The analysis of coating performance on stainless steel in high speed machining
This paper describes the performance of coated tools inserts (TiAlN, Al2O3 and TiCN) when machining stainless steel AISI 416 at high cutting speed. The effects of cutting speed and feed rate on the surface roughness and tool life were studied experimentally. The settings of machining parameters were...
| Main Authors: | , , , , |
|---|---|
| Format: | Article |
| Language: | English |
| Published: |
American-Eurasian Network for Scientific Information
2014
|
| Online Access: | http://psasir.upm.edu.my/id/eprint/35625/ http://psasir.upm.edu.my/id/eprint/35625/1/The%20analysis%20of%20coating%20performance%20on%20stainless%20steel%20in%20high%20speed%20machining.pdf |
| _version_ | 1848848107239899136 |
|---|---|
| author | Ngah, Norsilawati Baharudin, B. T. Hang Tuah Shari, Na'ain Mohamad, Ahmad Joraimee Raja Mamat, Raja Manisa |
| author_facet | Ngah, Norsilawati Baharudin, B. T. Hang Tuah Shari, Na'ain Mohamad, Ahmad Joraimee Raja Mamat, Raja Manisa |
| author_sort | Ngah, Norsilawati |
| building | UPM Institutional Repository |
| collection | Online Access |
| description | This paper describes the performance of coated tools inserts (TiAlN, Al2O3 and TiCN) when machining stainless steel AISI 416 at high cutting speed. The effects of cutting speed and feed rate on the surface roughness and tool life were studied experimentally. The settings of machining parameters were determined by using general full factorial design method. For tested range of milling conditions, the result shows that the surface roughness is highly affected by the feed rate, while tool life is highly affected by combination of cutting speed and feed rate. TiAlN coating performs better followed by Al2O3 coating and TiCN coating. Slow wear rate were observed at the combination of cutting parameters which are low cutting speed (260m/min) and feed rate (0.24mm/rev). Meanwhile, interaction between low value of feed rate (0.24mm/rev) and high value of cutting speed (320m/min) that produce good surface finish. Generally, TiAlN coated tool perform better than another coated tools, in terms of surface finish and tool life with current parameters. |
| first_indexed | 2025-11-15T09:29:14Z |
| format | Article |
| id | upm-35625 |
| institution | Universiti Putra Malaysia |
| institution_category | Local University |
| language | English |
| last_indexed | 2025-11-15T09:29:14Z |
| publishDate | 2014 |
| publisher | American-Eurasian Network for Scientific Information |
| recordtype | eprints |
| repository_type | Digital Repository |
| spelling | upm-356252016-04-26T01:54:13Z http://psasir.upm.edu.my/id/eprint/35625/ The analysis of coating performance on stainless steel in high speed machining Ngah, Norsilawati Baharudin, B. T. Hang Tuah Shari, Na'ain Mohamad, Ahmad Joraimee Raja Mamat, Raja Manisa This paper describes the performance of coated tools inserts (TiAlN, Al2O3 and TiCN) when machining stainless steel AISI 416 at high cutting speed. The effects of cutting speed and feed rate on the surface roughness and tool life were studied experimentally. The settings of machining parameters were determined by using general full factorial design method. For tested range of milling conditions, the result shows that the surface roughness is highly affected by the feed rate, while tool life is highly affected by combination of cutting speed and feed rate. TiAlN coating performs better followed by Al2O3 coating and TiCN coating. Slow wear rate were observed at the combination of cutting parameters which are low cutting speed (260m/min) and feed rate (0.24mm/rev). Meanwhile, interaction between low value of feed rate (0.24mm/rev) and high value of cutting speed (320m/min) that produce good surface finish. Generally, TiAlN coated tool perform better than another coated tools, in terms of surface finish and tool life with current parameters. American-Eurasian Network for Scientific Information 2014 Article PeerReviewed application/pdf en http://psasir.upm.edu.my/id/eprint/35625/1/The%20analysis%20of%20coating%20performance%20on%20stainless%20steel%20in%20high%20speed%20machining.pdf Ngah, Norsilawati and Baharudin, B. T. Hang Tuah and Shari, Na'ain and Mohamad, Ahmad Joraimee and Raja Mamat, Raja Manisa (2014) The analysis of coating performance on stainless steel in high speed machining. Australian Journal of Basic and Applied Sciences, 8 (spec.4). pp. 528-531. ISSN 1991-8178 http://ajbasweb.com/old/2-ajbas_Special_2014.html |
| spellingShingle | Ngah, Norsilawati Baharudin, B. T. Hang Tuah Shari, Na'ain Mohamad, Ahmad Joraimee Raja Mamat, Raja Manisa The analysis of coating performance on stainless steel in high speed machining |
| title | The analysis of coating performance on stainless steel in high speed machining |
| title_full | The analysis of coating performance on stainless steel in high speed machining |
| title_fullStr | The analysis of coating performance on stainless steel in high speed machining |
| title_full_unstemmed | The analysis of coating performance on stainless steel in high speed machining |
| title_short | The analysis of coating performance on stainless steel in high speed machining |
| title_sort | analysis of coating performance on stainless steel in high speed machining |
| url | http://psasir.upm.edu.my/id/eprint/35625/ http://psasir.upm.edu.my/id/eprint/35625/ http://psasir.upm.edu.my/id/eprint/35625/1/The%20analysis%20of%20coating%20performance%20on%20stainless%20steel%20in%20high%20speed%20machining.pdf |