Temperature distribution of micro milling process due to uncut chip thickness

QR Code

Temperature distribution of micro milling process due to uncut chip thickness

A simplified model for micro milling process is presented, as well as results on temperature on tool and work piece. The purpose is to investigate on finite element modelling of two flute micro end milling process of titanium alloy, Ti6Al4V with prediction of temperature distribution. ABAQUS/Explici...

Full description

Bibliographic Details
Main Authors:	Baharudin, B.T Hang Tuah, Ng, Kooi Pin, Sulaiman, Shamsuddin, Samin, Razali, Ismail, Mohd Shahrom
Format:	Article
Language:	English
Published:	Trans Tech Publications 2014
Online Access:	http://psasir.upm.edu.my/id/eprint/35611/ http://psasir.upm.edu.my/id/eprint/35611/1/Temperature%20distribution%20of%20micro%20milling%20process%20due%20to%20uncut%20chip%20thickness.pdf

Similar Items

Investigation of chip formation and minimum chip thickness in micro/meso milling: Methodology and design of experiment
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Prediction of minimum chip thickness in tool based micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Effect of micro end milling tool diameter on minimum chip thickness
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Investigation of minimum chip thickness in micro end milling of PMMA: process development
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Micro/meso milling of aluminium alloy 1100: analysis and modelling of minimum chip thickness
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Investigation of minimum chip thickness in micro end milling of PMMA: Experiment and analysis 800 µm diameter tool
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Investigation of minimum chip thickness in micro end milling of PMMA: experiment and analysis 1.0 mm diameter tool
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Tool vibration due to high speed micro end milling parameters
by: Mohamed, Abd. Rahman, et al.
Published: (2013)

Chip pattern, burr and surface roughness in laser assisted micro milling of Ti6Al4V using micro ball end mill
by: Mohid, Z., et al.
Published: (2018)

Surface defects in groove milling of Hastelloy-C276 under fluid coolant
by: Al-Falahi, Muath, et al.
Published: (2016)

On-chip micro-spectrometer for fluorescence bio-sensing
by: Hu, Z., et al.
Published: (2011)

On-chip micro-spectrometer for fluorescence bio-sensing
by: Hu, Z., et al.
Published: (2011)

Thick-film Piezoceramic Micro-generators
by: Kok, Swee Leong, et al.
Published: (2008)

An evaluation of the characteristics of metal cutting fluid due to the metal chips contamination
by: Idrus, I.
Published: (2002)

Effect of chip load and spindle speed on cutting force of Hastelloy X
by: Mohd Nor, Nor Aznan, et al.
Published: (2020)

Fabrication of micro magnetometer using flip-chip bonding
by: Tengku Azmi, Tengku Muhammad Afif, et al.
Published: (2017)

Minimum chip thickness in machining MEMS structure using Tool Based Micromilling
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

The influence of mechanical mold vibration on temperature distribution and physical properties of Al-11.8%Si matrix composites
by: Sayuti, M., et al.
Published: (2012)

Incremental sheet forming (ISF) of AISI 316 stainless steel sheet using CNC milling machine
by: Moayedfar, Majid, et al.
Published: (2014)

Fabrication of micro magnetometer using flip-chip bonding technique
by: Tengku Azmi, Tengku Muhammad Afif, et al.
Published: (2017)

Effect of cutting parameters on tool-chip interface temperature in an orthogonal turning process
by: Sulaiman, Shamsuddin, et al.
Published: (2014)

Analysis on tool life and surface characteristic in milling Stavax Supreme material
by: Che Ibrahim, Muhd Fathil, et al.
Published: (2014)

Fabrication of microfluidic channel using micro end milling and micro electrical discharge milling
by: Ali, Mohammad Yeakub
Published: (2009)

Coating performance in high speed micro machining of H13 tool steel
by: Baharudin, B. T. Hang Tuah, et al.
Published: (2010)

Simulation and fabrication of micro magnetometer using flip-chip bonding technique
by: Tengku Azmi, Tengku Muhammad Afif, et al.
Published: (2017)

Simulation and fabrication of micro magnetometer using flip-chip bonding technique
by: Tengku Azmi, Tengku Muhammad Afif, et al.
Published: (2019)

Simulation and fabrication of micro magnetometer using flip-chip bonding technique
by: Tengku Azmi, Tengku Muhammad Afif, et al.
Published: (2019)

Magneto-optical traps on a chip using micro-fabricated gratings
by: Nshii, C., et al.
Published: (2013)

Review of Aluminum Chip Machining Using Direct Recycling Process
by: A. R., Yusoff, et al.
Published: (2014)

Performance of laser assisted micro-milling (laμmill) of titanium alloy using micro ball end mill
by: Mohid, Zazuli
Published: (2018)

Response surface methodology approach for chip serration Frequency Prediction in milling
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2008)

Mathematical model of chip serration frequency in end milling of Inconel 718
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2008)

On-chip hotplate for temperature control of CMOS SAW resonators
by: Nordin, Anis Nurashikin, et al.
Published: (2008)

Machining of injection mould materials for different cutting flute in low-speed end milling
by: Shari, Naain, et al.
Published: (2014)

Decreasing of grid-tied PV power output due to thick haze phenomena in Malaysia
by: Ya'acob, Mohammad Effendy, et al.
Published: (2014)

Micro Electro Discharge Milling for Microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Vibration issue in micro end milling
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Dynamic analysis of micro-milling machine
by: Hassan, S., et al.
Published: (2014)

Chip serration frequency-the primary cause of chatter during end milling operation
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2011)

Chip serration frequency-the primary cause of chatter during end milling operation
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2009)