Determination of composite friction factor and manning roughness coefficient for Discharge estimation in natural compound channels

QR Code

Determination of composite friction factor and manning roughness coefficient for Discharge estimation in natural compound channels

A field study has been carried out at University Malaysia Sarawak (UNIMAS), aimed at a fuller understanding of the mechanics flow and also at evolving more accurate methods for overbank flow discharge estimation. The study involved four frequently flooded rivers with extensive data collected.

Bibliographic Details
Main Author:	Lai, Sai Hin
Format:	Thesis
Language:	English
Published:	Universiti Malaysia Sarawak, UNIMAS 2005
Subjects:	TA Engineering (General). Civil engineering (General)
Online Access:	http://ir.unimas.my/id/eprint/3142/ http://ir.unimas.my/id/eprint/3142/2/Lai%20Sai%20Hin..pdf

Similar Items

Determination Of Mannings Coefficient For Modular Channel
by: Dinail, Nurul Juliyana
Published: (2017)

Gradient-based estimation of Manning's friction coefficient from noisy data
by: Calo, Victor, et al.
Published: (2013)

Peak friction angle estimation from joint roughness coefficient of discontinuities of limestone in Peninsular Malaysia
by: Ailie Sofyiana Serasa,, et al.
Published: (2017)

Determining Coefficient of Discharge to Compare Coefficients of Resistance for Different Coarse Aggregate Beds
by: Shambo, M. T, et al.
Published: (2015)

Experimental determination of convective heat transfer coefficient in wire electro discharge machining
by: Nadiah Waznah, Zabidi
Published: (2008)

Study of flow in a non-symmetrical compound channel with rough flood plain
by: Bong, C.H.J
Published: (2003)

Determination of flow resistance coefficient for vegetation in open channel: laboratory study
by: Ahmad, Noor Aliza, et al.
Published: (2018)

Friction Coefficient and Wear Rate of Copper Mating with Smooth and Rough Stainless Steel 304 Counterfaces
by: Chowdhury, Mohammad Asaduzzaman, et al.
Published: (2013)

Determination of flow characteristics in the vegetated compound channels
by: Ismail, Zulhilmi, et al.
Published: (2009)

Experimental Study of Friction Coefficient and Wear Rate of Turned and Ground Mild Steel Surfaces Sliding Against Smooth and Rough SS304 Counterfaces
by: Nuruzzaman, D. M., et al.
Published: (2014)

Shear Model Development of Limestone Joints with Incorporating Variations of Basic Friction Coefficient and Roughness Components During Shearing
by: Mehrishal, S., et al.
Published: (2016)

Chip formation and coefficient of friction in turning S45C medium carbon steel
by: A. Raof, Natasha, et al.
Published: (2014)

Effect of surface roughness using different electrodes on electrical discharge machining
by: Mohd Abd Latif, Abd Ghani
Published: (2008)

Coefficient of Friction and Wear Rate Effects of Different Composite Nanolubricant Concentrations on Aluminium 2024 Plate
by: Nurul Nadia, Mohd Zawawi, et al.
Published: (2017)

Motion investigation of a snake robot with different scale geometry and coefficient of friction
by: Md Lutful Huq, Naim, et al.
Published: (2018)

Numerical analysis of disc brake squeal considering temperature dependent friction coefficient
by: Abu Bakar, A. R., et al.
Published: (2006)

Roughness Coefficient of Micro-irrigation Laterals
by: Mohd Soom, Mohd Amin
Published: (1994)

Leakage current and surface discharge phenomena : effect on tracking and morphological properties of LLDPE-natural rubber compounds
by: Piah, M. A. M., et al.
Published: (2003)

Study of machining parameters of surface roughness in electro discharge machining of tool steel
by: Zairul Ezree , Mohd Yunus
Published: (2008)

Experimental Investigation on Friction Coefficient of Composite Materials Sliding Against SS 201 and SS 301 Counterfaces
by: Nuruzzaman, D. M., et al.
Published: (2015)

Experimental Investigation of Friction Coefficient and Wear Rate of Stainless Steel 304 Sliding against Smooth and Rough Mild Steel Counterfaces
by: Chowdhury, M. A., et al.
Published: (2013)

Influence of different roughness of bed and side walls in an open channel
by: Siti Natasha, Shamshul Bahri
Published: (2014)

Frictional Behavior of Polymers Sliding Against Smooth and Rough Mild Steel Counter Faces
by: Nuruzzaman, D. M., et al.
Published: (2014)

Estimating Bankfull Discharge and Depth in Ungauged Estuaries
by: Gisen, J. I. A., et al.
Published: (2015)

Powder mixed micro electro discharge milling of titanium alloy: analysis of surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Variation of coefficient of friction and friction head losses along a pipe with multiple outlets
by: Alawee, Wissam H., et al.
Published: (2020)

Effect of substrate bias on friction coefficient, adhesion strength and hardness of tin-coated tool steel
by: Hamzah, Esah, et al.
Published: (2006)

Experimental investigation on the effect of masked multiple passes abrasive waterjet machining surface texturing on coefficient of friction
by: Hafiz, Husin, et al.
Published: (2025)

The effect of swirl number on discharge coefficient for various orifice sizes in a burner system
by: Ashrul Ishak, Mohamad Shaiful, et al.
Published: (2004)

Estimating discharge in ungauged catchment of Sungai Muar
by: Muslim, Muhammad
Published: (2016)

The effect of external grit particle size on friction coefficients and grit embedment of brake friction material
by: Hamid, M., et al.
Published: (2013)

Diffusion Coefficient Estimations by Thin-Channel Column Inverse Gas Chromatography : Preliminary Experiments
by: Mohd. Nawawi, Mohd. Ghazali
Published: (2000)

Influence of Wire Electrical Discharge Machining (WEDM) process parameters on surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Electro-discharge machining of alumina: investigation of material removal rate and surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Influence of Normal Loads and Sliding Velocities on Friction Properties of Engineering Plastics Sliding against Rough Counterfaces
by: Nuruzzaman, D. M., et al.
Published: (2016)

Surface roughness characterization on p20 tool steel in wirecut electrical discharge machining (wedm) process
by: Zaidatul Syima, Zainal
Published: (2013)

Powder Mixed Micro Electro Discharge Milling of Titanium Alloy: Analysis of Surface Roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Comparison of dry and cryogenic machining on chip formation and coefficient of friction in turning AISI 4340 alloy steel
by: A. Raof, Natasha, et al.
Published: (2014)

Nurturing nature for man
Published: (2011)

Determination of coefficient of rate of horizontal consolidation of peat soil
by: Gofar, Nurly, et al.
Published: (2006)