Simulation of thermoset injection for bulk moulding compounds (BMC)

QR Code

Simulation of thermoset injection for bulk moulding compounds (BMC)

This paper discusses about the simulation of the process of injection moulding for thermoset materials namely Bulk Moulding Compounds (BMC). BMC is a polyester resin based compound with glass fibre additives. In this paper a complex part was used to simulate and obtain the parameters for moulding BM...

Full description

Bibliographic Details
Main Authors:	Mohd Ariffin, Mohd Khairol Anuar, Sulaiman, Shamsuddin, Baharudin, B. T. Hang Tuah, Tang, Sai Hong, Sreenivasan, Subramaniasarma
Format:	Article
Language:	English
Published:	Trans Tech Publications 2011
Online Access:	http://psasir.upm.edu.my/id/eprint/22915/ http://psasir.upm.edu.my/id/eprint/22915/1/22915.pdf

Similar Items

Recent developments of kenaf fibre reinforced thermoset composites: review
by: Sreenivasan, Subramaniasarma, et al.
Published: (2013)

Recent developments of kenaf fiber rein-forced thermoset composites: a review
by: Sreenivasan, S., et al.
Published: (2012)

Design, Analysis and Fabrication of Plastic Injection Mould for Tensile Test Specimen
by: Mohd Ariffin, Mohd Khairol Anuar
Published: (2001)

Evaluation of combined treatments of natural fibers: kenaf, abaca and oil palm fibers using micromechanical and SEM methods
by: Sreenivasan, Subramaniasarma, et al.
Published: (2014)

The use of Taguchi method in the design of plastic injection mould for reducing warpage
by: Tang, Sai Hong, et al.
Published: (2007)

Green compression strength of tin mine tailing sand for green sand casting mould
by: Abdullah, Azhar, et al.
Published: (2013)

Machining of injection mould materials for different cutting flute in low-speed end milling
by: Shari, Naain, et al.
Published: (2014)

The influence of mechanical vibration moulding process on thermal conductivity and diffusivity of Al-TiC particulate reinforced composites
by: Mohd Sayuti,, et al.
Published: (2011)

Mechanical moulding properties of tailing sand-clay mixture from Batu Gajah, Perak, Malaysia
by: Abdullah, Azhar, et al.
Published: (2012)

Mechanical properties of tin tailing sand-clay mixture from Batu Gajah, Perak, Malaysia for making greensand casting mould
by: Abdullah, Azhar, et al.
Published: (2014)

Fibre insert mould for injection moulding
by: Norjamalullail Tamri,, et al.
Published: (2020)

The effect of bentonite clay on green compression strength for tailing sands from old tin mines in Perak state, Malaysia for making green sand casting mould
by: Abdullah, Azhar, et al.
Published: (2011)

Influence of mechanical vibration moulding process on the tensile properties of TiC reinforced LM6 alloy composite castings
by: M. Sayuti, et al.
Published: (2011)

Optimization Of Injection Moulding Process For Hdpe Moulded Gear
by: Kassim, Mohd Syahir Mohd
Published: (2015)

Numerical simulation on moulded thin-walled parts via injection moulding process
by: Md Deros, Mohd Azaman, et al.
Published: (2014)

Properties of wood plastic composite produced using injection moulding process
by: Hang, Chit Meng
Published: (2010)

BASE: a bacteria foraging algorithm for cell formation with sequence data
by: Nouri, Hossein, et al.
Published: (2010)

Design and Simulation of Plastic Injection Moulding Process
by: Wong, Choon Tat, et al.
Published: (2004)

Improvement of Tops Spinning manufacturing with CNC Lathe
by: Sulaiman, Shamsuddin, et al.
Published: (2011)

Optimisation of Injection Moulding Process Parameters
by: Guna Rao, Kishyen Raao, et al.
Published: (2024)

Biogeography based optimization (BBO) algorithm to minimise non-productive time during hole-making process
by: Tamjidy, Mehran, et al.
Published: (2015)

Development and tuning of bacteria foraging optimization algorithm on cell formation in cellular manufacturing system
by: Nouri, Hossein, et al.
Published: (2013)

Metaheuristic techniques on cell formation in cellular manufacturing system
by: Nouri, Hossein, et al.
Published: (2013)

Injection moulding and thermal properties of polypropylene hinges
by: Othman, Mohd Hilmi
Published: (2008)

Process control in injection moulding machine
by: Hashim, Shahrir
Published: (1993)

Biological durability of injection moulded wood plastic composite boards
by: H'ng, Paik San, et al.
Published: (2011)

Improvement of tops spinning manufacturing with CNC lathe
by: Sulaiman, Shamsuddin, et al.
Published: (2011)

A Study on Injection Moulding and Injection Blow Molding Technology
by: Sokkalingam, Rajalingam
Published: (2009)

Performance of assessment model for Injection moulding parameters
by: Nur Qurratul Ain, Adanan, et al.
Published: (2022)

Compounding, injection moulding and characterisation of mangrove particle/high density polyethylene Composites / Ganiyat Olusola Adebayo
by: Ganiyat Olusola , Adebayo
Published: (2019)

Thermoset plastics product recycling
by: Mokhtar, Munirah, et al.
Published: (1995)

Industrial guideline for injection moulding: case of jaundice meter
by: Naqibah, Azman, et al.
Published: (2020)

Development of mini micro injection moulding machine
by: Daelami, Aminuddin
Published: (2012)

Investigation of biomechanical and biosafety of injection moulded implant materials
by: Omar, Mohd Afian, et al.
Published: (2014)

Industrial guideline for injection moulding : case of jaundice meter
by: Azman, Naqibah, et al.
Published: (2020)

A study on the effect of injection moulding process parameters to the properties of injected parts
by: Sharifah Rafidah, Syed Hamid
Published: (2010)

Thermal properties of injection moulded polylactic acid 13 kenaf fibre biocomposite
by: Anuar, Hazleen, et al.
Published: (2011)

Injection moulded lightweight kenaf fibre thermoplastic elastomer composite for automotive components
by: Anuar, Hazleen, et al.
Published: (2011)

Comparison of Business Model Canvas (BMC) among the three consulting companies
by: Azhar Amanullah, Ayn Nur Azhana, et al.
Published: (2015)

Thermoplastics composites vs. thermoset composites
by: Mokhtar, Munirah
Published: (1995)