carbide%20reinforced%20aluminium%20LM6%20composite.pdf

Similar Items

Experimental investigation on surface roughness and tool wear in dry machining of TiC reinforced aluminium LM6 composite
by: Yusuf, Muhammad, et al.
Published: (2014)

Experimental investigation on surface roughness and tool wear in dry machining of TiC reinforced aluminium LM6 composite
by: Yusuf, Muhammad, et al.
Published: (2012)

Surface quality and chip formation in turning of LM6 aluminium alloy and particulate reinforced metal matrix composite
by: Yusuf, Muhammad, et al.
Published: (2014)

Surface quality and chip formation in turning of LM6 aluminium alloy and particulate reinforced metal matrix composite
by: Yusuf, Muhammad, et al.
Published: (2012)

Solidification analysis in permanent mould casting of aluminium alloy LM6 reinforced titanium carbide particulates metal matrix composites
by: Fatchurrohman, Nanang, et al.
Published: (2017)

Solidification analysis in permanent mould casting of aluminium alloy LM6 reinforced titanium carbide particulates metal matrix composites
by: Fatchurrohman, Nanang, et al.
Published: (2017)

Thermal investigation of aluminium - 11.8% silicon (LM6) reinforced SiO2 - particles
by: Mohd Sayuti,, et al.
Published: (2011)

Metal matrix composites: solidification parameters of aluminium-11.8% silicon alloy reinforced with titanium carbide particulates
by: Fatchurrohman, Nanang, et al.
Published: (2011)

Properties of titanium carbide reinforced aluminium silicon alloy matrix
by: M. Sayuti,
Published: (2012)

Cutting parameter optimisation for aluminium LM6 composite using experimental design
by: Yusuf, Muhammad
Published: (2013)

Influence of mechanical vibration moulding process on the tensile properties of TiC reinforced LM6 alloy composite castings
by: M. Sayuti, et al.
Published: (2011)

Mechanical properties of the as-cast quartz particulate reinforced LM6 alloy matrix composites
by: Sulaiman, Shamsuddin, et al.
Published: (2008)

Production and solidification analysis of titanium carbide particulates reinforced aluminium alloy matrix composite by vortex mixing - sand casting technique
by: Fatchurrohman, Nanang, et al.
Published: (2010)

The effect of vortex well thickness on microstructure and mechanical properties of aluminium LM6
by: Hehsan, Haffidzudin
Published: (2013)

Influence of pattern coating thickness on porosityand mechanical properties of lost foam casting of Al-Si (LM6) alloy
by: Sulaiman, Shamsuddin, et al.
Published: (2013)

Surface texturing potential on carbide insert in reducing aluminium alloy adhesiveness during machining
by: Chia, Yun Qi, et al.
Published: (2019)

Solidification analysis of metal matrix composites aluminium 11.8% silicon alloy reinforced with titanium carbide particulates
by: Fatchurrohman, Nanang
Published: (2009)

Effect of material modifier and vibration on mechanical and microstructure properties of aluminium LM6 composite casting
by: Alhajji, Mohammad Sh I A M I
Published: (2021)

Development of ceramic cutting insert of aluminium oxide (Al2O3) and titanium carbide (TiC) for machining steel
by: Isa, Mohd. Akmal
Published: (2007)

Microhardness and microstructure of aluminium alloy 5052 by high-pressure torsion process and subsequent annealing
by: Ahmad Muhammad Aziz,, et al.
Published: (2024)

The Effect of Particulate Reinforcement Addition to Latent Heat and Solid Fraction During Solidification of Titanium Carbide Particulates Reinforced Aluminium Alloy Matrix Composite Produced by Vortex Mixing-Sand Casting Technique
by: Fatchurrohman, Nanang, et al.
Published: (2010)

Mechanical Properties of The As-Cast Quartz Particulate Reinforced Lm6 Alloy Matrix Composites
by: M. Sayuti
Published: (2005)

Formation of nitrides and carbides on titanium alloy surface through EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2012)

Solidification Analysis of Aluminium 11.8% Silicon Alloy Reinforced With Titanium Carbide Particulates Produced Using Vortex Mixing - Permanent Mould Casting
by: Fatchurrohman, Nanang, et al.
Published: (2016)

Melting of multipass surface tracks in steel incorporating titanium carbide powders
by: Mridha, Shahjahan, et al.
Published: (2015)

Effect of Lead Addition in LM6 Alloy Castings
by: S.THIRU,, CHITRAMBALAM
Published: (2010)

Optimization of cutting parameters on turning process based on surface roughness using response surface methodology
by: Yusuf, Muhammad, et al.
Published: (2012)

Influence of heat treatment on microstructure, mechanical properties, and corrosion behaviour of LM6 reinforced with copper powder
by: Aljermi, Almukhtar IB. A.
Published: (2021)

Performance of coated and uncoated carbide tools while dry machining aluminium alloy
by: Amin Abidin, Buran
Published: (2010)

Wear characteristics of multiple particle size silicon carbide reinforced aluminium composite
by: Abdulmumin, Adebisi Adetayo, et al.
Published: (2015)

Effect of aluminium oxide and silicon carbide abrasive type on mild steel surface temperature
by: Mohd Hizam, Mohd Noor
Published: (2010)

Mechanical properties of particulate reinforced aluminium alloy matrix composite
by: Mohd Sayuti,, et al.
Published: (2010)

Processing and characterisation of particulate reinforced aluminium -11.8% silicon matrix composite
by: M., Sayuti, et al.
Published: (2010)

Development of surface roughness models in end milling titanium alloy Ti-6Al-4V using uncoated tungsten carbide inserts
by: Ginta, Turnad Lenggo, et al.
Published: (2009)

Effect of heat treatment parameters on the microstructure and microhardness of Ti-6Al-4V alloy
by: Abdalla, Ayad Omran, et al.
Published: (2016)

Performance of coated carbide cutting tool while machining aluminium alloy and mild steel
by: Ismail, Ab.llah
Published: (2010)

Developments in Machining of Stacked Materials Made of CFRP and Titanium/Aluminium Alloys
by: Pramanik, Alokesh, et al.
Published: (2014)

Influence of cutting parameters on surface roughness for wet and dry turning process.
by: Mohd Ariffin, Mohd Khairol Anuar, et al.
Published: (2011)

Surface roughness of Carbides produced by abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2005)

Surface roughness of carbides produced by water abrasive jet machining
by: Ali Khan, Ahsan, et al.
Published: (2011)