Prevention of Wrinkling in Shrink Flanging of Ultra-High Strength Steel Sheets Using Gradually Contacting Punch

QR Code

Prevention of Wrinkling in Shrink Flanging of Ultra-High Strength Steel Sheets Using Gradually Contacting Punch

To prevent the occurrence of wrinkling in the shrink flanging of ultra-high strength steel sheets, a gradually contacting punch was developed. Compressive stress around the convex corner of the sheet in shrink flanging was reduced by gradually bending the edge from the center to the outside of the s...

Full description

Bibliographic Details
Main Authors:	Zamzuri, Hamedon, Mori, Ken-ichiro, Abe, Yohei, Watanabe, Saharu
Format:	Article
Language:	English
Published:	2014
Subjects:	TS Manufactures
Online Access:	http://umpir.ump.edu.my/id/eprint/7724/ http://umpir.ump.edu.my/id/eprint/7724/1/fkp-2014-zamzuri-Prevention_of_wrinkling.pdf

Similar Items

Hemming for Joining High Strength Steel Sheets
by: Zamzuri, Hamedon, et al.
Published: (2014)

Thickened holes edge including compressed rollover for improving tensile fatigue strength of thick sheet
by: Zamzuri, Hamedon, et al.
Published: (2018)

Design of Hollow Section of High Strength Steel Sheets Join by Hemming Process for Energy Absorbtion Application
by: Zamzuri, Hamedon, et al.
Published: (2016)

In-situ Measurement of Three-dimensional Deformation Behaviour of Sheet and Tools During Stamping Using Borescope
by: Zamzuri, Hamedon, et al.
Published: (2014)

Enhancing flange length in stamping of high strength steel sheets sm520b using stretch flanging method
by: Mohd Syafiq, Yusoff
Published: (2020)

Prevention of Crack In Stretch Flanging Process Using Hot Stamping Technique
by: Y., Mohd Syafiq, et al.
Published: (2017)

Effect of small corner radius in cold punching of 22MnB5 die-quenched boron steel sheets
by: Hasnulhadi, Jaafar, et al.
Published: (2022)

Experimental study on process parameter to reduce wrinkling in sheet metal forming
by: Nik Muhd Hazwan, Nik Abd Aziz
Published: (2013)

Docs welcome gradual reopening
by: Tang, Ashley
Published: (2020)

Design and simulation of die and punch for sheet metal on round bending
by: Teh, Soon Chiang
Published: (2007)

Investigation on a new hole-flanging approach by incremental sheet forming through a featured tool
by: Cao, Tingting, et al.
Published: (2016)

Classification of transient facial wrinkle
by: Rosdiyana, Samad, et al.
Published: (2019)

A study on the evolution of the contact angle of small punch creep test of Ductile materials
by: Cacciapuoti, B., et al.
Published: (2016)

Set Up Reduction On Sheet Metal Fabrication Company C's CNC Punching Section
by: Loh, Hong Yi
Published: (2017)

In-situ measurement and formability improvement in stamping of high strength steel and titanium alloy sheets
by: Zamzuri, Hamedon
Published: (2014)

A review on the bolted flange looseness detection method
by: Mohd Padzly, Radzi, et al.
Published: (2023)

Prediction of wrinkling using finite element simulation
by: Mohd Fizree, Abdul Razak
Published: (2013)

Reducing wrinkling and tearing of deep draw part
by: Mohd Naeemil Mahmudi, Mahmud
Published: (2012)

Femur open wedge corrective osteotomy and gradual deformity correction
by: Ang, Poh Thean Charles,, et al.
Published: (2019)

Optimal gradual liquidation of equity from a risky asset
by: Dokuchaev, Nikolai
Published: (2010)

Mafi gradually shifting to output orientation in providing subsidies to farmers
by: Borneo Post Sarawak
Published: (2021)

A cross-sectional study to assess pattern in wrinkle formation in different age groups in female population in Kelantan
by: Jimeno IV, Zosimo Ken L.
Published: (2018)

Rotating flow over an exponentially shrinking sheet with suction
by: Rosali, Haliza, et al.
Published: (2015)

CFD investigation of empty flanged diffuser augmented wind turbine
by: Jabbar Al-Quraishi, Balasem Abdulameer, et al.
Published: (2019)

BUCKLING BEHAVIOUR OF ANGLE SECTION BEAM WITH THE UNSTIFFENED FLANGES IN COMPRESSION
by: Sivakumar, Dhar Malingam, et al.
Published: (2006)

Prevention of Springback of High Strength Steel Sheet in L-Bending Process
by: Mohd Syafiq, Yusoff, et al.
Published: (2016)

Unsteady shrinking sheet with mass transfer in a rotating fluid
by: Md. Ali, Fadzilah, et al.
Published: (2011)

Numerical solutions of Wang's stretching/shrinking sheet problem for nanofluids
by: Md Ali, Fadzilah, et al.
Published: (2013)

Stability analysis of Wang's stretching/shrinking sheet problem for nanofluids
by: Junoh, Mohamad Mustaqim, et al.
Published: (2019)

Investigate the effect of shear angle of high speed steel punching tool in punching process
by: Mohd Khairul Mizan, Nasir
Published: (2009)

An Experimental and Numerical Investigation of the Vibrational Response of a Flanged Cylinder Structure
by: Wilkes, D., et al.
Published: (2017)

Comparison of filtering methods for extracting transient facial wrinkle features
by: Rosdiyana, Samad, et al.
Published: (2018)

Kinematic differences between gradual and impulsive coronal mass ejections: the role of flares
by: Hamidi, Z.S., et al.
Published: (2024)

Designing and fabricating the punch chuck and precision hole punch diameter 3.0mm, 3.5mm and 4.0mm for turret punch machine
by: Prabagar, Murukesavan
Published: (2008)

MHD stagnation point flow with suction towards a shrinking sheet
by: Lok, Yian Yian, et al.
Published: (2011)

Stagnation-point flow past a shrinking sheet in a nanofluid.
by: Nazar, Roslinda, et al.
Published: (2011)

Flow and heat transfer of a nanofluid over a shrinking sheet
by: Bachok @ Lati, Norfifah, et al.
Published: (2014)

Application of CAD/CAM in the design of machining process and tooling devices for flange tube
by: Musa Alhaji Ibrahim,, et al.
Published: (2020)

Fiber Bragg Grating Gap Sensor as An Innovative Idea for Critical Flange Monitoring
by: Mohd Hafizi, Zohari
Published: (2022)

Facile synthesis of fibrous zeolite Y with a radial wrinkle structure
by: Nornasuha, Abdullah, et al.
Published: (2022)