A study on tool deflection during deep pocketing cycle
Tool deflection during deep pocketing cycle will cause tapper in mould and die. This problem can cause defect on final product and also increases cost and time wasting in manufacturing process. This study basically shows a detailed study to overcome tapper problem in deep pocket. Dimensional accurac...
| Main Author: | |
|---|---|
| Format: | Undergraduates Project Papers |
| Language: | English |
| Published: |
2013
|
| Subjects: | |
| Online Access: | http://umpir.ump.edu.my/id/eprint/6560/ http://umpir.ump.edu.my/id/eprint/6560/1/05.A%20study%20on%20tool%20deflection%20during%20deep%20pocketing%20cycle.pdf |
| _version_ | 1848817802866065408 |
|---|---|
| author | Zikrulhakim, Muhd Zahid |
| author_facet | Zikrulhakim, Muhd Zahid |
| author_sort | Zikrulhakim, Muhd Zahid |
| building | UMP Institutional Repository |
| collection | Online Access |
| description | Tool deflection during deep pocketing cycle will cause tapper in mould and die. This problem can cause defect on final product and also increases cost and time wasting in manufacturing process. This study basically shows a detailed study to overcome tapper problem in deep pocket. Dimensional accuracy due to tapper problem was analyzed in order to obtain optimum cutting parameters. The pocket part was drawn by using CATIA software. The data collected during experiment was analyzed using signal to noise ratio through Minitab software. From the analysis, it was found that depth of cut has gives the most effect on tapper problem, followed by feed rate and spindle speed. From the result, it is shown that level 1 of depth of cut which is 0.3mm, level 1 of feed rate which is 64mm and level 2 of spindle speed which is 1280rpm was the best cutting parameter. Hence, from these cutting parameters, the tapper problem cause by tool deflection during deep pocketing cycle can be overcome. |
| first_indexed | 2025-11-15T01:27:34Z |
| format | Undergraduates Project Papers |
| id | ump-6560 |
| institution | Universiti Malaysia Pahang |
| institution_category | Local University |
| language | English |
| last_indexed | 2025-11-15T01:27:34Z |
| publishDate | 2013 |
| recordtype | eprints |
| repository_type | Digital Repository |
| spelling | ump-65602023-03-20T03:03:40Z http://umpir.ump.edu.my/id/eprint/6560/ A study on tool deflection during deep pocketing cycle Zikrulhakim, Muhd Zahid TA Engineering (General). Civil engineering (General) Tool deflection during deep pocketing cycle will cause tapper in mould and die. This problem can cause defect on final product and also increases cost and time wasting in manufacturing process. This study basically shows a detailed study to overcome tapper problem in deep pocket. Dimensional accuracy due to tapper problem was analyzed in order to obtain optimum cutting parameters. The pocket part was drawn by using CATIA software. The data collected during experiment was analyzed using signal to noise ratio through Minitab software. From the analysis, it was found that depth of cut has gives the most effect on tapper problem, followed by feed rate and spindle speed. From the result, it is shown that level 1 of depth of cut which is 0.3mm, level 1 of feed rate which is 64mm and level 2 of spindle speed which is 1280rpm was the best cutting parameter. Hence, from these cutting parameters, the tapper problem cause by tool deflection during deep pocketing cycle can be overcome. 2013-06 Undergraduates Project Papers NonPeerReviewed pdf en http://umpir.ump.edu.my/id/eprint/6560/1/05.A%20study%20on%20tool%20deflection%20during%20deep%20pocketing%20cycle.pdf Zikrulhakim, Muhd Zahid (2013) A study on tool deflection during deep pocketing cycle. Faculty of Manufacturing Engineering, Universiti Malaysia Pahang. |
| spellingShingle | TA Engineering (General). Civil engineering (General) Zikrulhakim, Muhd Zahid A study on tool deflection during deep pocketing cycle |
| title | A study on tool deflection during deep pocketing cycle |
| title_full | A study on tool deflection during deep pocketing cycle |
| title_fullStr | A study on tool deflection during deep pocketing cycle |
| title_full_unstemmed | A study on tool deflection during deep pocketing cycle |
| title_short | A study on tool deflection during deep pocketing cycle |
| title_sort | study on tool deflection during deep pocketing cycle |
| topic | TA Engineering (General). Civil engineering (General) |
| url | http://umpir.ump.edu.my/id/eprint/6560/ http://umpir.ump.edu.my/id/eprint/6560/1/05.A%20study%20on%20tool%20deflection%20during%20deep%20pocketing%20cycle.pdf |