Failure analysis on the drillpipe due to the twist-off

QR Code

Failure analysis on the drillpipe due to the twist-off

This thesis reports on the design and analysis for failure at three different drill pipes. When drilling boreholes, for example in the Oil & Gas industry, a hole is drilled into the ground which can be several kilometers long. One of main type of problem that can occur while drilling is the torq...

Full description

Bibliographic Details
Main Author:	Mohd Iqbal, Mohd Zolkepeli
Format:	Undergraduates Project Papers
Language:	English English
Published:	2008
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://umpir.ump.edu.my/id/eprint/344/ http://umpir.ump.edu.my/id/eprint/344/1/ http://umpir.ump.edu.my/id/eprint/344/2/Mohd.Iqbal_Mohd._Zolkepeli.pdf

Similar Items

Tri-axial Time-frequency Analysis for Tool Failures Detection in Deep Twist Drilling Process
by: M. H. S., Harun, et al.
Published: (2016)

Analysis of Tri-axial Force and Vibration Sensors for Detection of Failure Criterion in Deep Twist Drilling Process
by: Mohd Hazwan Syafiq , Harun, et al.
Published: (2017)

Diagnosis of Twisted Blade in Rotor System
by: M. H., Lim, et al.
Published: (2015)

Finite element simulation of twist forming process to study twist springback pattern
by: Nashrudin, M. N., et al.
Published: (2017)

Failure of roof truss due to extreme wind in Malaysia : a study on consultant perspective
by: Nurul Huda, Azizan
Published: (2014)

Effect of diameter, twist angle, and blade count on the thermal-hydraulic performance of a decaying twisted swirler
by: At-Tasneem, Mohd Amin, et al.
Published: (2023)

Twisted pair cable fault diagnosis via random forest machine learning
by: Ghazali, N. B., et al.
Published: (2022)

Turbulent Forced Convection Heat Transfer of Nanofluids with Twisted Tape Insert in a Plain Tube
by: Azmi, W. H., et al.
Published: (2013)

Effect Of Similar And Dissimilar Aluminum Alloy Tailor Welded Blank To Twist Springback
by: Nasir, Iskandar Mirza Mohd
Published: (2021)

Failure analysis of input shaft
by: Mohamad Ridhwan, Ruslan
Published: (2008)

Failure analysis of input shaft
by: Mohamad Ridhwan, Ruslan
Published: (2008)

Wear Analysis On Different Customized Twist Drill Bit Designs In Drilling Cfrp Panel
by: Hashimi, Nur Hatin Raihana
Published: (2021)

Augmentation of Turbulent Flow Heat Transfer in A Horizontal Tube with Varying Width Twisted Tape Inserts
by: Sarad, S. Naga, et al.
Published: (2012)

Heat transfer augmentation of water based TIO2 AND SIO2 nanofluids in a tube with twisted tape
by: Azmi, W. H.
Published: (2015)

Ductile failure analysis of API steel pipe using strain based failure criteria
by: Siti Firdaus, Md Salleh
Published: (2013)

Failure of drive shaft using finite element analysis
by: Mohd Zulhilmi, Md Yusof
Published: (2010)

Investigation Of Non-Uniform Thickness Section Effect On Twist Springback Behaviour
by: Nashrudin, Muhammad Nazmi
Published: (2018)

Analysis of gauge glass failure possibility for boiler
by: Nur Farida, Ismail
Published: (2007)

Failure analysis of a submersible pump shaft
by: Jayabalan, J. Kulasegaran
Published: (2007)

Failure analysis of surface defects on aluminium extrudates
by: Chong, Chee Hao
Published: (2020)

Experimental Investigation of Turbulent Heat Transfer by Counter and Co-Swirling Flow in a Flat Tube Fitted with Twin Twisted Tapes
by: M. Kh., Abdolbaqi, et al.
Published: (2016)

Numerical Validation of Experimental Heat Transfer Coefficient with SiO2 Nanofluid Flowing in a Tube with Twisted Tape Inserts
by: Azmi, W. H., et al.
Published: (2014)

Effect Of Twist Drill Geometry And Drilling Parameters On Thrust Force In Single-Shot Drilling Of Stack-Up Material
by: Chim, Yi Shen
Published: (2017)

Comparison of Convective Heat Transfer Coefficient and Friction Factor of TiO2 Nanofluid flow in a tube with Twisted Tape Inserts
by: Azmi, W. H., et al.
Published: (2014)

Laminar Convective Heat Transfer And Friction Factor Of AL2O3 Nanofluid In Circular Tube Fitted With Twisted Tape Inserts
by: Sharma, Korada Viswanatha, et al.
Published: (2011)

Failure of pistons engine using finite element analysis
by: Zarul Shazwan, Zullkafli
Published: (2010)

The Use Of Response Surface Methodology (RSM) To Optimize The Twist Drill Geometry In Single Shot Drilling Of Stacked Alumina-Carbon Composite Layer
by: Mohd Adnan, Muhammad Aimi
Published: (2018)

Design of a blow off valve for turbocharged engine applications
by: Mohd Fadhli, Mohd Nasir
Published: (2007)

Reliability Analysis and Prediction of Time to Failure Distribution of an Automobile Crankshaft
by: Salvinder Singh, Karam Singh, et al.
Published: (2015)

Wind hazard risk assessment due to topographical condition
by: Mohd Fariq, Ahmad Jamil
Published: (2014)

Heat transfer enhancement of bioglycol/water based TiO2 and SiO2 nanofluids in a flat tube with twin twisted tapes
by: Abdolbaqi, Mohammed Khdher
Published: (2017)

Water hammer analysis on high pressure due to stopping pump / Nur Zalynda Zakaria
by: Nur Zalynda , Zakaria
Published: (2019)

A study on ship capsizing due to collision
by: Ibn Awal, Zobair, et al.
Published: (2008)

Vulnerability assessment due to wind storm impact
by: Mohamad Hafizi, Baharom
Published: (2014)

Vibration Analysis Of The Dam Physical Model Due To The Effect Of Water Spilling
by: Ganesan, Raguvaran
Published: (2019)

Tool Failure in Die Casting
by: Abdulhadi, Hassan A., et al.
Published: (2019)

Failure analysis of pipe joint spiral wound gasket using finite element analysis (FEA)
by: Zainulariffin, Awang
Published: (2010)

Modeling of dynamic response of desktop computer’s motherboard due to drop impact
by: Abdul Malik, Mohd. Maarif
Published: (2010)

Failure Mode and Effects Analysis of Diesel Engine for Ship Navigation System Improvement
by: Faturachman, Danny, et al.
Published: (2013)

Factor analysis on spur gear failure using computational simulation / Emilia Norazmi
by: Emilia, Norazmi
Published: (2021)