Effect of abrasive water jet machining parameters on aramid fibre reinforced plastics composite

QR Code

Effect of abrasive water jet machining parameters on aramid fibre reinforced plastics composite

This paper presents a study on the effect of abrasive water jet machining (AWJM) process parameters on surface roughness (R a) and kerf taper ratio (T R) of aramid fibre reinforced plastics (AFRP) composite. Taguchi’s design of experiment was used as the experimental approach. Through analysis of va...

Full description

Bibliographic Details
Main Authors:	Azhari, Azmir, Amimul K., Ahsan, A., Rahmah
Format:	Article
Language:	English
Published:	springer
Subjects:	TA Engineering (General). Civil engineering (General) TJ Mechanical engineering and machinery TS Manufactures
Online Access:	http://umpir.ump.edu.my/id/eprint/45046/ http://umpir.ump.edu.my/id/eprint/45046/1/Effect%20of%20abrasive%20water%20jet%20machining%20parameters.pdf

Similar Items

Effect of abrasive water jet machining parameters on aramid fibre reinforced plastics composite
by: Azhari , Mohd Azmir, et al.
Published: (2009)

Effect of Process Parameters on Abrasive Contamination During Water Abrasive Jet Machining of Mild Steel
by: Afifah, Ali, et al.
Published: (2010)

Investigation on glass/epoxy composite surfaces machined by abrasive water jet machining
by: Mohd Azhari, Mohd Azmir, et al.
Published: (2008)

Application of silicon carbide in abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2011)

Effect of process parameters on abrasive contamination during water abrasive jet machining of mild steel
by: Mohd Ali, Afifah, et al.
Published: (2011)

A Review on Nozzle Wear in Abrasive Water Jet Machining Application
by: Syazwani, H., et al.
Published: (2016)

A study on abrasive water jet machining of aluminum with garnet abrasives
by: Khan, Ahsan Ali, et al.
Published: (2005)

Performance of different abrasive materials during abrasive water jet machining of glass
by: Khan, Ahsan Ali, et al.
Published: (2007)

Surface roughness of carbides produced by water abrasive jet machining
by: Ali Khan, Ahsan, et al.
Published: (2011)

Surface roughness of Carbides produced by abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2005)

Investigation of the wear progression of nozzle in abrasive waterjet machining with different abrasive material
by: Lusi, Nuraini, et al.
Published: (2025)

Analysis of wear on abrasive water jet nozzle
by: Izzudin, Nazar
Published: (2016)

A study of abrasive water jet machining process on glass/epoxy composite laminate
by: M. A., Amir, et al.
Published: (2009)

Investigation on the effect of abrasive waterjet parameter on machining stainless steel
by: Hafiz, Husin, et al.
Published: (2020)

Analysis of acoustic emission during abrasive waterjet machining of sheet metals
by: Nazrin, Mokhtar, et al.
Published: (2018)

Kenaf-aramid fibre-reinforced polyvinyl butyral hybrid composites for military helmet
by: Salman, Suhad Dawood
Published: (2017)

Performance analysis of abrasive waterjet machining process at low pressure
by: M., Murugan, et al.
Published: (2018)

Optimization Of Abrasive Waterjet Machining Process Parameters Using Orthoganalarray With Grey Relational Analysis
by: Azmir, Azhari, et al.
Published: (2007)

Design and fabrication of a new replaceable nozzle for abrasive water jet application
by: Nuraini, Lusi, et al.
Published: (2025)

Prediction of abrasive waterjet machining of sheet metals using artiﬁcial neural network
by: Nur Khadijah, Mazlan, et al.
Published: (2022)

Prediction of abrasive waterjet machining of sheet metals using artificial neural network
by: Nur Khadijah, Mazlan, et al.
Published: (2022)

Impact of pressure on surface roughness and kerf characteristics using low pressure abrasive water jet cutting
by: Nazrin, Mokhtar, et al.
Published: (2024)

Flexural strength and failure behavior of glass laminate aluminum reinforced epoxy and aluminum-lithium laminates in abrasive water jet peening under contamination
by: Qutaba, Syed, et al.
Published: (2025)

Experimental investigation on the effect of masked multiple passes abrasive waterjet machining surface texturing on coefficient of friction
by: Hafiz, Husin, et al.
Published: (2025)

Machinability study of structural automotive alloys using abrasive waterjet machining process
by: Azhari, Azmir, et al.
Published: (2019)

Effect Of Surface Topography Of 8090 Al-Li Alloy During Abrasive Waterjet Peening Process
by: Qutaba, Syed, et al.
Published: (2024)

Assembly meshing of abrasive waterjet nozzle erosion simulation
by: Naqib Hakim, Kamarudin, et al.
Published: (2017)

A scientometrics review of nozzle wear in abrasive waterjet machining
by: Nuraini, Lusi, et al.
Published: (2025)

Evaluation Of Natural And Synthetic Fibres Reinforced Polyester Composites Subjected To Adhesive And Abrasive Wear Modes
by: Yousif, Belal F.
Published: (2008)

A four-decade of abrasive waterjet processing technology (1980-2023): a scientometric analysis
by: Lusi, Nuraini, et al.
Published: (2025)

Machinability study of ultrasonic assisted machining (UAM) of carbon fibre reinforced plastic (CFRP) with multifaceted tool
by: Abd Halim, Nor Farah Huda, et al.
Published: (2016)

Optimization of milling carbon fibre reinforced plastic under chilled air machining
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2017)

Effect of masked abrasive waterjet texturing on surface roughness using Taguchi method
by: Hafiz, Husin, et al.
Published: (2022)

Tin slag polymer concrete strengthening by basalt and aramid fiber reinforced polymer confinement
by: Muhamad Soffi, Manda, et al.
Published: (2022)

Development of a low-cost miniature waterjet machine for micromachining application
by: Azhari, Azmir
Published: (2017)

Optimization of cutting parameters of sugar palm fiber- reinforced unsaturated polyester composite with laser beam and abrasive water jet cutting technologies
by: Masoud, Fathi Aluhishi Muftah
Published: (2023)

Surface integrity of Mg-based nanocomposite produced by Abrasive Water Jet Machining (AWJM)
by: Mardi, K., et al.
Published: (2017)

A study on the economic using of steel slag aggregate in asphalt mixtures reinforced by aramid fiber
by: Alnadish, Adham, et al.
Published: (2018)

Abrasive wear performance of untreated SCF reinforced polymer composite
by: ELTAYEB, N
Published: (2008)

Physical properties of durian skin fibre reinforced plasticized polylactic acid biocomposite
by: Anuar, Hazleen
Published: (2019)