Micromilling performance analysis – cold air assisted aluminium machining behaviour observation

QR Code

Micromilling performance analysis – cold air assisted aluminium machining behaviour observation

The primary goal of this work is to investigate the performance of micro mill tools in terms of tool wear, average surface roughness, and chip size when machining aluminium alloy, as well as to evaluate the effect of cutting fluid application, using a 0.9 mm tungsten carbide (WC) tool with two flute...

Full description

Bibliographic Details
Main Authors:	Nurul Hasya, .Md Kamil, Mohd Nizar, Mhd Razali, Ahmad Shahir, Jamaludin, Siti Nadiah, Mohd Saffe
Format:	Conference or Workshop Item
Language:	English English
Published:	IEEE 2022
Subjects:	TJ Mechanical engineering and machinery TS Manufactures
Online Access:	http://umpir.ump.edu.my/id/eprint/42431/ http://umpir.ump.edu.my/id/eprint/42431/1/Micromilling%20performance%20analysis%20%E2%80%93%20cold%20air%20assisted%20aluminium%20machining%20behaviour%20observation%20%28intro%29.pdf http://umpir.ump.edu.my/id/eprint/42431/2/Micromilling%20performance%20analysis%20%E2%80%93%20cold%20air%20assisted%20aluminium%20machining%20behaviour%20observation.pdf

Similar Items

Micromilling performance analysis – cold air assisted aluminium machining behaviour observation
by: Nurul Hasya, Md. Kamil, et al.
Published: (2022)

Recent Study on Hard to Machine Material – Micromilling process
by: Ainur Munira, Rosli, et al.
Published: (2021)

Tool Wear Observation During Unconventional Low Speed Machining Using Low Cost Micromilling
by: Ainur Munira, Rosli, et al.
Published: (2021)

Study on the behavior of micromilling process with the validation of finite element method
by: Nurul Hasya, Md Kamil
Published: (2025)

Minimum chip thickness in machining MEMS structure using Tool Based Micromilling
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Environmental Generation of Cold Air for Machining
by: Ginting, Y., et al.
Published: (2016)

Surface texturing potential on carbide insert in reducing aluminium alloy adhesiveness during machining
by: Chia, Yun Qi, et al.
Published: (2019)

Investigation of vibration in micromilling with MQL: S/N ratio analysis
by: Hussin, Muhammad Shaffiq, et al.
Published: (2020)

Micromilling of tungsten carbide using focused ion beam
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Noble tool based micromilling for nanometric surface finish
by: Ali, Mohammad Yeakub
Published: (2011)

Effect of minimum quantity lubrication on surface roughness in tool-based micromilling
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Cold compression in direct recycling of aluminium 6061
by: Chan, Boon Loong
Published: (2016)

Fabricating micromilling tool using wire electrodischarge grinding and focused ion beam sputtering
by: Ali, Mohammad Yeakub, et al.
Published: (2006)

Temperature and heat flow analysis in a drying chamber through finite element method
by: Nurul Hasya, .Md Kamil, et al.
Published: (2022)

Direct recycling of aluminium 6061 chip through cold compression
by: Chan, B.L., et al.
Published: (2015)

Grinding using cold air cooling
by: Boswell, Brian, et al.
Published: (2016)

Bold approach in finite element simulation on minimum quantity lubrication effect during machining
by: Ainur Munira, Rosli, et al.
Published: (2019)

Experimental investigation of vibration chatter in micromilling with minimum quantity lubrication: Analysis of signal-to-noise ratio and variance
by: Mohammad Yeakub, Ali, et al.
Published: (2024)

Improving Efficiency of Aluminium Sacrificial Anode Using Cold Work Process
by: Asmara, Y. P., et al.
Published: (2016)

Improving Efficiency of Aluminium Sacrificial Anode Using Cold Work Process
by: Asmara, Y. P., et al.
Published: (2016)

Solution heat treatment of gas-atomised aluminium alloy powder for cold spray
by: Sabard, Alexandre
Published: (2020)

Design and development of the aluminium-air battery
by: Yong, Cheng Jie
Published: (2021)

Electro-modeling of the aluminium-air battery
by: Koh, Yann Yee
Published: (2021)

The study on milling machining for aluminium alloy
by: Goh, H.W
Published: (2004)

A review on an innovative approach for efficient nanoparticles synthesis by electrical discharge machining
by: Khilji, Irshad Ahamad, et al.

Experimental observation of controllable kinetic constraints in a cold atomic gas
by: Valado, M.M., et al.
Published: (2016)

Investigation on the material compositions on air cathode in an aluminium- air battery
by: Koh, Zu Heng
Published: (2024)

Observation of built-up edge formation on a carbide cutting tool with machining aluminium alloy under dry and wet conditions
by: Azlan, U. A. A., et al.
Published: (2017)

Prediction of geometric defects in the cold embossing of AA6061 aluminium alloy by finite element analysis
by: Abdullah, Ahmad Baharuddin, et al.
Published: (2012)

Heat-assisted machining
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Ultrasonic assisted machining
by: Ascroft, Helen, et al.
Published: (2016)

Investigation of cellulose separator in aluminium-air battery
by: Lye, Jun Yan
Published: (2024)

Development of thin film for aluminium- air battery
by: Wong, Ryan Kok Seng
Published: (2024)

Electrical discharge machining of 6061 aluminium alloy
by: Pramanik, Alokesh, et al.
Published: (2015)

Effect of aging on machinability of 6061 aluminium alloy
by: Emir Izwandy, Dzulkafli
Published: (2010)

Machine vision for the measurement of machining parameters: A review
by: Abdul Wahab, Hashmi, et al.
Published: (2022)

Process damping technique for aluminium alloy at low speed machining
by: Mohd Azfadir, Mat Daud
Published: (2012)

Opportunities and ehallenges in Nanoparticles Formation by Electrical Discharge Machining
by: Khilji, Irshad Ahamad, et al.
Published: (2021)

Gas Separation Performance through Carbon Membrane: The Effect of Polymer Composition
by: Mohd Syafiq, Sharip, et al.
Published: (2020)

Observations and radiative transfer modelling of a massive dense cold core in G333
by: Lo, N., et al.
Published: (2011)