Electrode Wear Rate of Graphite Electrodes during Electrical Discharge Machining Processes on Titanium Alloy Ti-5Al-2.5Sn

QR Code

Electrode Wear Rate of Graphite Electrodes during Electrical Discharge Machining Processes on Titanium Alloy Ti-5Al-2.5Sn

The proper selection of machining parameters can result in better machining performance in the electrical discharge machining process. However, this job is not always easy since the phenomena occurring between the electrodes in EDM are not yet fully understood. This study reports the development of...

Full description

Bibliographic Details
Main Authors:	Khan, Md. Ashikur Rahman, M. M., Rahman, K., Kadirgama
Format:	Article
Language:	English
Published:	Universiti Malaysia Pahang 2014
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://umpir.ump.edu.my/id/eprint/8174/ http://umpir.ump.edu.my/id/eprint/8174/1/26_Khan_et_al.pdf

Similar Items

Surface Characteristics of Ti-5Al-2.5Sn in Electrical Discharge Machining Using Negative Polarity of Electrode
by: Khan, Md. Ashikur Rahman, et al.
Published: (2017)

RSM model to evaluate material removal rate in EDM of Ti-5Al-2.5Sn using graphite electrode
by: Md. Ashikur, Rahman Khan, et al.
Published: (2012)

Optimal Set-up and Surface Finish Characteristics in Electrical Discharge Machining on Ti-5al-2.5sn using Graphite
by: Khan, Md. Ashikur Rahman, et al.
Published: (2016)

An Experimental Investigation on Surface Finish in Die-Sinking EDM Of Ti-5Al-2.5Sn
by: Khan, Md. Ashikur Rahman, et al.
Published: (2015)

Performance evaluation of electrical discharge machine on titanium alloy using copper impregnated graphite electrode
by: Mohd. Isa @ Hamid, Mohd. Halimudin
Published: (2010)

Electrical Discharge Machining of Beryllium Copper Alloys Using Graphite Electrode
by: Mohamed Yusof, Shaik Mohamed
Published: (2009)

Influence of electrode profiles on electrical discharge machining of titanium
by: Zain, Zakaria Mohd, et al.
Published: (2011)

Surface integrity evaluation on titanium alloy after EDM machining using different graphite electrodes
by: Mat Jusoh, Mazlan
Published: (2010)

The influence of graphitization catalyst electrode in electrical discharge machining of polycrystalline diamond-finishing condition
by: Andias, Rino, et al.
Published: (2020)

Performance evaluation of different types of graphite electrodes on titanium (Ti - 6A1 - 4V)
by: Abdul Haq, Reazul Haq
Published: (2009)

Reducing electrode wear using cryogenic cooling during electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2010)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of electrode cooling on material migration among the electrodes during edm of titanium alloy
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Influence of electrode cooling on material migration among the electrodes during EDM of titanium alloy
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Electrical discharge machining of titanium alloy using copper tungsten electrode with SiC powder suspension dielectric fluid
by: Rival, Rival
Published: (2005)

Effect of discharge current and electrode size on material removal rate and wear ratio in electrical discharge machining
by: Khan, Ahsan Ali, et al.
Published: (2010)

Reducing electrode wear ratio using cryogenic cooling during electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2009)

Wear ratio and work surface finish during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface alloying of Ti-6Al-4V using Cu-TaC composite electrode during electrical discharge machining
by: Mohammed Baba, Ndaliman, et al.
Published: (2011)

Artificial Intelligent Approach for Machining Titanium Alloy in a Nonconventional Process
by: Khan, Md. Ashikur Rahman, et al.
Published: (2013)

Surface Study in a Non-conventional (Electrical Discharge Machining) Process for Grade 6 Titanium Material
by: Md. Ashikur, Rahman Khan, et al.
Published: (2014)

Study of material removal rate and electrode wear ratio for micro electrical discharge milling of AISI 420 and Stavax ESR
by: Mohammad, Yeakub Ali, et al.
Published: (2009)

Optimization of Machining Parameters on Tool Wear Rate of Ti-6Al-4V through EDM using Copper Tungsten Electrode A Statistical Approach
by: M. M., Rahman, et al.
Published: (2011)

Performance evaluation of wire electrical discharge machining on Titanium Alloy
by: Tan, Jun Qi, et al.
Published: (2018)

An analysis of wire-cut parameters in electric-discharge of titanium alloys
by: Nehadabed, Farook, et al.
Published: (2019)

Surface finish characteristics of titanium alloy in a non conventional technique
by: Md. Ashikur, Rahman Khan, et al.
Published: (2017)

Prediction of Surface Roughness of Ti-6Al-4V In Electrical Discharge Machining: A Regression Model
by: M., Ishak, et al.
Published: (2011)

Wear performance of TiC/Fe cermet electrical discharge coatings
by: Algodi, Samer J., et al.
Published: (2018)

Wear mechanism of TC4 titanium alloy with TiN coating against self-lubricating fabric
by: Zhao, Song, et al.
Published: (2023)

Prediction of surface roughness of ti-6al-4v in electrical discharge machining: a regression model
by: Khan, Md. Ashikur Rahman, et al.
Published: (2011)

Prediction of surface roughness of Ti-6Al-4V in electrical discharge machining: A regression model
by: Rahman Khan, Md. Ashikur, et al.
Published: (2011)

Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
by: Mohd Harun, Dalila
Published: (2020)

Electrical discharge machining of polycrystalline diamond using copper electrode – finishing condition
by: Ahmad, M.A. Haikal, et al.
Published: (2017)

Surface modification of titanium alloy through electrical discharge machining (EDM)
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Titanium alloy particles formation in electrical discharge machining and fractal analysis
by: Khilji, Irshad Ahamad, et al.
Published: (2022)

Parametric Optimization in EDM of Ti-6Al-4V using Copper Tungsten Electrode and Positive Polarity: a statistical approach
by: Rahman, Md. Mustafizur, et al.
Published: (2011)

Temperature distribution in copper electrode during electrical discharge machining process
by: Abdulkareem, Suleiman, et al.
Published: (2017)

Effect of surface roughness using different electrodes on electrical discharge machining
by: Mohd Abd Latif, Abd Ghani
Published: (2008)

The Reduction of Nickel Slags by Graphite Electrodes using AC and DC Current
by: Dal, Ismail, et al.
Published: (1997)

Features of electrode wear during EDM of mild steel with TaC-Cu powder compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)