Design of synchronous serial communication to control pitches of angklung

QR Code

Design of synchronous serial communication to control pitches of angklung

This thesis describes the control device angklung (traditional musical instrument) with a 3 octave by using microcontroller. Each angklung pitch should be shaken to produce intonation. The electric motor is used as a vibrator mechanism and installed on every pitch angklung. Parameters such as the ti...

Full description

Bibliographic Details
Main Author:	Anas Muzamil, Hamiddin
Format:	Undergraduates Project Papers
Language:	English
Published:	2013
Subjects:	TA Engineering (General). Civil engineering (General) TS Manufactures
Online Access:	http://umpir.ump.edu.my/id/eprint/38500/ http://umpir.ump.edu.my/id/eprint/38500/1/ANAS%20MUZAMIL%20BIN%20HAMIDDIN.pdf

Similar Items

Design of synchronous serial communication to control pitches of angklung
by: Anas Muzamil, Hamiddin
Published: (2013)

Design and fabrication of multipurpose container
by: Anas Muzamil, Hamiddin
Published: (2009)

Serial turbo decoder for robust communication
by: Chuah, T.C., et al.
Published: (2005)

Design of MIDI decoder for auto angklung
by: Anis Hazwana, Mohamad Wazir
Published: (2013)

Computer control based "Angklung" traditional musical instrument
by: Anuar, Abd Rahman
Published: (2009)

Design of control signal for electrical drive system for technology demonstrator
by: Mohd Hasnul Mubakir, Osman
Published: (2013)

Development of asynchronous serial data comparator using fpga
by: Arwena, Abdullah
Published: (2006)

Multivariable nonlinear control of STATCOM for synchronous generator stabilization
by: Sahoo, N
Published: (2004)

Serial computer communications
by: Zen, H.
Published: (1998)

Comparison of mabsa, PSO and GWO of PI-PD controller for dc motor
by: Nur Naajihah, Ab Rahman
Published: (2024)

Product service system with inventory control for production line of a metal industry
by: Farah Ameelia, Mohammad
Published: (2024)

Designing human robot interaction for emotionally expressive robotic head AMIR-iii
by: Iqbal, A., et al.
Published: (2011)

Design and Development of Material Requirement Planning (MRP)Tool for an Electronic Product Manufacturer
by: Abdullah, Rohana, et al.
Published: (2011)

Effect of variable helix and pitch tool geometries on process damping performance in endmilling process
by: Muhammad Adib, Shaharun
Published: (2015)

Path towards an attainable quality : the effect of tooling design on the product competency and process efficiency
by: Tamilarasi, Arasu
Published: (2023)

Sinusoidal PWM controller of voltage source inverter for better efficiency of three phase induction motor
by: Chew, Hong Ping
Published: (2013)

Analysis and design of control system for desktop size concrete 3D printer
by: Iqbal, A. R., et al.
Published: (2022)

Optimization of magneto-rheological fluid in squeeze mode using combined d-optimal mixture design
by: Siti Aishah, Wahid
Published: (2019)

Design and Fabrication of a Mutual Control Electronic Circuit for Solar and Electrical Water Heating
by: Al-Talib, Ammar A., et al.
Published: (2023)

Improving particle swarm optimization via adaptive switching asynchronous – synchronous update
by: Nor Azlina, Ab. Aziz, et al.
Published: (2018)

Comparison of performance of no-clean and water-soluble fluxes in fine-pitch flip-chip package / Saif Wakeel
by: Saif , Wakeel
Published: (2021)

A fitness-based adaptive synchronous-asynchronous switching in simulated kalman filter optimizer
by: Nor Azlina, Ab. Aziz, et al.
Published: (2019)

Ethnic recognition system for malay language speakers using gammatone frequency cepstral coefficients pitch (GFCCP) and pattern classification
by: Mohd Hanifa, Rafizah
Published: (2022)

Design and fabricate chair with flip table
by: Mohd Iqbal Anas, Mat Nawi
Published: (2007)

Design and fabrication of active vibration isolation system for free space optics communication
by: Turahim, Khairiah K., et al.
Published: (2012)

The Effect Of Roof Slope On The Wind Pressure Distribution Of A Low-Rise Mono-Pitch House Using Cfd Simulation
by: Jawari, Muhammad Faiz Ahmad
Published: (2022)

Cost analysis of using hybrid microwave post-sintered silicon nitride inserts
by: Ariff, Tasnim Firdaus, et al.
Published: (2015)

Influence of backcutting phenomena to surface roughness of hardened AISI H13 during high speed end milling process
by: Mohd Ali, Afifah, et al.
Published: (2011)

Experimental investigations in high-speed hard turning of AISI 4340 steel using mixed ceramic
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Coating for high speed cutting tools
by: -, Suryanto
Published: (2011)

Development of tooling cost model in high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Development of new model for cutting force in high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Prediction of recycle method using relevance vector machine
by: Mat Noor, Muhamad, et al.
Published: (2011)

Experimental and Numerical Study on the Low Cycle Fatigue Behaviour of a Cast Hybrid Metal Matrix Composites
by: Iqbal, AKM Asif, et al.
Published: (2014)

Comparison of Polyjet Printing and Silicon Moulding as Rapid Plastic Moulding Solution
by: Singh, Rupinder
Published: (2012)

Effect of Workpiece Volume on Shell Wall Thickness Reduction in Rapid Casting of Aluminum using Three-Dimensional Printing
by: Singh, Rupinder, et al.
Published: (2012)

Cr-Ni Alloy Electrodeposition and Comparison with Conventional Pure Cr Coating Technique
by: Moniruzzaman, M., et al.
Published: (2012)

PSO-LFDE Algorithm on Constrained Real-Parameter Optimisation Test Functions
by: Nafrizuan, Mat Yahya, et al.
Published: (2023)

Perception of Employees on Lean Six Sigma Practices and Corporate Sustainability in Automotive Manufacturing Industry
by: Nur Syahirah, Mohamad Azlan, et al.
Published: (2023)

Optimization of the Automotive Manufacturing Plant Using Systematic Layout Planning (SLP) with Modular Layout
by: Muhammed Nafis, Osman Zahid, et al.
Published: (2023)