Influence of oil-based and water-based lubrication on tool wear of DLC/TiAlN-coated punches in blanking of stainless steel

QR Code

Influence of oil-based and water-based lubrication on tool wear of DLC/TiAlN-coated punches in blanking of stainless steel

This study aims to eliminate the use of oil-based lubricants in the metal forming process by integrating a new tribological system of double-layered Carbon/Titanium Aluminum Nitride (DLC/TiAlN) with water-based lubrication. The research compared the performance of traditional oil-based lubricant (cu...

Full description

Bibliographic Details
Main Authors:	Ibrahim, Muhammad Shuhaimi, Sulaiman, Mohd Hafis, Ismail, Mohd Idris Shah
Format:	Article
Language:	English
Published:	Malaysian Tribology Society 2025
Online Access:	http://psasir.upm.edu.my/id/eprint/120222/ http://psasir.upm.edu.my/id/eprint/120222/1/120222.pdf

Similar Items

Enhancing wear resistance in blanking and punching of stainless-steel sheets under dry friction and solid lubrication conditions using single-layer ceramic- and carbon-based hard coatings
by: Ibrahim, Muhammad Shuhaimi, et al.
Published: (2024)

Tool wear of DLC coating as top-layered to CrN, TiAlSiN, TiAlN coatings in machining of steel and aluminum alloys
by: Ibrahim, M. S., et al.
Published: (2024)

Application of ANFIS in predicting TiAlN coatings flank wear
by: Hasan Basari, Abd Samad, et al.
Published: (2011)

Performance of TialN coated carbide tool in peck drilling stainless steel SS316L with pressurized minimum quantity lubrication
by: M., Malik, et al.
Published: (2014)

Tool wear analysis in end milling of advanced ceramics with TiAlN and TiN coated carbide inserts
by: Reddy, M. Mohan, et al.
Published: (2012)

Tool wear analysis in end milling of advanced ceramics with TiAlN and TiN coated carbide inserts
by: Moola, Mohan, et al.
Published: (2012)

Application of fuzzy rule-based model in predicting flank wear of TiAlN coatings in PVD magnetron sputtering process
by: Mohamad Jaya, Abdul Syukor, et al.
Published: (2011)

Application of ANFIS in Predicting of TiAlN Coatings Hardness
by: Mohamad Jaya, Abdul Syukor, et al.
Published: (2011)

Application of ANFIS in Predicting of TiAlN Coatings Hardness
by: Mohamad Jaya, Abdul Syukor, et al.
Published: (2011)

Topography orientation effects on friction and wear in sliding DLC and steel contacts, part 3: Experiments under dry and lubricated conditions
by: Holmberg, Kenneth, et al.
Published: (2021)

Comparative study between wear of uncoated and TiAlN-coated carbide tools in milling of Ti6Al4V
by: Uddin, M., et al.
Published: (2017)

Hybrid RSM-fuzzy modeling for hardness prediction of TiAlN coatings
by: Jaya, A. S. M, et al.
Published: (2011)

Topographical orientation effects on friction and wear in sliding DLC and steel contacts, part 1: Experimental
by: Holmberg, K., et al.
Published: (2015)

Parametric optimization and modeling for flank wear of TiSiN-TiAlN Nanolaminate Cutting Insert / M. Kaladhar
by: M., Kaladhar
Published: (2020)

Investigations on joining of stainless steel tailored blanks by μ-PTA process
by: Dwibedi, Swagat, et al.
Published: (2018)

Machinability of Aluminum Nitride Ceramic using TiAlN and TiN Coated Carbide Tool Insert
by: Moola, M., et al.
Published: (2014)

Cutting performance of advanced multilayer coated (TiAlN/AlCrN) in machining of AISI D2 hardened steel
by: Jasni, Nur Akmal Hakim
Published: (2013)

Effects of coating and lubrication on friction and wear for metal-to metal application
by: Ideris, Muhammad Haziq, et al.
Published: (2023)

Wear mechanism of TC4 titanium alloy with TiN coating against self-lubricating fabric
by: Zhao, Song, et al.
Published: (2023)

Tool life of TiAlN PVD coated carbide tool in high-speed end milling of untreated inconel 718 under minimum quantity lubrication condition
by: Kasim, M.S., et al.
Published: (2013)

Milling of carbon fibre reinforced polymer (CFRP) using TiAlN coated end mills
by: Konneh, Mohamed, et al.
Published: (2014)

Development of tool life prediction model of TiAlN coated tools during the high speed hard milling of AISI H13 steel
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Laser cutting of square blanks in stainless steel-304 sheets: HAZ and thermal stress analysis
by: A.M. Sifullah,, et al.
Published: (2017)

Experimental Study on Minimum Quantity Lubrication in End Milling of AA6061-T6 Using Tialn Coated Carbide Tools
by: Najiha, M. S., et al.
Published: (2015)

Effect of laser textured DLC coated AISI 52100 steel on the tribological behavior for engine applications / Arslan Ahmed
by: Arslan, Ahmed
Published: (2017)

Microstructural aspects of wear behaviour of TiC coated low alloy steel
by: Md Idriss, A. N., et al.
Published: (2016)

Electrical discharge coating of nanostructured TiC-Fe cermets on 304 stainless steel
by: Algodi, Samer J., et al.
Published: (2016)

Structural and wear and characteristic of low temperature nitrided stainless steel
by: Haruman, E., et al.
Published: (2006)

The use of TiAIN coated carbide tool when finish machining hardened stainless steel
by: Noordin, M. Y., et al.
Published: (2007)

Wear and corrosion behavior of tungsten carbide based coating on carbon steel
by: Ahmad, Noor Aqilah, et al.
Published: (2018)

Tribological investigation of tetrahedral diamond-like carbon (ta-C DLC) coatings using vegetable oil containing anti-wear additives / Abdul Mannan
by: Abdul, Mannan
Published: (2018)

Punching tool wear modeling using finite element method
by: Melcot, Jinikol
Published: (2009)

Wear behaviour of TiC coated AISI 4340 steel produced by TIG surface melting
by: Maleque, Md. Abdul, et al.
Published: (2015)

Wear behaviour of TiC coated AISI 4340 steel produced by TIG surface melting
by: Maleque, M.A., et al.
Published: (2015)

Mechanical properties of titanium-hydroxyapatite (Ti-HA) composite coating on stainless steel prepared by thermal spraying
by: Ramli, Rosmamuhamadani, et al.
Published: (2017)

Investigate the effect of shear angle of high speed steel punching tool in punching process
by: Mohd Khairul Mizan, Nasir
Published: (2009)

Experimental Investigation of Flank Wear in end Milling of Aluminum Alloy with Water-Based TiO2 Nanofluid Lubricant in Minimum Quantity Lubrication Technique
by: Najiha, M. S., et al.
Published: (2016)

Topographical orientation effects on surface stresses influencing on wear in sliding DLC contacts, Part 2: Modelling and simulations
by: Laukkanen, A., et al.
Published: (2017)

Studying the fusion cutting mechanism in CO2 laser blanking of stainless steel-304 square samples / Abu Mohammed Sifullah
by: Abu Mohammed, Sifullah
Published: (2017)

Characterization Of β-TCP Coated On Stainless Steel 316
by: Ariff, Ummi Fatisya Ain
Published: (2022)